Reviews
Large satisfaction, I should have changed it earlier.
I have tried various levers from brembo OEM, but this one fits me the best, including one for Clutch SideRCS.
When I inquired about the compatibility with my favorite XR0.11.71, I was told that it was not made by brembo, so I could not get an answer. I checked the description of ASite and found that RMCMASTER is available! I immediately bought it because the delivery date was earlier than this one.
View detail
Fits: HONDA CRF1000L Africa Twin, HONDA CRF250 RALLY, HONDA CRF250L, HONDA CRF250M
You can open end with ease.
I bought it to attach a Closed type hand guard.
I was worried when I bought it because I read in other reviews that the total length was too short, but Large seemed to be sturdy.
When installed, the distance from the end of the handlebar to the end of the throttle tube is about 7mm inward. 120mm PROGRIP grips were installed, and they protrude a little from the throttle tube.
Although there is a gap from the edge of the handlebar, I thought it was a safe design with sufficient clearance considering that a hand guard is attached.
If Bar End is attached, gaps may be a concern.
View detail
Fits: DUCATI 1098, DUCATI 1198, DUCATI 1199 PANIGALE, DUCATI 1199 PANIGALE R, DUCATI 1199 PANIGALE S, DUCATI 1199 PANIGALE TRICOLORE, DUCATI 1299 PANIGALE, DUCATI 1299 PANIGALE S, DUCATI 749, DUCATI 749EVO, DUCATI 749EVO CORSE SE, DUCATI 749R, DUCATI 749S, DUCATI 848, DUCATI 848EVO, DUCATI 848EVO CORSE SE, DUCATI 848R, DUCATI 848S, DUCATI 899 PANIGALE, DUCATI 959 PANIGALE CORSE
Adjustment range
It is great because the adjustment range is very fine. The other day, when I fell down on Circuit, the force was applied to the front side, and the Crack appeared at the root, not the lever. It is good for standing fall, but it may be weak for Circuit fall. I repurchased it again because of its good cost performance. View detail
Fits: HONDA CRF250L, HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250RALLY, HONDA CRF250RALLY, HONDA CRF250RALLY(S), HONDA CRF300L, HONDA CRF300L RALLY
Now in an easy-to-grip position.
The OEM clutch lever was too far away, and I had to grip it with the base of my thumb for support, which caused me pain, so I replaced it.
I wanted a firm four-finger grip, so I bought the 4FingerType.
I have seen other reviews stating that it was not as close as expected, etc., but in my opinion, it has improved a lot and is easier to grip.
I felt that 3FingerType would have been better because it pinches Small finger when I do it with 4FingerType Lever. (Lol)
It looks Parenthesis good and the grip is very comfortable.
Since the price is high, I'll put up with OEM for the Brake Side, which I'm not particularly happy with. (^_^;)
View detail
zeta bar rise kit
I love the fast delivery. I also praise the meticulous packaging. It's before installation, but I feel that the product is in very good condition. It's not comparable to the one made in Chi** View detail
Change from M6Type
I had fixed SONICHand guard on my M6Type, but the bar end weight of Kawasaki car is only fixed to the inside of the bar by rubber, so it was stress that the hand guard gapped due to vibration when riding. I took the opportunity of replacing the OEM handlebar and purchased this one and installed the hand guard. I am satisfied that the hand guard is firmly fixed and does not shake when mounted. Two types of attachments are included to match the inside diameter of the bar. In addition, the HandCard can be fixed in or out of two positions.
It is very solidly built, but therefore quite pricey.
View detail
Changed from a fixed system to inner weight when handlebar was replaced.
The STD Handlebar uses a type that is fixed to the Inner Weight at both ends of the bar, but the Weight itself is only fixed by the Rubber, eliminating the Stress that causes the Guard to move due to vibration while riding. View detail
Fits: KAWASAKI ZX-10R, HONDA HAWK11, KAWASAKI Z1000, KAWASAKI Z1000R EDITION, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI NINJA1000, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR SP, HONDA CBR1000RR SP2, HONDA CBR1000RR-R, HONDA CBR1000RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR CONCOURS 14
2BL-PC40 Brake lever replacement
Brake lever replaced.
ZETA Pilot Lever Brake Item No. F5575
Fingertip feeRing is better than OEM Product.
I recommend it!
View detail
Fits: KAWASAKI ZX-10R, HONDA HAWK11, KAWASAKI Z1000, KAWASAKI Z1000R EDITION, KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI NINJA1000, HONDA CB1000R, HONDA CBR600RR, HONDA CBR1000RR, HONDA CBR1000RR SP, HONDA CBR1000RR SP2, HONDA CBR1000RR-R, HONDA CBR1000RR, KAWASAKI ZX-6R, KAWASAKI ZX-14R, KAWASAKI 1400GTR, KAWASAKI 1400GTR CONCOURS 14
2BL-PC40 Brake lever replacement
Brake lever replaced.
ZETA Pilot Lever Brake Item No. F5575
Shorter than OEM Product and better fingertip fee-ring.
I recommend it!
View detail
Fits: HONDA CRF250L, HONDA CRF250M, KAWASAKI D Tracker, KAWASAKI KLX250, SUZUKI DR-Z400S, SUZUKI DR-Z400SM, Others
Sporty TRAILHandlebar
Mounted on SEROW225. I used to use a Narrow Handlebar to attack the woods, but it was difficult to control and the form did not look good. The SEROW225 has less of the SEROW's "TRIAL" feel, but it is still great for situations such as Black Cannon and Motocross courses where you are standing still and driving at relatively high speeds. The texture is good, and the color is also very appealing, so I would like to repeat this every time I bend it in the future. View detail
Fits: YAMAHA DT230LANZA, YAMAHA TW200, YAMAHA TW225, YAMAHA TRICKER, YAMAHA XT250X, YAMAHA XT250, YAMAHA TTR250, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA WR250X, YAMAHA WR250R
Turning blue
The short lever of the RALLY50 I have been using since the XG250 TRICKER rattled, so I decided to go out on a limb and replace it with this one.
You can see it shining Blue when you get on it, but you can't see it from the front because of the hand guard.
I don't think there is any difference in operability between the Short lever and the Large lever I was using before, but the range of adjustment is increased.
The OEM rubber cover cannot be installed as is and requires modification.
I kind of cut along the Bellows and it looks like the picture.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Tightens up the look.
Was the one you received as per Image?
It was something I saw often, so it's on Image.
Was the installation difficult?
I used a hand guard from the same Manufacturer, so no problem at all!
How was your experience with it?
I don't know if it is useful yet because I haven't driven it in a place where it would be useful, but it looks very atmospheric and satisfies my sense of ownership.
[Included Parts:were they on?
Installation Bolt
[Was there anything that disappointed you?
None
Other items that would be helpful
Of course, the same Manufacturer's hand guard is only a few minutes' work!
View detail
the handlebar is highlighted
Repurchase due to size miss It's perfect for giving points to the zeta handlebar. I recommend buying it because it's cheap. View detail
Easy to install, cost-effective, good-looking
This XCProtector is installed on a CRF150L with ZETAArmor HandguardBent.
The time required is about 2 to 3 minutes since it only stops two Screws on each One Side.
It looks LARGE and better as shown in the photo.
Cost-effective and great.
View detail
Cool with increased protection
ZETAArmor HandguardBent on CRF150L.
The instruction manual is also very helpful and reliable. Basic installation is also easy.
If there was a hole on the SIDE of the handlebar rubber, we would have installed it as is, but since our car was blocked by the rubber, we drilled a hole with a cutter (the Instruction Manual also says to replace the grips).
The Left Side was easily installed, but on the Right SideThrottle side, the bottom of the Rubber was blocked by Plastic.
Carefully crush this with a Hammer, etc. and install. CRF150L users, please be careful.
Once the hole is made, installation is easy and from there it takes about 10 minutes, as shown in the photo.
It looks good and has a large increase in protection.
It is good enough as it is, but we will also add XCProtector after this.
View detail
Fits: KAWASAKI D-TRACKER, KAWASAKI KLX250, Others , YAMAHA WR250R, YAMAHA WR250X
There are some good things that only a comp bar can do.
I put a MOTARDMedium comp bar on my CRF250RLY50.
I had worn cx bar mx-123Blue before, but I thought it would be more comfortable with a little more aperture in terms of position. I decided that the comp bar would fit CRF250RLY50, which is not so strong and rigid, and bought it.
As a result Large was the right answer
The position, moderate rigidity of the handlebar, and coloring are perfect.
View detail
Stability only possible with Fat bar
This is a Review at least 6 months after purchase.
Quantity:Pair (for Left and Right) Fell multiple times on Tarmac in (SlipDown type) were, but there are no visible signs of breakage or bending, and the feel of the product remains the same.
The length of the bar is 800mm, which may be a little too large for some Japanese, perhaps due in part to the length adapted to the physique of Westerners. I use it with the bar packed.
Motocross athletes often use them without filling them these days, so if you take that into account, you can use them without any particular concerns.
View detail
Good to have a variety of colors to choose from.
This one is good because it offers a variety of Coloring choices.
Both Cx and sx bars come with Pad as standard, but the Black is Quantity related to the color of the bar.:Set
Inevitably, every time you buy a bar, Black's Bar pad will accumulate in droves! 。
There is almost no profit to be made selling them on Mercari or Yahoo!
I would like to be able to choose the color of the Pad anyway, but I think it would be better if the Pad is treated as an Option like the comp bar and the unit cost of the Handlebar is lowered.
View detail
It's crisp and clean.
This is a change from OEM.
The installation can be done without too much difficulty if you have experience in such work as replacing the clutch lever, since there is a translation (please enter hereManual).
Also, while installing it, I felt that the accuracy of the cutting process may vary a bit, and you may be dissatisfied with the Quick Adjuster for Red and Blue. The color will deteriorate under ultraviolet light while in use, and the color will fade, but if you are considering purchasing these as Custom, please be aware of this.
Grease is also applied to the bolt that fixes the lever from the beginning, and the handlebar is fixed with a clamp system, and the screw is very precise, so it was installed comfortably.
The clamp that fixes the handlebar is a little hard plastic material, so there is a possibility that the entire clamp may rotate when it falls over. If you are concerned about it, you may want to change to RubberMaterial.
As for the feel of the operation, as per the Title, it is snappy and sharp.
If you want a direct feel from it, I think you can further modify the Sleeve in the Thailandico fixation area.
Even with the Sleeve position in its normal state, the OEMLever comparison is better, so I felt that the Point is a point of preference depending on how a person uses Clutch.
I wish I had not been stingy and purchased it earlier, as it is one of the other Items that can be fine-tuned for Lever position.
View detail