Reviews
Maybe a little longer.
The length is so long that it is kind of unsettling. I feel like it could be 5 cm longer. View detail
Fits: KAWASAKI SUPER SHERPA
Bolt On by Limit Car Type
I purchased a SUPER SHERPA specific Brake hose for front and rear.
Banjo angles are not good, both front and back, like NORMAL.
It was impossible to install Hose in Line.
One more thing, you can specify the color of the hose, but the Banjoetc.
The color of the bracket cannot be specified, and the colors of the front and rear banjo are different,
There is no unity.
Is this how it is with out-of-print for-vehicle parts management?
But I managed to attach it and it's not inferior in terms of functionality,
I am going to use it for this.
View detail
Fits: HONDA CB400 Fore (air-cooled), HONDA CB400 Fore (air-cooled)
Photos on the website are not good.
Listed photos are in Quantity:Seems like 1 Set of 2pcs.
You can choose for F1 or F2, but the only difference is the length of the Quantity.:It was not a Set product.
OtherManufacturers are listed at 1 pc, so you should do so.
Easy to make mistakes.
View detail
Fluid is slightly blotchy….
I wanted to make the crossover type of Swage linePRO into an h-shape and shorten the hose length as much as possible, so I purchased this GOODRIDGE 160mm and 310mm hose and a T-shaped 3-way Fitting Adapter.
However, I was so traumatized that I could not remove the air from the OEM Master Cylinder, and I wanted to reduce the air removal work as much as possible, and I was tempted to remove the Caliper and wash it in the washroom. I wanted to reduce the amount of air venting work as much as possible. (It was too expensive and the quantity was too high).:2pc. Set can't be bought either, so only 1 pc. …)
However, due to the fitting, it was not possible to make the "h" shape, which was the original goal, and the 310mm Hose and 3-way Fitting Adapter were not used.
The installation was completed without any difficulty, and after bleeding the air, we went for a test run to confirm that the brake was working properly.
When inspecting the Hose area after the test ride, is the Hose fitting on the underside of the Stoveli wet?
At any rate, I wiped it off that day and checked it about a week later and found that the fitting was still wet, so it might be Overtorque, but I retightened it and left it again.
I gave up because the Fluid still oozed out of the Fitting.
*I think it's usually NG, but it's not like it leaks, it's more like it seeps, so I always inspect it before driving.
At first, I was afraid that it was leaking from Stoveli, but there was no Fluid adhering to the Connector, and Fluid was adhering from the Fitting of the Hose connected to the Stoveli, and it seemed to be slightly seeping from the Fitting on the Caliper side, and after driving, the Dust seemed to be adhering as shown in the image. After driving, it seems that dust is adhered as shown in the image.
The Swage line installed on the upper side of the Stove top is not seeping, so I would like to change it to theirs, but the minimum hose length is 20cm even with Easy order, so I would like to leave it as it is for a while, and if the symptoms worsen, I would like to take measures.
By the way, I used this GOODRIDGE Hose on another vehicle and it never bled, so I'm sorry to hear you pulled a HaGap.
View detail
![Vehicle Exclusive Rear Brake Hose [HBF1056]](https://img.webike-cdn.net/catalogue/images/52568/FPS03_K0001_TS.jpg)
Fits: DUCATI M900 Monster 1993-1999
About the Banjo Angle
I don't know about the overall evaluation of the component as a whole, as I haven't used it yet. The Banjo itself has a slightly different angle, but more importantly, the angle of the Banjo's Crimp to the Hose is not as flexible as it should be, as the Hose itself is very rigid, and the Hose cannot be installed as OEM. View detail
Brake hose
In the picture of the purchased item, Quantity:It shows 2 pcs, but when I received it, only 1 pc was included.
Please indicate what the enclosed product contains in the product introduction section.
View detail
Not good
I bought this for my WR250R, and I'm very happy with the Banjo
I bought a 90-degree Banjo-Bolt and a SIDE 20-degree Facing Left for the Adapter, and it works perfectly.
View detail
Torque management in Aluminum is a moot point.
Junction between Banjo adapter and Hose in Aluminum (Taper section) s Torque management was difficult, and although I tightened it up to 8 to 10 Newtons and as the instruction manual states I'm not a qualified person, so I'm working at my own risk. Because I am not a qualified person, I am working at my own risk. I did not know that the torque management of aluminum is so difficult. I've made two banjo adapters out of the box, so I'm going to have to take them to a motorcycle shop to be replaced. I asked for it. Critical security components rely on qualified personnel. View detail
Bolt-on Kit by vehicle type ???
Product creation etc.. I think that it is solid..
However, despite singing as a vehicle type Bolt - on Kit,
I will not do it properly as it is.
I do not know whether the design of Kit is sweet or a strategy for buying additional parts,
If you come to a vehicle inspection in this Kit only condition, I (Ex inspector) If it is not conformity certificate.
Is Motorcycle supplies such a thing natural?
It happens to be only for our model.
I think the product itself is not bad.
View detail
Not good
Even though it is different depending on the model, Hose is a little short, like NORMAL
It is slightly hard to walk around, so I got an angle
I bought Banjo again and installed it.
Usage impression is without complaint.
View detail
Things are good - - -
Although the quality as a thing was good, closing Banjo Nut was 11 mm and it was hard to use and it was KTC's Spanner
I can not join, is Black color a little thick?
View detail
Touch is not so good
I bought it because it is a bit cheaper than Swedge
I do not like the feeling of anxiety and Touch of Aluminum parts
It is necessary and sufficient for normal use, but you will not be choosing again next time.
View detail
BALIUS2 (Front) For Bolt-onBrake Hose Kit
BALIUS2 (Front) Bolt - on kit for Banjo Adapter, but the shape of Banjo Adapter was different from NORMAL. Although NORMAL has an angle of about 30 ° at both ends, this Kit interferes with others because it is One SideStraight. Since it can not be helped, I purchased Banjo as Single Item.
By the way for Rear was not a problem.
View detail
Cool and nice brake hose but the only thing is that the banjo bolt adapters are not included. Now i have to order the banjo bolt adapter separately.
Cool and nice brake hose but the only thing is that the banjo bolt adapters are not included. Now i have to order the banjo bolt adapter separately. View detail
It attaches with W650. The product made from an Aluminum should say that rigidity is weaker than iron in the Banjo adapter. Although the Design is the highest, if a Torque is applied by the Open wrench of Size 13, a crack is attached in a Revolv
It attaches with W650.
The product made from an Aluminum should say that rigidity is weaker than iron in the
Banjo adapter.
Although the
Design is the highest, if a Torque is applied by the Open wrench of Size 13, a crack is attached in a Revolver portion.
A special Design is spoilt.
since -- after protecting by a Tape or something, it may be good to apply a Torque.
Further, where a baffle is hit in a Banjo-adapter portion, the Torque was applied more than needed, and the Adapters has broken.
It cancels breaking with a root and being unable to use once.
It may be better to think that it is OK, if it attaches after performing Torque management firmly, but to purchase, when the product made from an Aluminum has been recognized firmly.
Incidentally an authentic positive one is iron, a price is high and there is a product made from a Stainless.
View detail
Although it is a vehicle type design, it is too short and is not generous at all! Three more cm is required. Pains is taken over attachment although attached. --
Although it is a vehicle type design, it is too short and is not generous at all! Three more cm is required.
Pains is taken over attachment although attached. --
View detail
Fits: YAMAHA XJR1200R, YAMAHA XJR1200, YAMAHA XJR1200
Since it was time-tested goods, I thought that it was called this and there was no difference, but there was no design of fitting well individually. Although I think whether to be a handy price, cheap one is also with how it is ... Efficiently, it
Since it was time-tested goods, I thought that it was called this and there was no difference, but there was no design of fitting well individually.
Although I think whether to be a handy price, cheap one is also with how it is ...
Efficiently, it can be used satisfactorily.
View detail