Reviews
Fits: YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA YZF-R25
It looks better now.
Model YZF-R25
The Rear is quite dirty and it is now clean. the Brake Caliper is OEM and the Pad is DAYTONA, but I am glad I replaced it. The braking power is normally increased and I am satisfied.
View detail
It is a reliable Brand.
brembo is a trusted brand when it comes to brake parts.
This time I bought it as a Brake Disc for SpareWheel to use in Race.
[Super Sport] Floating Disc is already in use, so there is no mistaking its performance.
Compatible ZX-10R models are DISC DIA. Since it is Φ330, it takes a little time for the Brake to work properly at low temperatures.
It needs to be warmed up with a firm Brake in a sighting wrap.
The higher the temperature, the more stable the Breaking can be.
View detail
Fits: BMW S1000RR, BMW S1000RR HP4, BMW S1000R
Cospar good
After 10,000 km, the Large Rotor was stepped, so it was replaced.
The price is lower than the OEM Rotor and it is the same brembo as the OEM, so I didn't hesitate to buy it.
Installation is very easy
Accuracy seems fine. Thickness is the same as NORMAL.
I guess the wear of the rear brake rotor after 10,000 km is the price to pay for the front and rear interlocking brakes.
View detail
Fits: KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750RS, KAWASAKI 650RS
To Refresh Disc Rotor
I purchased this for use with my Kawasaki Z1.
I purchased this disc with HoleType because the OEMDisc Rotor was approaching its wear limit and I wanted a custom look.
When we removed the STD Disc for replacement, we found the difference in weight between the STD Disc and the Hadrill.
Along with braking power, we expect the weight difference will also change the driving experience.
Rotor replacement is not a difficult task if done carefully.
The bolt hole where the rotor bolt was removed was lightly cleaned with M8 fine tap, Locktite Blue was applied to the bolt, and the bolt was fastened at 26 N.m.
Pad should also be replaced with a new one.
View detail
Fits: HONDA CRF150F, HONDA CRF230F, HONDA CRM250AR, HONDA CRM250AR, HONDA CRM250R, HONDA CRM250R, HONDA XLR125R, HONDA XR250, HONDA XR250 Baja, HONDA CR500R, HONDA XR400R, HONDA XR230, HONDA SL230, HONDA XLR250, HONDA XLR250, HONDA CR250, HONDA XR600, HONDA XR650, HONDA XR250, HONDA XR250MOTARD
Yearly update?
I replaced the Front Disc on my 89 MD24.CRM250RK with a new one due to a Brake Overhaul. The original Rotor is still usable, but I replaced it hoping for a slight improvement in touch. The replacement was easy, but the OEM front hub cover could not be installed, so I applied anti-loose agent according to the service manual and tightened at 1kg/cm (98N/m). In the test run, I did not feel any difference in the touch and the braking power, partly because I had not yet gotten accustomed to the pad.
However, the lack of wear would be expected to improve Touch.
View detail
Fits: KAWASAKI Z900, KAWASAKI Z900, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS
Diversion to ZX25R
The SUNSTAR set for ZX25R is the same diameter and thickness, but not enough, so it was diverted.
Not compatible, but can be installed only by using Spacer collar (5mm).
The 310Φ4.5mm→320Φ5.0mm change increases the weight to 1300g→1430g.
I had hoped that the weight of the inner housing would be reduced to aluminum, but the weight has increased by about 130g.
If you want to use it all the way to the edge, you need to adjust it with Shimetc.
The texture is much better, but Fee Ring did not feel any difference on about public roads.
View detail
Fits: SUZUKI BANDIT600, SUZUKI GSF1200 S, SUZUKI GSF1200 S, SUZUKI GSF1200 S, SUZUKI BANDIT600, SUZUKI GS1200SS, SUZUKI GS1200SS, SUZUKI BANDIT600, SUZUKI BANDIT600, SUZUKI BANDIT600, SUZUKI BANDIT600, SUZUKI GS1200SS, SUZUKI GSF1200 S, SUZUKI BANDIT600 S, SUZUKI BANDIT600 S, SUZUKI BANDIT600 S, SUZUKI BANDIT600 S, SUZUKI BANDIT1200, SUZUKI BANDIT600 S, SUZUKI BANDIT1200
RearBrakes custom
Replaced in conjunction with the Front brake.
It's a shame that it's not very visible in the shadow of the CaliperBracket and Swing Arm, but I like it very much.
BrakeTouch is also easier to control than the OEM without being abrupt.
View detail
Not enough for use in Circuit
I replaced it with Gicu Ceramic sintered at the same time and used it on Circuit, and Judder appeared at full break in about 5 minutes after break in.
I don't know if it was incompatible with the Pad, but I was too scared to hold the Brake.
Then I switched to OEMPad and it was almost a non-issue.
However, since the thickness is 4mm, we decided to replace it with a 5.5mm one, considering the future endurance race and other factors.
View detail
Fits: SUZUKI sepia, SUZUKI Address V125S, SUZUKI Address V125S Limited, SUZUKI Address V125S Limited, SUZUKI Address V125S, SUZUKI Address V125SS, SUZUKI Address V125S, SUZUKI Address V125S, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100, SUZUKI Address V100
It's not just about looking cool!
[How is it used?
Commuter vehicle with a one-way trip of approx. 50kn
Was the one you received as per Image?
The package is a transparent plastic case without instruction manual.
It's not as oily as it should be, but it doesn't feel like it's been de-greased to dryness.
Was the installation difficult?
Brake is treated as an overhaul, so it's not for people who have never done any maintenance at all, but I just replaced it with OEM and had no fitting problems.
How was your experience with it?
I bought it for its appearance and price comparison with the OEM, but it works a little better and weighs a little less than the OEM. The weight is also a little lighter than the OEM, so I feel that the ride is more comfortable.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
It is not BALI, but the cutting surface is somewhat rough.
It is not so bad as to scrape the Brake Pads, but my Rubber gloves ripped a little, so be careful when handling them with bare hands.
View detail
Great!
I haven't run the car since I replaced it, but it has been good so far, so I assume this one will be good too!
If I had to say something, I would have liked a choice of thickness.
If we could make it 0.5mm or 1mm thicker.
View detail
Fits: YAMAHA MT-10, YAMAHA MT-10, YAMAHA MT-10, YAMAHA MT-10, YAMAHA MT-10 SP, YAMAHA MT-10 SP, YAMAHA MT-10 SP, YAMAHA MT-10 SP, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1
I had a hard time removing the OEM.
The product is good, I wanted the Rear brake to work a little better and it worked.
However, there were many places on the YAMAHA chassis where the Torque was higher than the Service Manual, and it was very strange to loosen the Torque here too. I tried to take the wheel to YSP, but I was able to loosen it by warming it up with a burner and buying a proper tool. The screw ruined 1 pc. I wish I had at least used a hex. It was not an easy part to replace at home.
View detail
Fits: KTM 690SMR R, HUSQVARNA SUPERMOTO701, KTM 690SMC R
Diversion to Husqvarna SVARTPILEN701 Spoke wheel
Since this is an OEM Equivalent Product, we give it 3 stars.
It can be attached to a spoke wheel, but cannot be used on a casting wheel.
View detail
Fits: HONDA CB400SF HYPER VTEC Revo, HONDA XL400 TRANSALPV, HONDA CB400SF HYPER VTEC Revo, HONDA CB400SFHYPERSpecII, HONDA CB400SF HYPER VTEC SpecIII, HONDA CB400SB, HONDA CB400SF HYPER VTEC, HONDA CB400FOUR, HONDA CB400SB, HONDA XL650V TRANSALP, HONDA XL600V TRANSALP, HONDA Africa Twin650, HONDA HORNET900, HONDA CB750
Rear brake rotor
When I had my CB750 RC42 inspected, the clerk at Honda Mahaja Super JOGZr Wing Black told me that I should replace the rear brake pad and rear brake rotor because they were worn out, so I bought the parts and replaced them myself. It took a long time to replace them, but it was a much easier replacement than I thought it would be.
It was a very enjoyable holiday. I think the next step is to replace the front brake rotors.
View detail
Fits: KTM 1290 SUPER DUKE SE, KTM 1290 SUPER DUKE GT, KTM 1290 SUPER DUKE R
Fully compatible with NORMAL
Fully compatible with KTM SUPER DUKE R 2016
Perhaps because the floating part is looser than in NORMAL, the dragging sensation characteristic of NORMAL did not appear.
The wheel is light, so the axle shaft can be inserted and removed with one hand. The Axle Shaft can be replaced in one hour.
I tried full breaking from about 100km/h. It works well enough, about the same level as NORMAL.
View detail
Fits: YAMAHA TZR250 SP, YAMAHA TZR250, YAMAHA TZR250, YAMAHA TZR250, YAMAHA TZR250, YAMAHA TZR250, YAMAHA TZR250R SP, YAMAHA TZR250R SP, YAMAHA TZR250R SP, YAMAHA TZR250R SP, YAMAHA TZR250R, YAMAHA TZR250R, YAMAHA TZR250R, YAMAHA TZR250RS, YAMAHA TZR250RS, YAMAHA TZR250RS, YAMAHA TZR250SPR, YAMAHA TZR250SPR, YAMAHA TZR250SPR, YAMAHA TZR250SPR
Exchange*.
I replaced the Front and I installed the Rear as well. View detail
Fits: KAWASAKI GTR 1400, KAWASAKI KLE Versys 1000, KAWASAKI KLE Versys LT 1000, KAWASAKI KLE Versys SE 1000, KAWASAKI KLZ Versys 1000, KAWASAKI KLZ Versys Se 1000, KAWASAKI Z 1000, KAWASAKI Z 800, KAWASAKI Z800, KAWASAKI Z1000, KAWASAKI Z800e, KAWASAKI Z R 1000, KAWASAKI Z800 Sugomi Edition, KAWASAKI ZX-10R , KAWASAKI ZX-10R, KAWASAKI ZX-14R , KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZZR 1400, KAWASAKI ZZR 1400
brembo is cool!
Replaced the front disk rotor on a Z1000 with over 50,000 km. Brake pads were also replaced.
Parenthesis is good from the cosmetic box.
As for the replacement, a new Bolt that stops the disc is provided.
Tools needed are Front stand and Hex socket.
The performance compared to OEM - I'm not sure, but I'm happy with the Brenbo lettering alone.
View detail
Fits: KAWASAKI ZX-14R, KAWASAKI ZX-14R, KAWASAKI Z750, KAWASAKI Z800, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI VERSYS1000 SE, KAWASAKI VERSYS1000, KAWASAKI Ninja1000, KAWASAKI Ninja1000, KAWASAKI ZRX1200 DAEG, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZX-14R High Grade, KAWASAKI ZX-14R
It will increase the appearance and control.
[How is it used?
I was not particularly dissatisfied with the rear brake area, but I bought it for the purpose of performance upgrade and dress-up.
Was the one you received as per Image?
The outer diameter and thickness are the same as OEM. I have the impression that the number of holes is larger than OEM.
The design is simple and plain, made of stainless steel on one side, and the brembo engraving is a good accent.
If you like the unique ruggedness of Racing parts, this is a good choice.
Was the installation difficult?
I don't know if it's a Kawasaki thing or not, but the bolt is really hard because of the screw lock agent. I don't know if it's a Kawasaki thing or not, but the bolt is very hard because of the screw lock agent. It takes a lot of nerve to turn it.
I recommend Spinner as a tool, be careful not to lick Bolt. if it does not turn with about 70% force, it is better to warm up around Bolt with Heat gunetc. and retry.
How was your experience with it?
Brake Pads were used and worn out, so to be honest, I don't feel that they have changed dramatically! I don't feel that the brake pads have changed drastically.
However, I feel that the initial braking when stepping on the rear brake is more gentle and controllable than OEM.
I have the impression that the braking force did not change just by replacing the disc. Personally, I was happy with the disc replacement because I was focusing on control.
View detail
The fact that you can only choose the color Red is fatal, isn't it?
For MC51 CBR250RR, the only color choice for inner rotor is Red. I was told by a staff member at SUNSTAR that there was a color custom order in the past, but they do not do it now.
My body was White and Blue, so a Reddish Rotor is out of the question. But SUNSTAR is the best design. What should I do? I decided to have it anodized by Koken, or paint it to match the wheel collars, the latter was my choice.
The new Rotor was disassembled and painted by having the plate Gold craftsman tone the color to match the color of the Wheel. The result was just like the Image, so I am Large satisfied.
View detail
Fits: SUZUKI GSX1000S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA
Front brake replacement
I don't know if it is a characteristic of the car model or not, but I don't think there is anything wrong with it. I don't know about the fine fee rings, etc. Anyway, Parenthesis is very good for self-satisfaction. View detail
Fits: KAWASAKI GSX250FX, KAWASAKI ZZR250, KAWASAKI ZXR250R, KAWASAKI ZXR250, KAWASAKI BALIUS, KAWASAKI BALIUS, KAWASAKI ZZR400, KAWASAKI ZXR400R, KAWASAKI ZXR400, KAWASAKI ZRX II, KAWASAKI ZRX, KAWASAKI ZEPHYR400χ, KAWASAKI ZEPHYR400, KAWASAKI W400, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI W650, KAWASAKI ZR-7 S, KAWASAKI ZR-7
Solid texture
The last time we replaced it, we replaced it with an unnamed manufacturer's product at a lower price. The quality was inferior to the OEM Product, and after about 5 years, the disc became distorted, and even though the disc thickness was still sufficient, it was replaced this time.
I was considering SUNSTAR for my next purchase, but I was not satisfied with the gold color of the rotor and could not make up my mind.
You can already tell the high accuracy by looking at it. Weight is a Quantity:The mounting bolt was also ordered from OEM Parts and replaced with a new one (the screw lock is pre-painted on the OEM bolt for mounting the motor). (The mounting bolt was also ordered from OEM Parts and replaced with a new one (the screw lock is pre-coated on the OEM bolt installed on the Rotor). (The screw lock is pre-coated on the OEMBolt for mounting the rotor). The front wheel was getting worn out at the point where I had to remove it to do anything related to the front wheel.
After the installation, it is clear that the stroke of the brake lever has become smaller, and the previous shaking of the rotor has become larger. I will not be able to experience it in actual touring, but I think it will only get better, so I expect it to be Large.
View detail