Reviews
Simple and easy to use
It is really the smallest and simplest helmet lock. I am glad that it is inexpensive. I installed it on my Honda Giorno Grab Bar. Thank you very much! View detail
Standard Handlebar (22.2mm) Mounted on
Since MOTOCOMPO did not have a helmet holder, I added it to the appropriate place in the Handlebar.
Similar ones are sold on amazon for similar prices, but the Bracket is thinner and more flexible for installation.
However, the Fixing Screw on the bracket is exposed, so if you are concerned about it, you may want to replace it with a special screw. (I think the attached screw is just a Hex Screw.)
View detail
Easy Helmet holder
It is a good and inexpensive Holder, but the drawback is that you have to turn the key to close the Hook.
It would have been better if the Hook could be locked by pushing it in.
View detail
Helmet holder
Option parts for SUZUKIOEM.
Fixed Band, Bolt is Material:Stainless Steel eliminates corrosion concerns.
As an OEM Product, it seems to have been sold before Large.
It is less expensive and better than what is available in Option these days.
View detail
It's nice and casual.
I was looking for a helmet lock that was simple, small, lightweight, and unobtrusive, but I could not find one, and then I found a helmet lock that looked just right.
SimpleHelmet lock is a key type lock that is highly universal to fit on the Pipe Handlebar, just like the OEM lock of SEA BASS. (Key case is reappearing)
I purchased it immediately and installed it. It can be installed with only two HexBolts and seems to work fine as is for a short time. (Security measures are necessary when using it for long periods of time.)
The installation took a few minutes and a lot of time, worrying about the mounting position and angle, but it fit easily by the LeftMirror Holder.
It is a SEA BASSOEM Product that is light in operation, can be locked securely, and is easy to use without getting in the way. (It is SEA BASSOEM, but the texture etc. seems to be KawasakiOEM)
The Bolt and BodyReverse side of the unit is particularly prone to rust, so it is recommended to lightly cure the exterior with Chain Lube etc.
Nevertheless, I think that this workmanship with this content is the strongest cosmetically compared to other Helmet locks.
View detail
Gap-entry theft deterrent device
[How is it used?
One dayTouring installed on Handlebar of MiddleSports vehicle (YZF-R6 13S:2016).
Was the one you received as per Image?
I was surprised to see the SEA BASS logo mark on the body side, which I had not seen on the image.
The bracket that locks the helmet is also thick enough to provide a sense of security.
Was the installation difficult?
Installed by replacing the cf posh universal holder (apparently 10.4mm wide) with a BoltQuantity:It is easy if you look at the Body alone, as it can be installed with 2pcs.
How was your experience with it?
Unlike the U-shaped Helmet lock found in KIJIMA, the locking parts move with the movement of the key, so the key is needed not only when unlocking but also when locking.
Although there is some inconvenience because the key cannot be removed while unlocking, it is appreciated that it can be used for general handlebars regardless of the type of car.
The YK-030 HelmetFirmlyLock cable from Yamashiro is wide enough to fit through both rings, which is what we had hoped for.
[Included Parts:were they on?
It has a bolt that is necessary for installation, but it is a common bolt that can be turned with a hexagonal wrench, and there is no loosening mechanism. Because it is cheap.
[Was there anything that disappointed you?
Maybe it's to put Logo in the key, but I think the key Body is a bit wide. It is easy to grab, but it does not fit into the key case.
It can be installed in a small amount of handlebar space on MiddleSports vehicles. There is no model-specific helmet lock, but if you want to install it, this product would be the Pile of choice.
Even if it fails, it is a minor injury because it is even cheaper than the common KIJIMA and KITACO helmet locks.
View detail
Add to handlebar of MOTOCOMPO
It can be attached anywhere with the same Pipe as the Handlebar diameter, so it is convenient if you have a NAKED or Handlebar and want to lock it for now.
The installation is a normal Hex, so if you are concerned about it, you might want to change it.
It is good for motorcyclists who don't want to carry their helmets on their motorcycles, but don't have a helmet holder or don't want to take it with them when they are in convenience areas.
View detail
Good
Well made and works fine.
Easy to install, and at this price… I am satisfied.
View detail
Mounted on KSR80
I bought a KSR80 and enjoy riding it, but I felt inconvenienced by the lack of a helmet holder.
I was wondering if it would be stolen if I removed the Screw, but removing and attaching the Brake master prevents it, and I think it was attached in the best position for me.
The quality of the OEM Product is assured, but it would be even better if the key could be pulled out and locked without a key even when unlocked.
View detail
Good
I put it on CUB's Carrier.
So-so feel.
View detail
Inexpensive and easy to install
This product is inexpensive and easy to install. The Screws have rusted in the rain, so if you are concerned about this, recommendendation a rust inhibitor. View detail
A classic?
I can't complain about this price with this spec. and this function with ManufacturerOEM.
EPO (PV50) I think the OEM has it on the
If you're driving a Pipe Handlebar car, you're in for a non-SEA BASS car!
View detail
Cheap, but well made!
I found this Helmet holder by chance.
It's amazing how cheap they are for something so well made!
I'm thinking of buying another one.
View detail
Security-wise, I'm a little nervous.
The CHOINORI does not come with a standard helmet holder, so I bought this one for convenience.
The manual recommends using the HandlebarLeft Side next to the switches, but I didn't want to get in the way of the switches, so I mounted it in the middle of the Handlebar.Hexagon cap boltQuantity:There is a little uneasiness in the security aspect because it is only stopped by 2pc, but it will be far better than only hooking it to Mirror or Handlebar.
View detail
It's worth the price.
[How is it used?
The XJR1300C doesn't have a helmet holder, so I chose this product which is cheap and looks easy to install.
Was the one you received as per Image?
The product images were well posted and were as Image.
How was your experience with it?
The price is right. It does its job well, but the key body sticks out unexpectedly, and it's a bit of a pain.
It is difficult to use because the key does not come off when you turn it...
At least I hope I can pull the key out when I open the key.
[Points to note]
There are no special requirements, but it is not recommended to install the key hole pointing straight up.
There is a risk of rainwater entering the cylinder and causing the cylinder to stop turning.
How did it compare to other products?
The KIJIMA Universal is more troublesome to install because you have to make a bracket.
This is difficult to use, so I will switch to KIJIMA.
View detail
Helmet holder mounted on Handlebar
The OEM Helmet holder on my D-Tracker 125 is not stable and I feel like I might get hit or kicked by a neighboring bike parker, so I wanted to add a Holder to my Handlebar.
I considered the position to hook the Helmet to the edge of the Mirror or Handlebar, but the chinstrap was too delicate to reach, so I changed the direction to place it on top of the Tank.
The problem is still that you can't remove the key until you lock it, so it's not easy to operate.
I guess it's a matter of getting used to it, but maybe the position should be rethought a bit more.
However, since there is no lid on the keyhole, the flexibility of installation is also limited considering the rainwater intrusion, so I feel that the area is demerit.
View detail
Best in the cos. deal with M5×12mm tinkering Torx bolt
The RAN Bretta V125 doesn't have a helmet holder, so I mounted it on the Rear Carrier (φ16.5mm) with a thick Rubber. The bolt is visible from the outside, so I used M5×12mm Torx bolts. I like it, even if it is a bit cheap looking.
As you can see in the picture, if you put it on Up, Helmet will not fall down even if you open it, and it is quite easy to use.
And above all, I appreciate the low price. Highly recommended.
View detail
The definitive UniversalHelmet lock!
The Helmet is not a good place to leave your motorcycle when you are touring.
You can hang it on the Mirror, but you don't want to leave it there with the Risk, stolen or dropped!
Helmet holder is useful in such a case, but most of the models with small engine displacement volume such as Scooter and Mini bike do not have helmet holder.
To be honest, I've never seen an OEM helmet holder that is easy to use on a motorcycle with a mid-engine displacement volume or higher, because the OEM helmet holder has a weird mounting position or the keyhole is in a weird place. I've never seen an OEM helmet holder that was easy to use.
There are also Helmet holders for sale, but they come with overspecifications like a gorgeous bracket set, or on the contrary, they are so cheap...
I'm looking for a product that's as high quality as OEM, cheap, and can be installed anywhere. Is there such a selfish product ・・・・? Good news!
Do you have a problem? SUZUKI of the world will solve your problems.
This product is a ManufacturerOEMOption, but it can be installed anywhere on a 22.2Φ (same as the Handlebar length) Pipe, with Key, and it is plated and looks good, and it is cheap! This is the best Helmet lock, but not many people know about it.
We hope you will try it too.
[Was there anything that disappointed you?
The inability to hold the key in the open position.
You turn the key to open the lock, but if you press the claw part of it with your finger, it returns to the locked state.
If you push the wrong way when hooking the D-can, the nail will retract, which is frustrating (if you can tell...)
And of course, it is OEM parts of SUZUKI, so it is proudly displayed on the key. "SUZUKI" The logo of the company sits in the middle of the room.
If it is used for Motorcycle of SUZUKI, there is no problem, but when other Manufacturer diversion is done, it becomes a little uneven.
Do you have any wishes or improvements you would like to make for the Manufacturer?
The above actions (such as adding a little resistance when returning from full open)
[Do you have any products to compare it to?
Helmet lock
What made you decide to buy?
High price, with Key, and Universality
How was your experience with it?
The function is fulfilled. There is a little bit of regret, but it is acceptable because of the high cosmetic value.
Was the installation difficult?
Done in the blink of an eye (ScrewQuantity):(Just fasten with 2pc)
View detail
Bar handle can be used for most of the car models.
It is OEM Parts and the price is cheap and well made. However, it is a pity that the key cannot be removed in the unlocked state. View detail
I didn't know OEMs could be bought so cheaply!
I'm cheap, textured and Large satisfied!
But I do have one complaint...
It would be much easier to use if the key is removed when you open it with the key...
View detail