Reviews
Available for frando 7nb
Available for frando 7nb MechanicalSwitch, which has the same structure as brembo.
I believe only frando 7nb is available as a precaution.
The reason is that the current frando's Lineup has changed the SizeSetc.Spec. of the Pipod degree.
Also note that this is not an official usage.
View detail
A necessity for driving on public roads.
Brake switch required when using Racing radialMASTER on public roads.
It requires dexterity and subtle adjustments to install small parts, and you must be able to devise a way to use the device when it does not work well due to individual differences.
Since it is a Mechanical Switch, if it is attached properly, the Brake will turn on without fail and there is no discomfort in lever operation.
View detail
Fits: KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900)
Small processing or required.
I replaced the OEM with this one because it was badly rusted.
I had to shave the stopper on the shaft that goes into the hole on the brake pedal side to be able to insert the split pin.
I'm giving it 3 stars because I couldn't pimp it out.
There is no problem in use.
View detail
Fits: HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA XR50 Motard (MOTARD), HONDA XR50 Motard (MOTARD), HONDA XR400 Motard (MOTARD), HONDA XR400 Motard (MOTARD), HONDA XR250 Motard (MOTARD), HONDA XR250 Motard (MOTARD), HONDA XR250 Motard, HONDA XR250, HONDA XR250, HONDA XR250
Not good
It stopped working about a month after the replacement.
Phenomenon:Stop-lamp is still on even if you don't hold Lever.
It seems to have developed a sticking inside. Lubrication did not improve it.
Well, I've been storing it outdoors with a Cover, and I've been hit by rain a few times …
View detail
Fits: HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA XR50 Motard (MOTARD), HONDA XR50 Motard (MOTARD), HONDA XR400 Motard (MOTARD), HONDA XR400 Motard (MOTARD), HONDA XR250 Motard (MOTARD), HONDA XR250 Motard (MOTARD), HONDA XR250 Motard, HONDA XR250, HONDA XR250, HONDA XR250
Used for Rear SetsRear brake
Originally used for Front brake lever is Bolt On so ginger
Improved Rear brake on Rear Sets and installed it.
Durability is a problem, but the price is cheap so buy again if it breaks.
View detail
![[NISSIN Repair Parts For Master Cylinder] Assembly Brake Switch](https://img.webike-cdn.net/catalogue/images/89338/1_152781278781629200_m_dst9u_l_TS.jpg)
Fits: その他
It is awful.
The appearance is "Well, it's like this" Level.
There is no problem with sufficient mounting accuracy.
, But it was broken when I noticed it in about a week.
View detail
Switch saying that there is a feeling, I do not mind.
I used it for diverting Brembo radial of net for Race to STREET.
There was a rumor that there is a feeling to enter Switch, but I do not feel it in particular.
Although I used it for 5 years, durability was also no problem.
I think that disconnection will not occur if proper processing of Wiring is done.
You can expect much better durability than loading Micro switch etc.
If there was only one difficulty, it was somewhat late to turn on.
As there is nothing compared to others, it may be just an individual difference.
But in the past it was 10,000 yen, but it is half price now.
Of OEM Witch for brembo's commercial car model MODEL, as well as domestic MASTER
Switch is quite expensive, so at this price you can use
Ali will be the choice.
View detail
Brake switch
The installation itself is not so difficult, but it was a little troublesome because it would require adjustment. It looks good if Bolt of Lever pivot looks a little bit better using Bolt. View detail
Fits: Others Radial clutch master cylinder
Would not it be cheaper a bit more?
【What made you decide the purchase?】
Fland - 7 NB Radial master cylinder Left Side (for Clutch) I bought it to install MechanicalSwitch.
【How was it actually used?】
Safety mechanism works like OEM.
【Was it difficult to install? (Hard parts case)】
Easy to do according to installation Instruction Manual.
【Please tell me the point of installation and hang (in the case of Hard parts)】
In order to attach MechanicalSwitch to the Radarphone of Flanders, Koken's for Brembo Radial MasterPush rod Pivot (Material : We need to use Stainless Steel.
[Is there anything I was disappointed about?]
None.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Would not it be cheaper a bit more?
【Have you compared items?】
In order to attach a MechanicalSwitch to the Radarphone Clutch of Flanders, there is no choice as to only use this Switch.
View detail
I bought it for brembo Radio Pong.
I bought it because the Brake switch of brembo Rapon has broken.
Installation is not too difficult.
However, there was a Point where Switch does not work when adjusting Brake position.
It now works when you adjust using Tie Wrap.
It's a shame just because the price is cheap.
View detail
Switch indispensable to the MASTER of a Beringer ... Compared with the Switch of the Radial master of other company, a Cost performance, Design nature, and work are easy, and it is quite good. I think that anyone can perform it easily since attac
Switch indispensable to the MASTER of a Beringer ... Compared with the Switch of the Radial master of
other company, a Cost performance, Design nature, and work are easy, and it is quite good.
I think that anyone can perform it easily since
attachment is attached [ nothing needs to think ] to the screw hole of a MASTER.
Since it has just purchased, about durability, it is unknown.
It seems that it is necessary to bypass in case of 3 pole Switches, such as a Kawasaki vehicle, when using it as a Clutch-master Switch incidentally.
View detail