Reviews
To relocate Rear Master Coupling
[How is it used?
Used to relocate the Rear master on MainMotorcycle's XJR1300C.
MASTER is changed to NORMAL and footpeg is changed to Over's Rear Sets.
Was the one you received as per Image?
It was made just like the Image. I checked the size, etc. on the Active catalog before I bought it.
Since both ends are M6, it was not expected that the one to be co-tightened with the footpeg would need to expand the hole to M8.
Was the installation difficult?
The combination of XJR1300 and Over footpeg can be easily installed if only the holes can be extended.
For the master cup, we recommend brembo's small tank with a 15-degree angled outlet.
How was your experience with it?
The OEM has the Rear Master Coupling in the Side cover, which is very poorly maintained.
I am satisfied with the new relocation, which has considerably improved the serviceability and looks very good.
Also, the side where the Master cup is installed has an M6 tap cut off so that it can be attached to the SMART without using a nut.
[Included Parts:were they on?
I think it came with an M6 Smallest Bolt, and a simple Instruction Manual.
[Was there anything that disappointed you?
If I may say so, it would be better if the Size of the Mount part is not only M6 but also M8 with normal RANup.
Many manufacturers use M8 for Rear Sets, so I think this will make it more universal.
View detail
If Black!
It is used on brembo's Radial brake master 14RCS.
I bought a PLOT Tank BracketBPS002-BB at first, but the rubber hose was bent in the middle. I searched for a lot of information and came up with this product.
This product allows the S-15BTank to be fixed in an almost perfect position and angle, with a very natural bend in the rubber hose.
I have two complaints:I want a black color and the BoltM6×30mm is too short to install on the MASTERCylinder. It is not impossible to install the bolt, but it is necessary to replace it with M6×35mm bolt. (The photo is before replacement).
The color is simply my taste, but I have reduced one star because of the short Bolt.
View detail
![[NISSIN Optional Parts for Master Cylinder] Tank Bracket](https://img.webike-cdn.net/catalogue/daypic140709/49151_1_l_TS.jpg)
Bracket
The no-frills Bracket. Yes, it's a Bracket. View detail
![[NISSIN Repair Parts for Master Cylinder] Tank Bracket](https://img.webike-cdn.net/catalogue/daypic140709/24342_1_l_TS.jpg)
On the Brake Side
When I changed the master tank on the Brake Side of my separate Master Cylinder from a LargeTank to a Small TypeTank for Clutch, the long master stay for the LargeTank could not hold the Master Cylinder firmly in place, and it moved due to vibration. I decided to buy it because the long Master stay for LargeTank could not be fixed firmly and moved by vibration.
I am satisfied with the balance between the clutch side and the appearance of the clutch.
View detail
Front brakes master has been replaced.
Since I had replaced the front brakes master, I was looking for something to mount the reservoir tank without a bracket and decided on this.
It is good because the mounting position and angle can be freely decided.
View detail
Inexpensive and easy to install
I bought it to use with the brembo s50 large oil cup. The installation angle needs to be adjusted by myself, otherwise it will be inclined. It is not suitable to install the original thick gasket when used with the s50 oil cup. The thick gasket will cause insufficient space for tightening the nut at the bottom. It is recommended to use a thin gasket for installation. There is nothing to say about the appearance. Generally speaking, it is a Nice product, simple and easy to install. -------------------------------------------------- -------- I used it to use it with the Brembo S50 oil cup. The installation angle needs to be adjusted by itself, otherwise it will be tilted. It is not suitable for installing the original factory with the use of the original factory with the S50 oil cup. The thick pads will cause insufficient space to tighten the nut at the bottom. It is recommended to use a thin pad. Good products, simple and easy to install. Powered by Google Translator View detail
Texture is good.
Purchased when GALE SPEED's Brake master was replaced.
I put a Washer on my Separate handle because the bottom of the tank hits my Separate handle.
The quality is perfect, but I think the price is too high.
View detail
Although the racing master of brembo was attached, when it was default specification, there was no mirror holder. (Since it is racing specification, it is natural) Since he wanted to carry out as [ come out / if possible / sense of incongruity ], the
Although the racing master of brembo was attached, when it was default specification, there was no mirror holder.
(Since it is racing specification, it is natural) Since he wanted to carry out as [ come out / if possible / sense of incongruity ], the place product made from an antlion which was looking for the near thing of the color was decided on.
The kind of color is also abundant.
(The other company's was only an uncomfortable color ...) The structure of goods is very beautiful and they do not have the color unevenness of an anodized, either.
When it actually tried to have performed radial master attachment, it was comfortable and became natural touch.
the kana it was better not to have a logo mark individually -- I think ...
Although the price thought somewhat high kana, also when seeing the height of the quality of goods, I thought that it was inexpensive.
View detail
Easy-to-use Bracket
After the NISSIN radipon conversion, I was concerned about the included plate Bracket, so I replaced it with this one.
Depending on how you do it, it is possible to bend it much more than you might imagine.
In this case, the surface was twisted 90-degrees, bent 90-degrees, and then bent horizontally with fine adjustment.
As long as you have a long Driver and a suitable rod to use as a fulcrum, I think you can make the angle almost exactly as shown in the Image.
I am satisfied with the product itself, but I guess the only Neck is this Gold amount for a Bracket that also has a Risk of failure.
View detail
Don't use Home center's plate Universal Bracket, use this one.
I bought this as related parts to replace the MT-09's front master cylinder with the YZF-R7's OEM radipon.
Material though Billet:I was worried that it would be soft because it is aluminum. I was worried that it would be soft, but it is harder than I imagined. The bending process is a little Large strange.
Conversely, once the angle is set, there is no need to worry about the product becoming wobbly while in use.
If bent at a sharp angle, surface cracks may appear, but if the bending R is sensible, no Anodized Crack cracks occurred, so it must be a material with some tenacity.
I am not sure about durability (especially UV weather resistance) yet, but since it is a product of FOR JAPAN MODELBrand, I am sure it is made with some consideration. I hope it will not be like Anodized by Chinese Parts.
Plate Brackets with holes in Universals, for example, don't look good, so we want to pay attention to the details.
If it were a little cheaper, I would give it 5 stars.
View detail
for Clutch Master.
I bought these to go with Gail's Clutch master.
There was a Plate type that was a little cheaper, but I dismissed it because it looked like a Bracket from Home center and bought this one that was on a top ranking.
It can be attached to the Mirror Holder.
The texture is elegant and not bad.
The only drawback is that the angle of the Clutch lever is not adjustable, so the Master tank may lean a bit depending on your preference.
And I wish I had Black instead of Plating if possible!
View detail
I wanted Black.
I bought this to go with Gail's Brake master.
There was a Plate type that was a little cheaper, but I dismissed it because it looked like a Bracket from Home center and bought this one that was on a top ranking.
It can be attached to the Mirror Holder.
The texture is elegant and not bad.
The only drawback is that the angle of the brake lever is not adjustable, so the Master tank may tilt a bit depending on your preference.
And I would have liked to have had Black instead of Plating if possible.
View detail
Expensive, but good
For Separate Handlebars, but used for Bar handle.
It's your own responsibility, but it does lean forward a bit, but it's perfect.
But it's a bit expensive, and I can't complain about the small number and variety of products they offer, even though it's just this kind of thing;
View detail
It's expensive, but…
I think it's a bit expensive, but it's a solid product.
Oh, no! That's why it's Large weird to bend!
View detail
![[NISSIN Repair Parts for Master Cylinder] Reserver Tank Bracket](https://global.webike-cdn.net/photo/impression/e5/e5faf9fa45f142d8390014c6360039d7L.jpg)
Fits: Others
safely
I wanted a black one and bought this one.
It's not too bad, but it's not too bad at all.
View detail
![[NISSIN Repair Parts For Master Cylinder] Reserver Tank Bracket](https://img.webike-cdn.net/catalogue/10054/65853_1_TS.jpg)
Fits: その他
Black stands out.
The black color is used to unify the look of this item. The original silver had a floating appearance, so by making it black, it looks tighter and more parenthesis. View detail
![Master CylinderTank Bracket [NISSINRadialfor Clutch]](https://global.webike-cdn.net/photo/impression/97/97e95981651da09fc34271db6e93ec7dL.jpg)
PetitCustom
The bracket attached to the Nisshin radial master was silver. It was good as it was, but I wanted to unify the whole thing with Black, so I changed to Black Anodized. View detail
![Master CylinderTank Bracket [NISSINRadial/Horizontal TypeRadial/Horizontal Typefor Brake]](https://global.webike-cdn.net/photo/impression/cf/cfe5a03b588cb711aebc3a3cadc17392L.jpg)
Fits: Others , Others
The look becomes better parenthesis.
I bought it because I thought a sense of unity would come out in black. Custom but Parenthesis is better. View detail
brembo [Color] SmokeTank (S50) Used for installation
Brembo RCS brake master cylinder and smoke tank (S50) I used it to install the
Smoke tank and 8mm high rubber bushings (POSH H-Shaped Rubber PARTS-NO,100202) The combination of the attached M6x20mm bolts and SPL washers does not allow for the use of the nut Do not use an SPL washer and use a normal thin washer because the cling will be reduced I did
After tightening the stay with the mirror, temporarily place the tank and check the level It was slightly tilted, so I corrected it The correction was done by putting the duct tape on the monkey wrench to prevent scratches
We were able to set up the tank well without being distracting in a good way
View detail
He can bend over if he wants to
The price is high because of the aluminum cut-out, but the reliability of its physical properties is high Outclassing
As you can see in the image, it is rigid even with 90°bend first and then 135°bend with a twist is no problem Moreover, no special tools are used for this bending process All you have to do is put a round steel rod on the part you want to bend and apply force
If you want to bend it, the beautiful anodized material will be stretched and lose its shine You might want to go with Silver (OrangeAnodized was removed by Pipe Man.)
I am satisfied with the finished product It is definitely better than the one with bent planks
View detail