Reviews
Good position
I came across this product after doing a lot of research on the height and width of the Japanese Vehicle Inspection Correspondence on the CB750rc42.
The width is the same and the height is about 35mm higher than the other two, so I asked the shop that installed it to check if they had done the same thing and since it was compliant, they installed it without refusal.
Extension Harness was also prepared in case, but it was used only for Blinker switchWiring extension.
For this level of uplift, it would have been more cost-effective to just extend the Blinker switchWiring than to purchase Extension Harness.
The position is only 35mm up, but it feels much higher, and the handlebar feels a little tighter in the front, so it is very easy to drive.
It is as easy as if it were a learner's car, but the system is also very windy as it approaches vertical.
I am self-satisfied, but it was a good decision to replace it because it is totally easy to drive and maintain a non-fatiguing position.
View detail
My back doesn't hurt anymore.
I had back pain when riding FXDR114, but after changing Handlebar, long distance touring is also light. View detail
It's best.
Transforms into a classic look.
The driving position is very comfortable and stable.
Even if you drive for a long time, it will not put any strain on your body.
Handle replacement can be done quickly if you purchase the Hurricane extension harness together.
This is one of the customizations I am most satisfied with. -------------------------------------------------- -------- Transforms into a classic look. The driving position is very comfortable and stable. Even if you drive for a long time, it will not put any strain on your body. Handle replacement can be done quickly if you purchase the Hurricane extension harness together. This is one of the customizations I am most satisfied with. Powered by Google Translator
View detail
be quick to react
Quality and texture information Cool with aluminum cutting be quick to react to the feeling of use to find fun in driving An impact No. 1903-N is required by holding the ANEX screw for installation. There is no instrument panel screw groove Cost performance and comparison with other products are said to be expensive, but it is worth it Delivery and packaging to WeBike in a week The packaging is great A caveat is that the seat position changes. You have to know that and buy it View detail
Comfortable with easier Position than OEM
I felt uncomfortable with the OEM's too-wide handlebar, so I replaced it.
The Handlebar of the Cafe is narrower than the Z900RS, though,
The OEMHandlebar is so wide that you would think it was a STREETFIGHTER-type Handlebar, and it stiffens your shoulders.
The position that comes 3cm in front of the OEM by 3cm up with the width shortened by about 6cm will be a much easier position than the OEM.
I would not say that installation is difficult, but if you are not used to it, there may be a Large change.
The handlebar periphery is removed and replaced via an adapter since the diameter is narrower than the OEM.
This adapter gapes when the handlebar angle is adjusted, so it is necessary to check when tightening.
Also, when tightening the Handlebar Post, Brake Holder, and Clutch Holder
Be sure to tighten from the top and adjust the tightness on the underside, so be careful.
The LeftRight Switch Box and Accelerator WireHolder have pre-drilled holes, so no drilling is required.
OEM wire ends when replacing the supplied Clutch Wire. (Engine side) It is recommended to use Tie Wrap or Needle Goldetc. to tie the new wire to the OEM wire and pull it up so that it can be replaced through the same place as the OEM wire.
View detail
Fits: HONDA CB250R, HONDA CB125R, HONDA CB300R, HONDA CB150R
HURRICANE BMConti Type 3
With the NORMAL handlebar, my wrists were a little too far away from the handlebar, so my wrists were easily fatigued, but after replacing the handlebar, my riding posture became easier even in the middle of touring.
Quantity Handlebar:Pair (for Left and Right) The handlebar is slightly raised to prevent fingers from being pinched.
View detail
Maybe a little wide.
OEM was far and low and had to be replaced.
Accelerator Wire was easier to install than MT09, but
The air drainage of the brake hose and clutch hose was Large strange.
The fit feels a little wide.
View detail
Handlebar Straying
I changed a lot of things with EFFEX→Archi→BEET→Condor→Conti2.
I write this only as a personal opinion.
EFFEX→not much different from NORMAL and tiring.
Archi→ easy to ride but not great looking.
BEET→ easy to ride, but forward leaning is tiring.
Condor→ Easy to ride, but I don't like the way the Clutch Cable hits the Meter, doesn't look good in a bikini.
Conti2→A little higher and A little tighter than BEET, but still tiring after a long ride.
Now I plan to try European1 type.
View detail
When you buy a motorcycle, start by replacing the handlebars!...
The cb1100ex's stock handle position is a very uncomfortable and ambiguous riding position.
Also, because I have a cervical disc, I have to lean forward a little and the weight of the helmet puts a burden on me, making it uncomfortable for long distance riding.
However, if you replace the handlebar with this handlebar, the position changes to almost 90 degrees and there is no strain on your arms or shoulders.
cb1100ex absolutely has this handle. -------------------------------------------------- -------- CB1100EX's genuine handle position is a very uncomfortable and ambiguous riding position. And because I have a neck disk, I bow down a little bit in the future. However, if you replace it with this handlebar, your position will change to 90 degrees and you will not be overwhelmed by your arms or shoulders. CB1100EX is unconditionally handle. Powered by Google Translator
View detail
Long distances are now easier.
It was a HURRICANE European2 type Handlebar, but I wanted to make it a little wider, so I changed it to a Z2 Type.
I have only been out for Touring once, but it was easy Touring down the road for about 200 km.
We asked Shop to do the installation and are satisfied with the careful work.
View detail
It's very nice handle for FXDR114
Thank you very much for delivering the goods to my relative's house in Japan, Rider in Korea! 。 I'm going on a trip to Japan next month and will bring it with me to install it. 。 It looks great in the wearing photo on Site. View detail
Cheap!
If you want to buy OEM, Type is enough!
I personally like it!
Handlebar bosses are not used because they are scary.
View detail
To replace the Handlebar on a 2021 MT-09SP.
I wanted to do something about my wrist getting sore in the second half of touring. and hanging angle of the handlebar? I wondered if it was a problem with the handlebar's aperture and hanging angle, so I installed this swallow-type handlebar, which was sold exclusively for the car model.
Clutch Cable is a special product for installation (this is Quantity):Before pulling out the old Cable, fix the lever side of the new Cable to the lower end (ClutchCase side) with a Tie Band as shown in the 5th image, so that you can pull out and turn the Cable at the same time. You can kill two birds with one stone.
The OEMClutch Cable is fixed behind the Headlight, so it is a little troublesome to remove the fixation here.
The HandlebarBody can be installed without any particular problems, and our vehicle has the Handlebar Post position lowered by 3cm, but even when installed at the desired angle, it fits without interfering with the LimitTank.
The replaced clutch wire must be secured around the handlebar with a tie band or it will interfere with the meter.
As for the position, it was slightly difficult to raise the Shift Pedal because it was tilted forward so much, so the pedal angle of the Rear Sets was adjusted.
Also, I went on a Touring trip of about 300 km after the Handlebar replacement, and I felt that it turned out well for me because I became more conscious of my Knee grip so as not to hold the Handlebar down.
However, due to the fact that it was my first touring in a month and my usual lack of exercise, I ran out of energy in the latter half of the day and had to hold down the handlebar more often, so my shoulder area was sore the next day.
(The pain in my wrist was the same, so I think it was caused by the way I hold the handlebar.)
Also, this is not an issue with the MT-09SP, which is a NAKED model with a MOTARD or STREETFIGHTER-like position, but when riding on the highway with a headwind or when overtaking, the air resistance is large or it feels like it is going to float. When the air resistance is large or it feels like it is going to float up when there is a headwind or when overtaking at a temporary court speed+α, and when I get down, the high position of the handlebar made it a very hard position to be in.
Lastly, the position of the handlebar is a matter of personal preference, so it is difficult to judge the position of the handlebar from the values on the product page alone without actually seeing it installed.
View detail
Amazing retro look
Original parts are the best and through Webike great service. Looks great on the motorcycle and really improves the style. More upright and excellent handling. View detail
Fits: KAWASAKI NINJA400 (2014-), KAWASAKI NINJA250R
NINJA400 (2018-) Handlebar Up Type (HURRICANE)
[How is it used?
Touring once a week is definitely easier than Separate handle!
Was the one you received as per Image?
As per Image, quality is good.
Was the installation difficult?
I left it to Shop. 16,000-17,000 yen for the labor.
How was your experience with it?
Anyway, it is easy to ride.
[Included Parts:were they on?
There are no deficiencies in Included Parts:, but the Bird end must be purchased separately.
[Was there anything that disappointed you?
None, low stock, so buy early.
View detail
z900rs only
When choosing a handlebar for the z900rs, I compared six HURRICANE handlebars in person and decided on the Conti2 model.
I am very grateful that HURRICANE has so many varieties to choose from, and I can choose according to my taste.
The mounting holes were also neat.
I have long arms, but it is much easier to ride from the OEMHandlebar. I wish I had changed it sooner~.
View detail
Best position.
Best position. View detail
Hurricane handle type 002
hurricane handle
The 002 type is really good value for money.
It is painted black and the color matches the bike well.
There is no problem in assembling because the machining holes fit well with the parts attached to the genuine handlebar.
If the left hand grip does not come off well during genuine disassembly, try removing it after applying lubricant. And the genuine handle end can be recycled with just an anchor type bolt.
After installation, the position is comfortable. It seems to be more advantageous at high speed because it is slightly bent and the handlebar width is smaller.
I am very satisfied with the value for money at this price.
thank you -------------------------------------------------- -------- Hurricane handle 002 type is really good. Black painting and the color goes well with the bike. The processing hall fits well with the parts attached to the genuine handlebar, so there is no problem in assembling. If the left hand grip does not fall well in the pure disassembly, try to remove the lubricant. And the genuine handle end is recycled with the anka type bolts. After mounting, the position is convenient. It is slightly leaned and the handle width will be smaller, so it will be more advantageous at high speed. The price is so good at this price. thank you Powered by Google Translator
View detail
NORMAL is not possible.
The width and height of the OEM is impossible.
In city traffic, you'll probably hit a car one day with a piece of shavings.
Together with Short mirror, the width of the car is drastically reduced.
I have to change the structure for inspection, but I don't intend to change it back to NORMAL.
This Handlebar is NORMAL and good for hanging.
Kawasaki can make it an Option at the time of sale, and you can get the car's inspection certificate.
No width change would be necessary.
Why do you choose the Tono Position, even if it is Meguro?
View detail
A very comfortable position
Originally, I was going to replace only the handle, but when I measured the height of the desired position, it was an ambiguous length.
When I looked at the length of the genuine cable, it was ambiguous.
I replaced the steering wheel and cables with Hurricane products.
The throttle body work was so difficult that the worker declared that he would never accept the cb1100 again. :)
Everyone is saying the same thing.
It is a position where the waist is erected, but it is quite comfortable. Instead, if you don't have experience on a bike, you'll have a hard time making a U-turn. ---------------------------- Originally, I tried to replace the handle, but I measured the height of the position I wanted. I saw the length of the pure cable and the length was ambiguous. I replaced the handle and cable with a hurricane product The throttle body work was so hard that the worker declared that he would not receive the CB1100 again. :) Everybody sounds the same. It is a position where the waist is built, but it is quite convenient. Instead, if you do not have a bike experience, it seems to be a bit difficult for the U-turn. Powered by Google Translator
View detail