Reviews
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
First MirrorBlinker installation
I put it on a yzf-25r early model.
Screw holes don't meet at all, so I have to rebuild them.
It must not be done. It is absolutely impossible for an amateur.
View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
CB250R installed.
I installed it on my CB250R. Affordable and easy to see.
It's just right because it doesn't stick in the Motorcycle seat.
View detail
Requires some ingenuity in installation
Quantity:Pair (for Left and Right) The end cap of the grip can be removed by pushing it out from the inside (not by screwing it on), but it is difficult to remove if it is stuck in the grip rubber well.
As others have mentioned, the wire winding diameter of the Throttle cone is about 2mm smaller than OEM, so that part needs to be modified.
I had originally cut and modified PVC Pipe to make it larger in diameter, so I did the same with this one.
The diameter of the part where the Grip Rubber is attached is the same as that of a normal Throttle cone, so it can be used without modification if there is no problem with the Throttle cone being low-slung.
The Left Side Grip was also press-fitted with a Throttle cone, so I was worried about installation, but this one had rubber on the inside of the cone, so it fit the outside diameter of the Millibar as it was, so after peeling off the original Grip Rubber, I lightly tapped it in and it went in. After peeling off the original Grip Rubber, I lightly tapped it in and it went in.
For the power supply, there was an Emon power supply extraction fuse of the same size as the Headlight fuse, so the Cable end of this fuse and the Wiring end on the Heater side were each modified and attached to the Bullet Terminal.
There was no place to install the minus ground, but a regulated rectifier was installed in the front cover, and its mounting bracket was a bare gold plate, so I loosened the bolt there and connected the wiring between the plate and the plate. The bracket was a bare Gold plate, so I loosened the Bolt there and connected the Wiring between the plates.
When the power is supplied properly, the Button glows Red→Green→Blue, so it was also convenient for installation to check whether ACC is energized or not.
The color of the Switch's Lamp is probably set to Red (strong), Green (medium), and Blue (weak) like many other things, but when I ran a test run, I felt that Blue was warmer than Green.
I am satisfied with the Switch as it is easy to operate and has a good texture.
Other reviews said the color of the Switch was Orange, but the one we received was Black.
I honestly did not expect it to be this good from the Body price, so I was disappointed in a good way.
I wish I had purchased it earlier.
View detail
Fits: HONDA CBX125F, HONDA NSR250R, HONDA CBR250R, HONDA VFR400R, HONDA Integra, HONDA CBR400R, HONDA SUPER BOLDOR, HONDA CBR300R, HONDA RVF400, HONDA CB400SB, YAMAHA TZM50R, YAMAHA YZF-R125, YAMAHA TZR250, YAMAHA YZF-R15, YAMAHA YZF-R25, YAMAHA FAZER, YAMAHA FZR400RR, YAMAHA YZF-R3, YAMAHA YZF-R6, YAMAHA XJ6
Installed on yzf-r15 India Spec. 2013 Not very satisfied
The included rubber cap was not usable because it was a size larger than Mirror.
There was not enough room in the loops of the mounting holes, and the Left Mirror was easily attached, but the Right Mirror was attached by brute force.
The Mirror in its packaging was facing the opposite way, so it could not easily be turned 180 degrees when trying to turn it.
Visibility is good.
View detail
Fits: KAWASAKI NINJA2 Helmet50RR, HONDA CB223S, HONDA CB400SF, HONDA GB250 CLUBMAN, KAWASAKI KSR-1, KAWASAKI KSR-2, KAWASAKI ZX-10R, KAWASAKI ZX-6R, KAWASAKI ZX-9R, KAWASAKI ZZR1100/ZX-11, KAWASAKI NINJA400R (-2013), SUZUKI GSX1100S KATANA (KATANA), SUZUKI GSX250S KATANA, SUZUKI GSX400S KATANA, SUZUKI GSX750 KATANA, SUZUKI GSX-R1000, SUZUKI GSX-R400, SUZUKI GSX-R600, SUZUKI GSX-R750, YAMAHA R1-Z
Cospar good
First of all, the cosmetics are good. I have no problem with it. I thought it was a very kind construction with markings to guide the positioning when installing it, but I do not recommend it to those who are concerned about markings. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
quite good shape
Mirror was rusted out and replaced with a more recent form.
The navigation is easy to see and the design of the Mirror makes the vehicle feel like it has been exposed.
There is no runout when driving.
View detail
Fits: HONDA CB900, HONDA CBR250R, HONDA CBR250RRR, HONDA VFR400R, HONDA VFR400R Pro Arm, その他 , HONDA AX-1, HONDA CBR400F, HONDA CBR400F F3, HONDA CBR400R AERO, HONDA FT400, HONDA FT500, HONDA NS250F, HONDA NS250R, HONDA NS400R, HONDA VFR400Z, HONDA VT250F SPADA, HONDA AX-1, HONDA CBR400F, HONDA CBR400F F3
Bolt
Bolt rusted instantly, but otherwise satisfied. View detail
Fits: HONDA BENLY50, HONDA DIO110, HONDA LEAD125, HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X
The atmosphere has changed completely and it has become Sporty!
It is perfect for YAMAHAGRAND MAJESTY, easy to install, no problems, wider field of view, increased safety, and most importantly, Parenthesis is great! View detail
Fits: HONDA BENLY50, HONDA DIO110, HONDA LEAD125, HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X
Prices are low, but
Purchased for the design, visibility and price.
No instruction manual is included, but only a bolt and spring washer are needed for installation.
I installed it on a GSX-S125 '23, but first of all, the bolt hole on the Mirror is too small for the Washer to fit in.
Bolt is too long and Mirror is fixed when installed with Bolt alone.
I had to cut off the screw threads.
Please check the length of the lower hole of the car body to be installed and purchase the product.
View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
Better than OEM
Replaced because OEM is too hard to see. Installation was easy. I can't say how visible the OffsetHolder is since it was replaced at the same time, but it is more visible than the NORMAL. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
grown-up (man)
Replaced OEM for better rear visibility. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
Wider.
Good because the range is wider than OEM View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
Mirror
The Mirror is very easy to read and the large size is very comfortable and satisfying. Thank you very much. View detail
Fits: Others , HONDA glom, HONDA CB125R, HONDA XR230, HONDA XR250MOTARD, HONDA VTR250, HONDA NIGHTHAWK250, HONDA VT250 SPADA, HONDA CB250F, HONDA CB250R, HONDA CRM250AR, HONDA CRF250RALLY50, HONDA CRF300L, HONDA CB400F, HONDA CB400SF, HONDA 400X, HONDA NC700S, HONDA NC700X, HONDA PCX, HONDA FUSION
V125S Screw (forward/reverse) must be confirmed
MyMotorcycle V125S Mirror was selected from the hit items in the search from the state that had been set to
Hit, 10mm Normal Thread Screw But when I actually tried to attach it to the vehicle, I found that it was 10mm Opposite Thread Screw was
By year etc, Positive/reverse." It is always better to check the direction of the Screw on the actual car, as there seems to be
As a result, we purchased an additional Conversion Adapter (at a local store because we were in a hurry).
Quality *2:Because Mirror moves due to running vibration (maybe product difference?)
Visibility *2:Because the cut area of the Fashion oval is less visible than the OEM oval due to the reduction in area.
Design★4:Other Brand:Because the sense of product has been improved.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D Tracker, KAWASAKI KDX220, KAWASAKI 250TR, KAWASAKI KSR110, SUZUKI RMX250, SUZUKI 250SB, SUZUKI HUSTLER, SUZUKI DJEBEL, YAMAHA TW200, YAMAHA XT250X, YAMAHA TT250R, YAMAHA SEROW, YAMAHA XTZ125, YAMAHA WR250, YAMAHA DT50, YAMAHA PW50, HONDA FTR250, HONDA CRM250R, HONDA CRF450
Anyway, it's the lowest price in Fat bar!
I thought I bought the High type, and it says so in the Package...
I have compared it with Landy's Low type, but the height is the same...
Huh? Isn't it low? Something doesn't seem right. 。 It's probably not your imagination.
The handlebar is quite high on the VST250SX, so I managed to install it with three clamp extensions.
This seems to be a bit of a turnaround...
In addition, since there is a hole in the blinker and the Axel collar, I cut it out and wrap a piece of tape used for tennis racket or bicycle grips around it to prevent it from slipping.
It's working surprisingly well.
View detail
Fits: その他 Vehicles with 22.2 mm handles
Could not install...
I was planning to install it on a BMW G650GS, but the Left Side was successfully installed, but the Right Side could not be installed due to interference with the brake hose. I think a large width modification is necessary for installation. I am sorry to hear that... View detail
Design is good, but,
The design and overall construction is good, but I think the quality is commensurate with the price. View detail
Custom Handlebars
This custom handlebar is a perfect addition to any custom scooter build you may have. These are easy to install, excellent quality and functionality. Highly recommend for custom look. View detail
Custom Mirrors
High quality mirrors, highly recommend for styling and customization. These are perfect for that low profile look and function better than stock mirrors. View detail
The supplied hexagonal was licked easily and could not be used because the fixation was too loose even after tightening it.
I wanted to return the product, but the Hexagon Bolt has become so licked that I can no longer remove it.
If I purchase another Handlebar, I will discard this product. I don't need to return it.
It should be possible to fix the Handlebar part by tightening it with a hex, but the quality is so low that the Handlebar moves no matter how much it is tightened, and I will never buy this Manufacturer's again.
View detail