Reviews
Good.
Easier and better rearward visibility. View detail
Mirror by Yamaha
This is something that is inevitably needed because Yamaha's Mirror uses Opposite Thread Screws. View detail
Angle the Mirror
The Mirror Holder for the external Master Cylinder is only 90 degrees to the Cylinder, and the angle is different from that of the Normal Clutch Side Holder. Although this is not the normal way to use the Mirror Holder, this product can be used to match the angle and position of the Mirror Holder on the NORMAL side without any discomfort. The angle is about 20 degree backward inclination. When I used it for brembo, I had to widen the hole slightly, but when I used it for MT-10's Normal clutch, I felt almost no discomfort. View detail
Fits: YAMAHA , YAMAHA MT-25, YAMAHA FZ8, YAMAHA FZ1, YAMAHA MT-03
For MT-09 2021 and up
I was using a YAMAHA For M6, the less heavy one, and replaced it with this one.
The high-sider Mirror is EXACTLY hooked and the Handlebar vibration is pleasantly reduced.
It is not listed as compatible, but it will fit into the MT-09 from 2021 onwards with Exactly.
View detail
I'm glad it's rust resistant!
I used it to replace Mirror on an AddressV125 that a friend gave me! It works normally!
It would be nice if the design was a little more unique or better made!
View detail
Shield mounting Bracket was diverted to extend the Bracket.
[How is it used?
This Adapter was diverted to install a DAYTONA Windshield RS for a Honda Grom on a KTM390DUKE.
Was the one you received as per Image?
It was a good Size to extend the Bracket.
Was the installation difficult?
The Shield is installed in basically the same way as when it is installed on the Grom, but since it was necessary to install the Shield closer to the rear of the vehicle, this Adapter was inserted between the Shield mounting bracket, and the entire Screen was shifted backward.
How was your experience with it?
The Shield did not vibrate violently due to wind pressure even when cruising at 100 km/h on the highway. To be sure, we used Screw lock fluid to prevent the Bolt from loosening.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
View detail
Yamaha's Opposite Thread Screw A must-have for cars
I purchased this product when I switched to Napoleon OnMirror because my OEMMirror was rusting.
The Mirror position is slightly higher, but it was successfully installed.
View detail
Z2 Mirror has ….
The diameter is too narrow and it was not suitable for Z2 Mirror. View detail
Spacer with Opposite Thread Screw
I bought Spacer because I needed to replace RightMirror on my YAMAHA car with Other Brand Product.
When I searched for Opposite Thread Screw Spacer, I found that Large Mortar was a Spacer that converts to Normal Thread Screw→Opposite Thread Screw, but this product is a Spacer that converts to Opposite Thread Screw and gains height as Opposite Thread Screw. This product gains height as it is Opposite Thread Screw.
I found it to be a modest and useful product.
View detail
It's neither good nor bad
Mirror by M-TEC (Shockproof Measured) was installed and when I took it to Plaza for inspection, I was told that it was not covered by the vehicle inspection, so I purchased it.
It is neither too expensive nor too expensive, but the position of Mirror is higher than expected, which is a little disappointing to look at.
View detail
Honda old for VehicleMirror installed on CUBC125 (JA58)
Installed a hand-held old Honda Mirror (8mm positive thread)
OEM 10mm Mirror with reverse thread 10mm Handlebar side with positive thread
So I looked for an Adapter with 8mm Mirror side positive thread and 10mm Handlebar side positive thread.
Equivalent to Tanax CM-2 Easy to install, just remove and replace OEM
I like it because it looks Classical.
View detail
Good product
The MRMirror I own has a footing Plate B Type and I have just purchased this product to install on my ZrX400.
The price is high, but the accuracy is perfect because it is a dedicated product.
View detail
Conversion fixed
The Fixing Screw diameter of the Mirror I tried to install seems to be different, and I wanted to fix it with M10→M8.
The price is not too expensive, the size is not too large, and it can be fixed in a good way.
View detail
Body side Opposite Thread Screw 10mm/Mirror side Opposite Thread Screw 10mm
When I installed DAYTONA's Screen on KTM DUKE200, the Bolt was by Masane, and I couldn't get it on without Adapter, so I bought an Adapter Set of Normal Thread Screw→Normal Thread Screw for Left Side and Opposite Thread Screw for Right Side. I bought Napoleon's Adapter Set of Screw→Normal Thread Screw, and Mirror was bolted to the Screen stay.
The screen is removed and the Mirror is directly attached, and the Left can be used, but the Right cannot use the adapter of the Opposite Thread Screw→Normal Thread Screw, and the Opposite Thread Screw→ is required. However, it is not available in Napoleon On. However, Napoleon On does not have it, and this is the one I found when I looked for it.
It's very convenient to return by Rose!
The left is 20mm for Napoleon On and 18.5mm for this product, but this is an error. The difference at a glance is that the Napoleon-On is a 17mm spanner and this product is a 14mm spanner.
View detail
Rose is for sale.
When I replaced the mirror, I didn't want to see the OEM PlatingScrew sticking out of the cover, so I bought this one, which was sold by Rose, because Napoleon On does not have both forward and reverse. It is a problem. View detail
Adjust Mirror position
Spacer is included to accommodate multiple handlebar diameters.
Because of the Spacer of the genus Gold, it may damage the Handlebar in some cases.
Convenient for adjusting the angle and position of Mirror.
View detail
Useful accessories
There would be interference if I directly install TANAX AOS4 rearview mirror on my motorcycle, so I also bought this TANAX heightening screw accessory, which can be perfectly installed. Although it is a small accessory, the workmanship is fine without burr, which is very good. View detail
For Mirror Replacement
I purchased this product to replace Mirror on my SR400.
It inevitably stands out because of its height…
View detail
Elimination of long-standing problems
Product Name
MirrorOffsetHolder for 10mm
Item Number
27292419
Vehicles
Grom (JC61)
Number of man-hours
Around 20 minutes
Required Tools
Torque wrench, Hexagonal socket, Combination wrench, Pliers system
Why did you choose this product?
There were other products that extend the length horizontally, but this was the only one that also extends the height. Also, it was available in black and looked luxurious. Also, I had a feeling of trust in the product because Grom's name was mentioned in the Impression section.
Was the one you received as per Image?
It was just as shown in the Image. It looks good with a sense of luxury.
Was the installation difficult?
It was easy:just remove the screw, select the size screw that fits the screw hole, and install it.
How was your experience with it?
The long-standing problem of not being able to see Mirror has been resolved. I was worried about not being able to see what was going on behind me, and I felt it was a hassle to bend my elbows every time I had to do it. It was also very easy to install the pons without changing the position of the wiring such as throttle wire.
[Included Parts:were they on?
There were some things written on the documents etc., such as screws.
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Only Yamaha can do it.
Since RoseRose is the way to sell Mirror by Manufacturer, I would like Adapter to think of various combinations and sell them as well. View detail