Reviews
very good product
In the original C125 condition, you can't really see the back.
You can change the mirror, but the original mirror itself is great, so I bought an extension kit.
In the end, I am very satisfied.
The rear view is much wider and you can see better.
The product itself was sturdy and the packaging was good ---------------------------------------- ------------------ In the original C125 condition, you can't really see the back. You can change the mirror, but the original mirror itself is great, so I bought an extension kit. In the end, I am very satisfied. The rear view is much wider and you can see better. The product itself was sturdy and the packaging was good. Powered by Google Translator
View detail
Even 30mm was enough.
Normal mirror was installed because it was difficult to see the reflection of the arms.
I don't have the 45mm in stock, I thought I could order the 30.
Checking the projection, I could see well behind me, which was an improvement even with Offset 30mm.
View detail
easy to read
I installed the mirror on my MONKEY125 because it was hard to see. The rearward view is not only easier but also extended to the front, so I can use it very comfortably with less eye movement. View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
TANAX OFFSET HOLDER 45
Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the side mirror visibility. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. -------------------------------------------------- -------- Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the view of the side mirror. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. Powered by Google Translator View detail
Buy 2, guys
You're purchasing a set of ONE unit. I made a mistake buying only one thinking it comes as a set of 2 units. Don't make the same mistake as I did. As for the product itself, no complaints - it's sturdy and good-looking. View detail
Best product!
I ride a current Z400.
Before installing this product, I could not even tell if there was a vehicle behind me, but after installation, I can see it differently and I am satisfied with Large.
If the price were a little lower, it would be a perfect score.
View detail
relief from a worry
I bought this for my CT125 because the LeftMirror is in a strange place and it was hard to see the back of the car.
I am happy with this Parts and it is much easier to see.
I was torn between 30mm and 45mm, but the 45mm is just right.
View detail
It was a little short!
After installing Extension India on PCX, Mirror and Extension India interfered with each other, so I bought this as a countermeasure. I had no choice but to adjust it by shifting the Extension India, but the interference could not be improved, so I decided to ride it as it is. I will buy OffsetHolder45 later. View detail
TANAX OFFSET HOLDER 45
125 years old, 125 years old, 125 years old.
I want to know more about this.
I bought the genuine Monkey 125 side mirror because I couldn't see the rear clearly.
After installing the offset holder, the mirror viewing angle will be good, allowing you to see what's behind you and drive safely. -------------------------------------------------- -------- The side mirror of the genuine Monkey 125 was purchased because it could not show the rear. After installing the offset holder, the mirror viewing angle is good, so you can show the rear so you can drive safely Powered by Google Translator
View detail
Back MirrorImproved rearward visibility
The rearward visibility of the Grom OEM Mirror was poor (about 1/3 of the arm was reflected) and I had to retract my arm every time I checked the rearward view.
When we tried to install it as it was, it interfered with the Throttle Wire, so we had to loosen the nut that secures the Wire and adjust the angle.
The installation has improved the reflection of the arms considerably, though not completely.
View detail
I need to buy two
Quality and texture information The paint finish is clean and good It certainly looks good on the sense of use Product to Buy Together Product # BCM-10 Installation difficulty easy Perfect for cost performance and comparison monkey 125 WeBike packaging is always great, arriving in a week for delivery and packaging Advice Since the screw is in the forward direction, it should be installed after checking carefully If you install it incorrectly, the screw line may be disrupted and the package configuration is composed of one, so please buy two and save time and money Many people buy only one View detail
It is a product that fits very naturally.
Since it hasn't been installed yet, I'll replace it with a photo of a club member. It matches as if it was originally installed by the manufacturer. Both build quality and materials are excellent. I first heard from a club member who installed it that rust does not form even without the bolt cap. It is heavy and feels solid. Very satisfied.
-------------------------------------------------- -------- It is still installed, so it is replaced by a member of the club members. It suits the manufacturer as if it was originally mounted. Both builds and materials are great. First of all, I listened to the members of the club. The weight is too heavy, so I feel hard. Very satisfactory. Powered by Google Translator
View detail
Off-set Holder 45 was better.
[How is it used?
Used to improve visibility of VTR250OEMMirror.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Angle adjustment is troublesome, but not difficult.
How was your experience with it?
Off-set Holder 45 was also purchased and compared.
It works well at 30, but 45 was better.
[Was there anything that disappointed you?
None in particular
[Opinions and requests to Manufacturer
It looks a little wild.
I would like a Mirror that can be placed forward without this.
View detail
Fairly easy to see.
[How is it used?
Used to improve visibility of VTR250OEMMirror.
Was the one you received as per Image?
As per Image
Was the installation difficult?
The angle adjustment was troublesome, but not difficult.
How was your experience with it?
Moving the Mirror forward has improved visibility considerably!
[Was there anything that disappointed you?
None in particular
[Opinions and requests to Manufacturer
It looks wild.
I would like to see a Mirror that can be placed further forward than the OEM without this.
View detail
It is as expected
I'm not sure if the emphasis is on styling, but at NORMAL length, it was quite difficult to see the back because the arms were in the way, but I was able to improve the situation. I am satisfied. View detail
30?
XSR155 with DAYTONA Mirror.
The Right Side looks good without this product, but the Left Side shows the body about half of Mirror.
With this product attached, it has become very easy to see and anxiety free.
View detail
Used in XSR155
I found this product when I wanted to do something about the fact that my body was quite visible in the Mirror on the Left Side.
As a result of the installation, the problem was completely solved. I am very happy with my purchase.
View detail
Good visibility even at 30mm
Installed on MONKEY125
I was worried about 45mm, but even with 30mm the visibility was sufficient.
I hope this keeps you safe.
View detail
cheap
[How is it used?
Mirror is now easier to see.
Was the one you received as per Image?
Yes
Was the installation difficult?
For beginners.
How was your experience with it?
Mirror is now as easy to see as I thought it would be.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail