Reviews
Large satisfaction, I should have changed it earlier.
I have tried various levers from brembo OEM, but this one fits me the best, including one for Clutch SideRCS.
When I inquired about the compatibility with my favorite XR0.11.71, I was told that it was not made by brembo, so I could not get an answer. I checked the description of ASite and found that RMCMASTER is available! I immediately bought it because the delivery date was earlier than this one.
View detail
ZETA X3 Protector
I installed the AdventureArmor Handguard and purchased the Protector from the same ZETA.
Although I was not sure if I wanted to go with the XC, which is a bit larger, I was happy with the X3 because it was a small motorcycle to which I would install it.
The Size is good for those who are OK as long as they do not get hit on the fingers by flying rocks or hard insects while driving, because it is Small for wind protection.
The Master cylinder guard, removable with Screw, was also a simple but interesting GuiMick.
Four bolts are also included, making it easy to install on vehicles that already have a hand guard installed.
The color White can be Blue-ish or Green-ish. I saw a Review that said
The color of the one I received was what can only be described as White when viewed indoors or in the sun.
Perhaps there is a slight difference depending on the production lot.
View detail
Fits: DUCATI 1098, DUCATI 1198, DUCATI 1199 PANIGALE, DUCATI 1199 PANIGALE R, DUCATI 1199 PANIGALE S, DUCATI 1199 PANIGALE TRICOLORE, DUCATI 1299 PANIGALE, DUCATI 1299 PANIGALE S, DUCATI 749, DUCATI 749EVO, DUCATI 749EVO CORSE SE, DUCATI 749R, DUCATI 749S, DUCATI 848, DUCATI 848EVO, DUCATI 848EVO CORSE SE, DUCATI 848R, DUCATI 848S, DUCATI 899 PANIGALE, DUCATI 959 PANIGALE CORSE
Adjustment range
It is great because the adjustment range is very fine. The other day, when I fell down on Circuit, the force was applied to the front side, and the Crack appeared at the root, not the lever. It is good for standing fall, but it may be weak for Circuit fall. I repurchased it again because of its good cost performance. View detail
Fits: HONDA CRF250L, HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250RALLY(S), HONDA CRF300L, HONDA CRF300L RALLY
Now in an easy-to-grip position.
The OEM clutch lever was too far away, and I had to grip it with the base of my thumb for support, which caused me pain, so I replaced it.
I wanted a firm four-finger grip, so I bought the 4FingerType.
I have seen other reviews stating that it was not as close as expected, etc., but in my opinion, it has improved a lot and is easier to grip.
I felt that 3FingerType would have been better because it pinches Small finger when I do it with 4FingerType Lever. (Lol)
It looks Parenthesis good and the grip is very comfortable.
Since the price is high, I'll put up with OEM for the Brake Side, which I'm not particularly happy with. (^_^;)
View detail
Fits: KAWASAKI BALIUS, KAWASAKI BALIUS II, KAWASAKI ER-6F, KAWASAKI ER-6N, KAWASAKI GPZ900R, KAWASAKI VERSYS1000, KAWASAKI VERSYS650, KAWASAKI Z1000, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI ZEPHER, KAWASAKI ZEPHER1100, KAWASAKI ZEPHER750, KAWASAKI ZR-7S, KAWASAKI ZRX1100, KAWASAKI ZX-11, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZZR1200, SUZUKI BANDIT1200
The pictures are confusing.
I bought this for use on a 2023 SV650.
It's my fault for not checking carefully, but I saw two Levers in the sample product photo, so I decided to order a Quantity:Pair (for Left and Right) Quantity:I bought it thinking it was Pair.
When it arrives, it is only Brake lever.
I had no choice but to purchase an additional Clutch, but since it was not sold for the SV 650, I had no choice but to return it.
The product itself had a good texture, but the sample photos were confusing.
View detail
please note
OEM Grip Heater Installation is not easy, the included bolt does not reach the handlebar weight, and even if the handlebar weight is removed, it cannot be installed with the Included Parts:. View detail
Neat around the Stem. I'm glad I bought it.
The Flasher is built into the x2Protector, and by removing the OEMBlinker, the Stem area is refreshed, making maintenance around the Stem area easier. View detail
zeta bar rise kit
I love the fast delivery. I also praise the meticulous packaging. It's before installation, but I feel that the product is in very good condition. It's not comparable to the one made in Chi** View detail
Fits: HUSQVARNA TE511, HUSQVARNA FE501, HUSQVARNA TC250, HUSQVARNA FE350, HUSQVARNA FC250, HUSQVARNA TC125, HUSQVARNA FE250, HUSQVARNA FS450, HUSQVARNA FC450, HUSQVARNA WR125, HUSQVARNA TE125, HUSQVARNA TE250, HUSQVARNA FE250, BETA X-Trainer 250, BETA RR2T 250, HUSQVARNA FE501, HUSQVARNA FE350, KTM BREMBO 125-530 XC-W 06-17, HUSQVARNA TE300, KTM 450 Rally
Nice upgrade
They will fit. They fit in the factory perches as good as the factory levers, and do fit behind the factory handguards with plenty of clearance. They are a well made product. Best levers I've ever owned. Crashed multiple times in hard pack, and soft conditions. They haven't even deformed. Will purchase for every dirtbike I own moving forward. View detail
Change from M6Type
I had fixed SONICHand guard on my M6Type, but the bar end weight of Kawasaki car is only fixed to the inside of the bar by rubber, so it was stress that the hand guard gapped due to vibration when riding. I took the opportunity of replacing the OEM handlebar and purchased this one and installed the hand guard. I am satisfied that the hand guard is firmly fixed and does not shake when mounted. Two types of attachments are included to match the inside diameter of the bar. In addition, the HandCard can be fixed in or out of two positions.
It is very solidly built, but therefore quite pricey.
View detail
Universality is strict
If the car model is not sold with a dedicated kit, the installation adjustment is Large strange.
I installed it on SUPER SHERPA, but cut and Screwed and bent,
We finally arrived and are not satisfied.
If you do not mind a gap at the Handlebar End, you can put it on without modification.
View detail
Changed from a fixed system to inner weight when handlebar was replaced.
The STD Handlebar uses a type that is fixed to the Inner Weight at both ends of the bar, but the Weight itself is only fixed by the Rubber, eliminating the Stress that causes the Guard to move due to vibration while riding. View detail
Fits: KAWASAKI ZX-10R, HONDA HAWK11, KAWASAKI Z1000, KAWASAKI Z1000R EDITION, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI NINJA1000, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR SP, HONDA CBR1000RR SP2, HONDA CBR1000RR-R, HONDA CBR1000RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR CONCOURS 14
2BL-PC40 Brake lever replacement
Brake lever replaced.
ZETA Pilot Lever Brake Item No. F5575
Fingertip feeRing is better than OEM Product.
I recommend it!
View detail
Fits: KAWASAKI ZX-10R, HONDA HAWK11, KAWASAKI Z1000, KAWASAKI Z1000R EDITION, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI NINJA1000, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR SP, HONDA CBR1000RR SP2, HONDA CBR1000RR-R, HONDA CBR1000RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR CONCOURS 14
2BL-PC40 Brake lever replacement
Brake lever replaced.
ZETA Pilot Lever Brake Item No. F5575
Shorter than OEM Product and better fingertip fee-ring.
I recommend it!
View detail
Fits 23-year 400X
I've been trying to find out and inquire if it will fit a 23 nc56 400X.
I could not confirm it, but I was able to install it.
It seems that the brake master is different from the previous generation SingleDisc brake models.
Installation was easy.
View detail
Fits: YAMAHA DT230LANZA, YAMAHA TW200, YAMAHA TW225, YAMAHA TRICKER, YAMAHA XT250X, YAMAHA XT250, YAMAHA TTR250, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA WR250X, YAMAHA WR250R
Turning blue
The short lever of the RALLY50 I have been using since the XG250 TRICKER rattled, so I decided to go out on a limb and replace it with this one.
You can see it shining Blue when you get on it, but you can't see it from the front because of the hand guard.
I don't think there is any difference in operability between the Short lever and the Large lever I was using before, but the range of adjustment is increased.
The OEM rubber cover cannot be installed as is and requires modification.
I kind of cut along the Bellows and it looks like the picture.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Tightens up the look.
Was the one you received as per Image?
It was something I saw often, so it's on Image.
Was the installation difficult?
I used a hand guard from the same Manufacturer, so no problem at all!
How was your experience with it?
I don't know if it is useful yet because I haven't driven it in a place where it would be useful, but it looks very atmospheric and satisfies my sense of ownership.
[Included Parts:were they on?
Installation Bolt
[Was there anything that disappointed you?
None
Other items that would be helpful
Of course, the same Manufacturer's hand guard is only a few minutes' work!
View detail
Might be useful to have.
I think it depends on the way you fall, but in my case, when I fell standing up on a forest road, this helped me to minimize the Damage. View detail
Easy to install, cost-effective, good-looking
This XCProtector is installed on a CRF150L with ZETAArmor HandguardBent.
The time required is about 2 to 3 minutes since it only stops two Screws on each One Side.
It looks LARGE and better as shown in the photo.
Cost-effective and great.
View detail