Reviews
Cost performance is high
OEM Bleeder Bolt was deteriorating, so this Material is less likely to deteriorate.:I purchased a TitaniumBleeder Bolt.
The quality is high for the price, and I think the cost performance is very high.
The weight is about half that of the OEM at 3.5g compared to 6g, but for general use, there may not be much difference.
As for the cap, NisshinOEM Product cannot be used due to its slightly long shape, so it must be prepared separately.
For us, the Cap sold at Straight, a tool store, was just fine.
It would be helpful to have more ZETA TitaniumParts in the lineup, as the other ZETA TitaniumParts also have high cost performance.
View detail
Perfect for Repair from NORMAL!
[How is it used?
NORMAL BreedBolt came rusty and Pad pin Material:The Titanium unit was replaced with a Titanium one, so it was installed along with the Titanium unit.
Was the one you received as per Image?
As expected of Material:Titanium! It is lightweight, perfectly accurate, and very beautiful.
Was the installation difficult?
It is only a matter of replacing it with a NORMAL one, but if it is not done quickly, the fluid will leak, so cleaning is essential, including removal of oil.
How was your experience with it?
Check for leaks etc. is still to be done, but it was tightened as Exactly.
I think it looks beautiful and is good for dress-up.
[Included Parts:were they on?
There are no other Included Parts:.
[Was there anything that disappointed you?
If you look closely, you can see what looks like processing marks, but it is not a Level you need to worry about. If I may say so, it may be a little expensive considering that NORMAL is about 600 yen for Steel.
▼ Considering that the OEMBolt rusted out after less than 2 years of new purchase, I think it is a PARTS that should have been put on from the beginning.
View detail
For Gail SPEED MASTER
Bolt was replaced before it rusted.
I think it is cheap for a Titaniumium Bolt
I'm satisfied
View detail
Upgrade that old rusty bleeder screw
When looking at my motorcycle to see what was required to upgrade my front brake lines. Noticed the old front brake caliper bleeder screw was rusty and leaking. So added one of these to the order to swap it out while the brakes were apart. Much nicer fit and finish then the old OEM steel one and do not have to worry about it rusting again. Pricey but to be expected for this material. Straight forward installation just remember not to over torque it at the completion of your maintenance. View detail
Titanium is expensive, but it's good stuff.
The bolt on my GALE SPEED Brake master was rusted out and I wanted to buy something rust resistant.
It arrives without any particular problem. It is natural.
This is a RECOMMENDATION product especially for those who use Gail.
It's Titanium, so it's a bit expensive.
View detail
Self-satisfied
I bought it because Nisshin's Rajpon and Screw Pitch are the same
But when I rubber cap it, I can't see it at all!
It was just an expensive but self-satisfying Custom, who knows?
View detail
Will be installed in W650's OEM Caliper
My wife's W650, Front's OEM Caliper, so it's an M8, Pt 1.25 of this Air You need a breeder
The OEM Bleeder Bolt is corrosive
After removing the air, I use the Tissue as a guide to suck up the remaining Fluid in the hole It will eventually corrode
If that happens, you won't be able to pull the Air out, so replace it before that happens
View detail
To vent the air in Thermostat
When I drained the air from the OEM Thermostat, I got Rust's boiling water mixed in at first Things have come up
Something bothered me, so I took it off and the hole in the air extractor is corroded!
I dipped it in a chemical solution, cleaned it and installed it, but it will probably rust again, so it won't rust I bought this in Titanium alloy gold wood
Clutch, front master cylinder and front caliper The Bleeder Bolt has been replaced with this 64Titanium, but the Rear Only OEM Caliper's AirBleeder Bolt is still OEM, so we'll see Replacement
View detail
High precision
For brembo new Crab 34, NORMAL's BreederValve is head 11 mm or 7 / 16in. The size of nice Size, in addition, because it is brittle and heavy made of iron, it is lightweight about 5 Gram per piece, but I think that the real value of this item is the hardness, high rigidity due to Material, plus the processing precision , The feeling of being tightened after bleeding and the feeling of security are not compare with NORMAL's Breeder, as long as the head is 10 mm. View detail
Apply brembo
Material until Breeder this time : I did not plan to turn it into a Titanium product but another Titanium Bolt from Jita ... Nut I saw it in the eyes and hurriedly purchased
I was glad I could buy it from the conclusion
Well, thanks to this Breeder, I also exchanged the Brake line comprehensively My self satisfaction is 5 stars
View detail