Reviews
ส่งเร็วทันใจสินค้าสมบูรณ์แบบไว้ใจ webike อุดหนุนตลอดครับ View detail
Very comfortable to grip and durable.
I used it on a CUB that I made into a Bar handle.
Until then, I had been using KITACO's TZ Type, but my hands were still sore. I think it is not only thin but also not suitable for Small Engine Displacement Volume vehicles like CUB, which always have to be twisted to a large amount.
So, we used this classical type. I had originally wanted to use this Jack Hammer type, but I was hesitant because it has no flange, it is too long for Small Type Motorcycle, and it is only for 25.4mm Inch bar.
I was also wary of thicker type grips because the Barrel type grips were also very tight in my hands.
There are no basic installation problems.
Since the length is too long for the CUB of the bar handle, we cut it at the border between the vertical rib and the flat part, packed about 1.5 cm, and glued it together.
It is a vertical Rib, so it is not noticeable when cut.
The comfort is great, no fatigue at all. I never get tired at all, my hands get sore after 40km with TZ Grip, but with JackHammer I don't get sore at all even after 200km.
I thought the fatness might tire some other part of the body, but not at all. The nightmare of the old Barrel type has been blown away.
The lack of a brim is not a problem, in fact, the brimless version might be more flexible in the position of the hand and less tiring?
It is also very durable and shows no signs of wear or cracking even though it has been used for a considerable number of years and distances.
The end part seems to be sticking out a bit recently, but I don't mind.
I want to put it on my SR because it is so good. I have a Superbike Grip on my SR, and it works fine, but I'm not sure if it's a good idea.
If I may say so, it would be better to have a 1 to 2cm shorter version from the beginning. It is too long even for normal motorcycles because it was originally designed for big Americans.
View detail
Reduced vibration sensation
Replaced from YB125SP OEM.
With OEM, we replaced it with this Clip to deal with the vibration when the Speed continues over 60km.
It is comfortable to the touch even with bare hands and does not slide around too much even with gloves, so it is very easy to use.
The crucial vibration is also clearly reduced compared to the OEM, and the effect is likely to be felt even during long hours of touring.
View detail
Finally.
I finally found a diameter for the inner pipe of the Hyslow that fits well.
Finally, I was able to put the grips on.
I've been using this grip for a while now.
And it's easy to grip.
It doesn't seem to be as sticky as OEM.
View detail
Supper Grip
I think the cosmetics are good. It is a consumable item, so I think it is inexpensive. View detail
Pretty good
Anyway, Parenthesis is good
It looks like YAMAHAOEM and is the best.
View detail
The Grip is slimmer and easier to drive and operate.
[How is it used?
Replaced with Handlebar.
Was the one you received as per Image?
It is made by Honda and the texture/material is excellent.
Was the installation difficult?
I asked Right-arm in Nishi-Tokyo City, and I feel safer asking PRO to do it.
How was your experience with it?
It is slimmer and easier to grip than VmaxOEMGrip.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I asked PRO to install it, so there is nothing special about it.
View detail
The Grip is slimmer and easier to drive and operate.
[How is it used?
Replaced with Handlebar.
Was the one you received as per Image?
It is made by Honda and the texture/material is excellent.
Was the installation difficult?
I asked Right-arm in Nishi-Tokyo City, and I feel safer asking PRO to do it.
How was your experience with it?
It is slimmer and easier to grip than VmaxOEMGrip.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I asked PRO to install it, so there is nothing special about it.
View detail
Buy extra for free shipping
Purchased this for my NSR50 that I am currently Restore. I will not need it for a long time, but I bought it in advance to get free shipping. I will need it sooner or later and the cost is good, so no problem. View detail
Slim and easy to use
I bought it because I want to be thinner than OEMGrip.
It is too much trouble to process to install on OEM Throttle cone, so it is changed to YamahaOEM.
(Cutting is required for the center rib and the circle part.)
(YamahaOEM is a bit High Solo compared to OEM. Winding diameter 33→36)
The product description says the total length is 126mm, but in reality it was a little over 124mm.
(Note that for some car models, this few millimeters will create a gap.
OEM is 120mm, so I cut the inner Rib and it was Limit.
(Wiring is done by pushing in with air and not using Bond when installing.)
It is comfortable to use, but it is slimmer and more direct as I had hoped.
The thinner rubber thickness of the slimmer model seems to increase vibration slightly, but it is not enough to bother me at times.
Personally, I would prefer the letters DOMINO to be a little more Small Sakura Slit.
Wiring halls are located at both ends, so they are taken to the lower side for installation.
I don't know how durable it is yet, but it is easier to operate and it was worth the change.
View detail
Thank you very much
I have just received the product.
Thank you for your very good response.
We look forward to working with you again next time.
View detail
Great cost performance!
I was looking for a Grip to install on my WhiteBlueGLADIUS650400 and found this.
The straight line design fits well with GLADIUS 650.
The grip is nice and moderately soft.
I have not run the distance yet, but I think it could be compared to PROGRIP.
This is a satisfying experience for a purchase price of a little over $1,000.
I can recommend it
At any rate, I have ordered another pc. in a different color.
View detail
Parenthesis good!
The grip is also easy to grip, and even if you buy it for its design, Large is very sturdy!
The texture and quality are totally good.
View detail
KIJIMA
Grip is the one! This is the one to choose! View detail
Better than OEM Product
The grip is more comfortable than HondaOEM, which looks similar to this Grip.
HondaOEM was having trouble with the surface becoming smooth after about 1-2 years. (The hand slips out of the Handlebar during acceleration.)
It is very soft and good in the beginning...
Other OEM chick Other Brand Products are slightly shorter in length...
This Grip was OEM looking, firm and comfortable to grip, and just the right length!
I'm so glad I bought it!
View detail
Fits: KAWASAKI GPZ250R, HONDA CB500F, HONDA PCX150, KAWASAKI Z250FT, YAMAHA MAJESTY250(ALL MODEL), YAMAHA MAJESTY250C(ALL MODEL), YAMAHA FAZER(ALL MODEL), YAMAHA TREET(ALL MODEL), YAMAHA DIVERSION(ALL MODEL), YAMAHA SEROW(ALL MODEL), YAMAHA GRAND MAJESTY(ALL MODEL), YAMAHA Axis(ALL MODEL), YAMAHA Zr(ALL MODEL), YAMAHA YZF750R(ALL MODEL), YAMAHA YZF-R17(ALL MODEL), YAMAHA V-MAX(ALL MODEL), YAMAHA T-MAX(ALL MODEL), YAMAHA FZX250(ALL MODEL), YAMAHA FZr500(ALL MODEL), YAMAHA DT200(ALL MODEL)
The size is just right and the texture is good.
Used in 2008 YZF-R1.
LengthSize is also really Exactly.
I did not originally intend to use parts cleaner, but I was able to get in without any difficulty without using Bond paint parts cleaner.
View detail
Wiring
I was looking for a wiring grips for a 120mm length Φ22.2 Handlebar and found this product. I was also interested in the new material Elastomer, which combines the best features of Rubber and Plastic, and decided to purchase it. View detail
Rossirespect
[How is it used?
I always put this Grip on my vehicle for On. I have no complaints and Rossi loves it.
Was the one you received as per Image?
I received a Grip that I am familiar with because I use it all the time.
Was the installation difficult?
Cut and peel the old Grip with Cutter to remove the adhesive.
↓
Degrease and apply reliable and proven Cemedine SUPERX.
↓
Fix with Wire after inserting
I always do this.
As for wire, I am interested in Unit's Safety wire (https://www.webike.net/sd/23616697/) because it does not explode in the tool box.
Wire Twister Pliers (Auto Return Type) This is what I use (). (https://www.webike.net/sd/544991/) It is not a tool that will break, so buy it once and it will last a lifetime, so buy it.
How was your experience with it?
After all, a new Grip is nice. It is a part that is constantly being touched, so it is a good idea to replace it on a regular basis.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Think carefully about what you do with the Wire you tie in Twister. Sometimes I see people who tie their hands in a direction and place that kills them.
View detail
Rossi
[How is it used?
I always put this Grip on my for On Road vehicles. I have no complaints and Rossi loves it.
Was the one you received as per Image?
I received a Grip that I am familiar with because I use it all the time.
Was the installation difficult?
Cut and peel the old Grip with Cutter to remove the adhesive.
↓
Degrease and apply reliable and proven Cemedine SUPERX.
↓
Fix with Wire after inserting
I always do this.
As for wire, I am interested in Unit's Safety wire (https://www.webike.net/sd/23616697/) because it does not explode in the tool box.
Wire Twister Pliers (Auto Return Type) This is what I use (). (https://www.webike.net/sd/544991/) It is not a tool that will break, so buy it once and it will last a lifetime, so buy it.
How was your experience with it?
After all, a new Grip is nice. It is a part that is constantly being touched, so it is a good idea to replace it on a regular basis.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Think carefully about what you do with the Wire you tie in Twister. Sometimes I see people who tie their hands in a direction and place that kills them.
View detail
Good design and ease of use
It was used for YAMAHA's DT250.
The design of this one is a Grip using VINTAGEMotocross, and it looks SO good.
In addition to its appearance, the grip is the most comfortable! The hand does not shake even when driving on rough roads, allowing you to drive with peace of mind.
The other day off-road driving was no problem!
View detail