Reviews
GILD Rear Caliper holder for Brembo P2 rear brake
About quality and texture Top quality aluminum bracket. With smooth finishing. The weight feels ok. Not too heavy or too light. It also comes with brembo fiting stainless steel screws. About the feeling of use Looks perfect in silver with my gun metal brembo rear brake. Products to buy together Bought it with brembo P2 with red logo. Item number 20.B852.78 Difficulty of installation Installation maybe shorter if the rear rim is easily removed. The fitting of the rim which takes a while. I replaced my rear hose so the total time about 2 hours. But just fitting the caliper and bleeding the hose maybe just an hour. Cost performance and comparison with other products Price is around slightly cheaper than the other brands but the finish is not short of the others I guess. About shipping and packaging Come in plastic wrap with bubbles wrapping for protection by seller. Shipping cost is not expensive as the item is not very big. Any concerns, cautions, or advice when purchasing The only concern is that the item maybe scratched as it's only cover by plastic but the seller did a good job by protecting it. And the item is made not easily scratch too. View detail
Processing is beautiful
Bolt and Shim will be provided separately.
M10×25?Pitch1.5 and M10×25?Pitch1.25 are available.
The processing is beautiful and the rigidity seems solid.
I would have liked Bolt and Shim to be included if possible.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S
Active Rear Caliper support
Purchased this for the Swing Arm and to replace it with a Brembo caliper. View detail
Fits: YAMAHA MT-25, YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA YZF-R25
On the 2020 R25.
I put it on my R25 with Inverted Front Fork normally without any problem.
The durability is unknown, but the construction is solid, so it should be no problem. I am satisfied.
View detail
Fits: KAWASAKI ZX-14R
Sale item was cheap.
For a little over 10,000 I was able to buy a Support for the new ZX-14R Crab.
This is an unbeatable price
OEM is weak, so the new Crab and Gale's Small diameter MASTER.
Increase braking power.
View detail
Fits: KAWASAKI Z, KAWASAKI Z1, KAWASAKI Z2
SSItoCaliper support
The installation was very easy, as the center of Caliper came out without any fine tuning using .Shim because of the good accuracy of Support.
The included Bolt also has a hole drilled for wiring, so wiring comes out as it is, so it is a recommendation.
View detail
Fits: YAMAHA FZR750R, SUZUKI GSF1200S, SUZUKI GSX1300R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, HONDA CB1300SF, SUZUKI TL1000S, SUZUKI TL1000R, SUZUKI GSX-R400R, SUZUKI RGV250Γ, SUZUKI RF900R, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GS1200SS, SUZUKI BANDIT400
You can trust me.
I bought it from another Motorcycle and had no problems, so I trusted them. View detail
Fits: HONDA CB1300SF, HONDA CB1300SB, KAWASAKI ZrX1200DAEG
Beautifully made, perfect fit.
I'm really happy with the quality of these parts, they fit perfectly and look beautiful, they really add to the high quality look I was trying to create with Öhlins forks, Dymag carbon wheels and AP Racing calipers, Superb service from WeBike. View detail
Fits: HONDA CBR600F, HONDA CBR400RR, HONDA CB750, HONDA CB400SF, SUZUKI IMPULSE400S, SUZUKI IMPULSE400, SUZUKI RF400RV, SUZUKI GSF750, SUZUKI RF400R
Match CB1100 Fork with Initial ModelABS.
[How is it used?
The normal fork of CB1100 except RS has a caliper pitch of 62mm and 80mm. This item is for CB750 (RC42 ) It corresponds to 80mmPitch as well as etc.
The caliper side is compatible with bremboAxialCaliper 40mm.
Was the one you received as per Image?
The product seems to be Active and is working well with no accuracy or quality issues.
Was the installation difficult?
It is a Bolt On, so it is easy to install. In my case, there was a slight interference between the Caliper and the disc mounting Bolt base of the Wheel, but I was able to get it out by shifting it slightly.
How was your experience with it?
Since the Caliper position is at the top compared to the Fork of the 62mmPitch, it can go without the Hose extension. It also looks more natural.
[Included Parts:were they on?
In addition to the Instruction Manual, Bolt and Shim are included.
[Was there anything that disappointed you?
The quality of the product is not particularly problematic, but the high price is disappointing.
The recent price increase due to price revisions has made it even more expensive.
The same manufacturer's support with a 62mm pitch is often available, but the 80mm pitch one here may be special and is not available at all in the second-hand market.
View detail
Fits: HONDA CBR600F, HONDA CBR400RR, HONDA CB750, HONDA CB400SF, SUZUKI IMPULSE400S, SUZUKI IMPULSE400, SUZUKI RF400RV, SUZUKI GSF750, SUZUKI RF400R
Fits front forks with CB1100 ABS of some years.
[How is it used?
I purchased the Fork/Caliper pitch 80mm/40mm to fit an older CB1100 Fork with ABS.
Was the one you received as per Image?
Quality is as high as the Image.
Was the installation difficult?
Basically Bolt On, but if it has ABS, it is better to install in Shop to make it work properly.
How was your experience with it?
It is well made and feels secure. I think it is indeed Active.
Recently, CHINA products have been distributed, but there are some cases where the products cannot be installed due to insufficient accuracy or defective products.
[Included Parts:were they on?
It comes with Bolt and Shim.
[Was there anything that disappointed you?
None in particular. Satisfaction level is high.
▼ CB750 (RC42) It is the same pitch as the Fork of the STD Disc and fits the diameter of the STD Disc.
View detail
Fits: YAMAHA FZR750R, SUZUKI GSF1200S, SUZUKI GSX1300R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, HONDA CB1300SF, SUZUKI TL1000S, SUZUKI TL1000R, SUZUKI GSX-R400R, SUZUKI RGV250Γ, SUZUKI RF900R, SUZUKI GSX-R750, SUZUKI GSX-R750, SUZUKI GS1200SS, SUZUKI BANDIT400
That's what Active is all about!
I purchased ActiveSupport along with my brembo equipment. I personally like this manufacturer and the quality and price are very attractive. I am very satisfied with the center and the quality of the product. It may be a little expensive, but it is a product that you can be satisfied with once rather than losing money buying a cheap one. View detail
Fits: KAWASAKI ZXR750R, KAWASAKI ZXR750R, KAWASAKI ZXR750, KAWASAKI ZXR750, KAWASAKI ZX-9R, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI ZEPHYR400X, KAWASAKI ZEPHYR1100, KAWASAKI ZZR400, KAWASAKI ZZR1100C, KAWASAKI ZZR1100D, KAWASAKI ZX-9R, KAWASAKI GPZ900R
Purchased for installation of Brembo caliper
I bought this product to install Brembo caliper. The texture is good.
RightLeft and backside engraving for installation (Landmarks) It would have been nice if there had been a detailed Instruction Manual that would have helped me understand the installation orientation. I had a little trouble installing it. (Is it just me?)
View detail
Fits: KAWASAKI Z1, KAWASAKI Z2
For Upgrade of Normal caliper
Converted from KawasakiZ1 OEMCaliper support.
Quintessential Over.
Aluminum Cut-out texture is the best finish.
We chose Silver to be One point.
The pad moves smoothly because the pad entry point has been polished. I use this pad with Vesra's Shim pad, and there is no squeal at all.
If you want to use double diskSpec., you will inevitably need two of them, but two Supports will cost 50,000 yen over.
It is a fun part, but it is a very satisfying part.
View detail
V-max 1200 Rear Brembo caliper support
V-max 1200 Rear Brembo caliper support. Perfectly compatible with Brembo 2p calipers. It is also an overlacing product. View detail
Fits: HONDA Rebel250 S Edition, HONDA Rebel250 S Edition, HONDA Rebel250, HONDA Rebel500, HONDA Rebel250
For REBEL.
WR3 is cheaper, but after reading the impressions, I decided to go with WR3.
I can use it without problems
View detail
Fits: HONDA Rebel 500, HONDA Rebel 300, HONDA Rebel 500, HONDA Rebel 300
For REBEL 250.
OverRACING is expensive, so I bought this one.
The 250 can be installed and used without any problem.
View detail
Excellent Craftsmanship
Took about 1 week to arrive. Compatible with my 2005 Vtec III. Looks and feels great! Highly recommended product with excellent craftsmanship. View detail
Fits: YAMAHA WR250R
Wheel replacement for X
CarRear support needed when replacing WR250r with XWheel to make it MOTARD.
I was able to order OIL and other parts together.
View detail
Complete Diversion
Purchased as a support to put Crab type Brembo on Takekawa's φ27Front fork. From OthersManufacturer, let alone Takekawa. Mukawaφ27for Front ForkCrabCaliper support." One-off is another option, but one-off is quite expensive. The offset to the Fork and Rotor was adjusted by Washer and Shim. The offset to the Fork and Rotor was adjusted by Washer and Shim. View detail
Fits: HONDA CB750 FA (RC04), HONDA CB900 FZ (SC01), HONDA CB750 FZ (RC04)
For brembo installation
Brembo caliper, SUNSTAR 320mm, radipon to strengthen the Brake! View detail