Reviews
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Fitting is very severe
Purchased to install on a 2019 YZF-R25 (RG43J).
The lever angle of this vehicle is too high for me, so I wanted to adjust and lower it, but the handlebar position is too far forward for a separate handle, and the Horizontal TypeMASTERCylinder immediately interferes with the handlebar, making it impossible to lower the handlebar at all. I bought it for the purpose of adjusting the position rather than the performance.
However, for the reason I mentioned earlier, the Straight shape banjo interferes with the lever when the brake hose is passed through it, so if the angle is increased to avoid this, the lever will now interfere with the cowl when the handlebar is turned to the Left.
In the end, I bought various shapes of banjo, made a tentative match, and finally managed to match them in-kind, "Here." The only way to get to a position and angle that is "right" is to use the "right" side of the needle. The process is like threading a needle. You can do this with "Conform" I wondered if it would be okay to say "yes" to this question. If you say that the product is compatible, please at least attach a fitting diagram for each major car model.
The installation may not be a problem for other types of cars, but for this type of car, the risk is too large for beginners to DIY, so it is better to leave it to the shop.
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125LIMITED, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125G, SUZUKI ADDRESSV125
It needed to be processed.
I bought this for a K5 Address for Replacement.
The diameter of the bolt for the brake lever is too small, so I had to use a drill to make the hole bigger.
In addition, when I blew out the air of the brake, the return side of the Master Cylinder was not equipped with a process to prevent the brake fluid from blowing out, so the brake fluid scattered a little.
The feeling of use after installation is that Brake is working normally without any particular problem.
View detail
Early life...
[How is it used?
Since OEM Parts are not available, this sale is very much appreciated.
However, 3 years after I replaced it, the push rod side started to leak a bit.
Of course, MASTERBody is free from scratch corrosion.
How was your experience with it?
It's equivalent to OEM Parts, so I think you'll get basic performance for a while after replacing it.
but the track record is that it started leaking after a little over three years.
KawasakiOEM Parts in this area have not been replaced for over 30 years. ・・・・
How did it compare to other products?
I don't have any other products to compare it to... so I can't write about it.
OEM Parts has lasted over 30 years.
[Points to note]
Of course, please make sure that there is no BALI or corrosion inside the Master Cylinder and that the surface is smooth before installing it.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
I guess I'll have to buy it again since it's the only one I have.
View detail
Fits: SUZUKI Address V100, SUZUKI SEPIA, SUZUKI SEPIA, SUZUKI ZZ, SUZUKI LETS II (2Cycle), SUZUKI VECSTAR125, SUZUKI VECSTAR150
More accurate product information!
I bought it because it was billed as being compatible with all ADDRESS V100s, but it was basically & let's consider rdquo; you can't pontificate”
Actual Handlebar diameter 19.5mm ProductHandlebar installation part inner diameter about 18mm So, if you tighten the bracket with the bolts, the bracket will be damaged
As a countermeasure, use the OEM Bracket that comes with the actual car and the Washer (which is also (Processing required)
The inner diameter was made closer to 19.5mm by installing a bite of the bite
Also, I tried to install the OEM Brake lever, but the thickness of the lever did not fit It does not enter the MASTER side
I think that there is an individual difference, but it shaves 1-2mm off the Brake lever and MASTER side with File We were able to assemble it by
I felt that the piston part of the Master Cylinder was pushed a little, but it did not drag Lever feels a little distant, but there is no problem in operation
The distance between the Mirror mounting thread and the Master Cap is less than the OEM Product I installed the Mirror through the Adapter because of the proximity to the Adapter I couldn't re-install the Mirror without removing some of the parts with a sander
As for my impressions, if you are not good at processing”MASTER& with Brake lever it is safer to buy the rdquo;
When the Brakes air is blown out, as others have written, the Brake liquid comes out with a good force So take your time to release the air
View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
The company's Semi-radial (Diagonal Horizontal Type) Exchange from
Although I had no complaints with the semi radius so far, I've replaced it with Hose exchange as I was already getting tired of getting full of the Clutch side already.
But I was not comfortable enough to acclaim like other people.
It certainly became easier to control, but Stroke got longer and more than anything, I did not smile at that smart Touch. I think that it is OK with NORMAL in this case.
Is it different for company b? Is price suitable?
Dress up parts and use it separately.
View detail
For attaching RAJIPON of a brembo to naked vehicles, mirror holders are indispensable items ... although he wanted to use an antlion, the mounting hole of a reservoir tank differs in level aplomb, and does not suit -- since like -- works -- although M
For attaching RAJIPON of a brembo to naked vehicles, mirror holders are indispensable items ...
although he wanted to use an antlion, the mounting hole of a reservoir tank differs in level aplomb, and does not suit -- since like -- works -- although Mr. Quality's thing was used, since the components containing the brembo logo of the handle attachment part of RAJIPON must be transposed to this, I am sad.
It is that the thing in which the logo of the brembo is contained with much trouble must be removed ....
And this color ...
Brown .. Why!? I want you to make not the color of stay but the color of a mirror holder main part choose. However, functionally with no problem.
If it dares to complain in a function surface, it will change that the installed height of a mirror is pure.
I wanted consideration at the point.
Or [ it makes lowness and can be made to carry out color (spacer) adjustment ].
Therefore, two stars.
View detail