Reviews
No different than OEMs
Purchased due to leaking oil line. I am glad that the quality is the same as OEM and the price is lower. I will buy again when it breaks. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000 MkII, KAWASAKI Z1000 (air-cooled)
Maniacal Parts
I've been wondering about buying it for a long time … it's just a stick.
However, I think you can experience it.
For example, if you intentionally put a load on the Front and drive into the Corner, the Wheel turns smoothly, and the suspension moves well and feels light!
I just wondered if it is a Maniacal Parts, like … only for those who understand.
View detail
Rear axle shaft
I replaced the Front and it was so good that I also replaced the Rear.
The turnaround of the corner became smoother.
View detail
Fits: HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB
Front feels lighter!
I changed it along with the Front Disc replacement.
The weight is light, but the front tire feels lighter than expected!
The price is reasonable, so if you are not sure, try to replace it.
View detail
Fits: YAMAHA BW'S100, YAMAHA JOG, YAMAHA JOG-Z, YAMAHA GRAND AXIS 100, YAMAHA JOG50, YAMAHA JOG-EX, YAMAHA AXIS90, YAMAHA AXIS90 Profoot, YAMAHA AXIS Pro Foot, YAMAHA JOG90, YAMAHA Super JOGZ, YAMAHA AXIS90, YAMAHA AXIS90 Pro Foot, YAMAHA AXISPro Foot, YAMAHA JOG90, YAMAHA SUPER JOG
The weight of the description does not Ate.
OEM 3-type for horizontal JOG (480g) I bought it for the weight Up rather than the
The description gives a weight of 515g, but the actual measurement is only 496g.
OEMs usually increase or decrease by about 5g because of balance shaving, etc,
I could not think of writing an imprementation that I would recommend to others if the Cut-out Outer had an error of almost 20g!
[Regarding installation].
50cc horizontal JOG (3KJ/5AUCase before regulation, 5BM/5SUCase after regulation)
Case cover Gasket is required.
However, the shaft part is thicker than OEM, so when you stop the Nut, insert the O-ring, and try to close the Cover.
The gap with Bearing on the Cover will be insufficient.
So we need to take measures such as thinning the O-ring
・3WF
There's plenty of room to spare. o-ring should be as thin as the 50 story?
You can replace the Nut that stops the Outer with a thin Nut for 50cc
View detail
rebel 1100 dct
It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only.
It's a pity that the part needs to be processed.
It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only.
It's a pity that the part needs to be processed ------------------------------------------ ---------------- It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only. It's a pity that the part needs to be processed. It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only. It's a pity that the part needs to be processed. Powered by Google Translator
View detail
Fits: HONDA DAX125, HONDA MONKEY125
Room for improvement
This set comes with a connector to avoid cutting cables. Unfortunately my 2023 monkey did not have the connector in the pictures nor anything remotely resembling the connector layout. Had to cut cables, sadly. I managed to slightly round one of the handblebar bracket bolts from the set while tightening.. with a small ratchet. The bracket itself and the USB connector are nicely made. Back light is green. The cap seals nicely and gives confidence in water resistence. Manual is japanese. View detail
100 points
I think this is the most suitable exhaust system for DAX. The sound is a heavy bass! The sound is so powerful that it is hard to believe it is a Type 2 moped. Especially, the sound at the time of pinging downshift is unforgettable! It's so bad! (It is a little too loud at speeds over 6000 rpm, but it is just right for safe driving at legal speeds. I'm really glad I bought it. View detail
Fits: HONDA XL250S L250S, HONDA NY50 All models, HONDA CROSSCUB110 JA10, HONDA All models of GIORNO CREA AF54, HONDA SUPER CUB 110 JA10, HONDA SUPER CUB 110 PRO JA10, HONDA SUPER CUB series Engine cars (50-100cc), HONDA SUPER CUB series Engine car FI, HONDA Spacy50 All models, HONDA DREAM50 AC15, HONDA Spacy80 All models, HONDA VARIE All models, HONDA MONKEY series Engine cars (50-100cc), HONDA MONKEY series Engine car FI
Very common EXGaskett
CROSSCUB110 (JA45) Used to replace the Exhaust System of
I think Gasket is the same for all Manufacturers.
No exhaust leak etc.
It was cheaper than OEM Parts.
View detail
Touch may be too soft.
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Mounted on the underside with Bracket to improve serviceability.
The pad spring is very hard and the pad pin is press-fit, so we replaced it with an external pad spring and pin.
If you are a do-it-yourself maintenance person and use the new Crab, the above should be changed.
Even if you purchase the above, I think the price is low for an Aluminum Piston with high corrosion resistance and a pad.
The 30mm→34mmPiston changes the Ratio and the Pedal is very squishy.
10ROEMMASTER is 14Φ and there is nothing I can do about it because there is no MASTER that is any more LARGER, it should have been a 32mmPiston.
View detail
The glossiness is different from Fitting.
The company's Black fitting has a glossy texture, but this one is matte.
I would like to see it unified with Matte.
I tightened it with 20N, but it is stainless steel, so it is firm and secure.
View detail
Too bad about the color of Nut.
Purchased because the diameter of the Nipple no longer fit in the MASTER replacement.
Same shape as 10ROEM but OEM is 8mm diameter with domestic Spec. and this is 7mm diameter with RCS Nipple.
I thought they were the same except for the diameter, but the fixed nut on the lid is silver while the OEM's is black.
It's a fewmm of Nut, but it's a shame that it looks like it's floating when I wanted to create a unified look with Black.
I tried to replace it, but it is fitted like a ring of wisdom and cannot be removed.
View detail
Essential items for vehicles with external exhaust system replacement
After replacing the Tornado Exhaust System with Mukawa's Tornado Exhaust System, the Master Cylinder of the Rear brake stood out. I didn't like the whitish look of the Master Cylinder, so I covered it up with a Master cupCover. It looks good. View detail
Fits: SUZUKI GSX250FX, SUZUKI GSX250FX, SUZUKI GSX250FX, SUZUKI GSX250FX, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR250, KAWASAKI ZZR250, KAWASAKI ZZR250
Aftermarket parts are well stocked, so there is a sense of security.
I think it is semi-floating, so it should be reasonably durable, but even in case of emergency, it is helpful that all the parts can be purchased at Repair Parts. 。
I am currently using a Brembo caliper with no problems.
Comparison with bremboRotor purchased at the same time.
View detail
Fits: SUZUKI GSX250FX, SUZUKI GSX250FX, SUZUKI GSX250FX, SUZUKI GSX250FX, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400
I think Design is number 1.
I was worried about OEM, but the price was the same, so I went with SUNSTAR.
PremiumRACING is a great way to create your own combination!
There are various manufacturers, but I think Design is the best.
View detail
MASTER.
[How is it used?
Purchased a new OEM hose because it is not long enough to replace the Master Cylinder.
The OEMHose is a little short, so if you use an external master like brembo or GALE SPEED, it is not long enough, but if you use an extended VERSIONBolt, you can use it as is somehow, but the angle is a limit, so it could crack and break at any time.
Large front brake, so do not let your guard down!
Was the one you received as per Image?
Usual quality
At first I think it's made in Japan, but when I looked it up, it's a United Kingdom brand, so it's full of luxury!
Stickers are also included in the package, so you can quickly attach them to the car body!
Was the installation difficult?
Can be difficult if you're a beginner.
When removing the hose, be careful not to spill the Fluid!
If you put it somewhere, it will discolor or corrode quickly, so please prepare water before proceeding.
How was your experience with it?
as expected (as opposed to expected)
Soft and easy to angle
Nothing in particular that I think is wrong.
Just for reference.
Master Cylinder:GALE SPEEDVRC
Hose length:I bought 285mm, but when I installed it, 260mm is also enough, so I recommend 260mm.
In line with this, Active's Flare block adapter" should also be purchased in conjunction with the required
[Included Parts:were they on?
Sticker
[Was there anything that disappointed you?
I don't have it!
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
VERSIONBolt is not included.
View detail
Compact
Used 635mm on ZX10R (19) to install new Crab, just the right length.
The structure is simpler and more compact than the Edge line, which was previously used.
The Crimp section is shorter than the SuEdge for easy handling.
However, the Black part is shiny and not good, so I might have preferred the normal Stainless.
The texture of BlackStainless and the MachineMachine-like appearance of the Edge are better, but I have heard rumors that it leaks a lot.
If I had to choose by functionality, it would be Goodridge.
View detail
Relax with Stainless Steel
20° for new Crab installation.
Aluminum is the only choice for Stainless because it cracks.
It is surprisingly shiny, so I would like something with a matte texture from Hairlineetc.
View detail
Fits: HONDA CBR250RR, HONDA MONKEY125, HONDA CL500, HONDA CL250, HONDA GB350S, HONDA GB350, HONDA Super Cub C125, HONDA GROM, HONDA CB250R, HONDA MONKEY125, HONDA CB125R, HONDA CBR250R, HONDA CBR250RR, HONDA CBR250R, HONDA CB250F, HONDA CBR400R, HONDA CB250F, HONDA CB400F, HONDA CBR400R, HONDA 400X
Lever exchange is good.
I used to use the previous Active, but this one looks good with a rigid appearance and precision. View detail
Fits: TRIUMPH DAYTONA675, KAWASAKI NINJA400, SUZUKI , KAWASAKI ZX6R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z400, KAWASAKI Z250, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, KAWASAKI ninja, DUCATI Late 999, HONDA , DUCATI 749, BMW S1000R, BMW S1000RR
Wound-resistant DURACON
I used to use a Hook bolt also made by J-TRIP, but after repeated use, the bolt was too heavy.
The scratches on the surface of the wheel have made it look dirty, so we decided to replace it with DURACON, which has been used on Ninja 250R and has a good track record.
It is DURACON, so any scratches are not noticeable.
View detail