Reviews
Repair
I am embarrassed to say that this is a replacement due to a standing blockage.
When ordering products, you can choose which Shop you would like to have installed.
After that, the installation process is completed with only a few email exchanges. As for the product, it is well packaged and I have nothing to say.
View detail
Fits: YAMAHA MT-09, YAMAHA MT-09 To Racer, YAMAHA MT-09SP, YAMAHA MT-09
Looks well made.
It is a well-known name, Striker, so the product seems solid.
The Bolt part is black, so it's a little bit expensive;
Tightening Torque is like 45N.
It was so low level that I thought, "Is this what it's supposed to be like? It was a Level that I would say "this is what it is like.
In the meantime, I painted 243 of Locktite.
I hope it will not be used because it is a talisman in case of moss.
Also, I wish the price was a little lower.
View detail
Fits: Others , KAWASAKI NINJA250 R, KAWASAKI NINJA250, KAWASAKI NINJA250, KAWASAKI NINJA400, KAWASAKI Ninja ZX-25R, KAWASAKI NINJA250, KAWASAKI Ninja ZX-25R SE KRT, KAWASAKI NINJA400, KAWASAKI Ninja ZX-4R SE, KAWASAKI Ninja ZX-4RR, KAWASAKI Ninja ZX-25R SE, KAWASAKI NINJA250
Completely pull out the Axle Shaft from the car body and install it.
Replaced OEM rubber cover. The Axle Shaft needs to be completely removed from the car body and fixed to the car body again after installation. View detail
Fits: Others , KAWASAKI NINJA250 R, KAWASAKI NINJA250, KAWASAKI NINJA250, KAWASAKI NINJA400, KAWASAKI Ninja ZX-25R, KAWASAKI NINJA250, KAWASAKI Ninja ZX-25R SE KRT, KAWASAKI NINJA400, KAWASAKI Ninja ZX-4R SE, KAWASAKI Ninja ZX-4RR, KAWASAKI Ninja ZX-25R SE, KAWASAKI NINJA250
RearASKUL Department is Refreshing
It is necessary to remove the tire. The actual work is to fix the Rear tire with the Racing Stand, pull out the OEM Rear ASKUL once, install Striker's Parts, and put the Rear ASKUL back in the Quantity.:Set.
It was not necessary to completely isolate the Tire from the vehicle body.
In addition, it is necessary to pay attention not to tighten too strongly and not to loosen the tightening from day to day because the Slider itself is not the genus Gold.
View detail
Installed on CBR650R 2021 MODEL
I bought it to reduce scratches when I fall down.
Installation is easy because it is Bolt On.
I am satisfied with the quality of the product.
I don't want to feel the effects...
View detail
For ZEPHYR1100
I bought this because of a standing injury.
I have considered Slider from various Manufacturers.
I bought Striker's Engine slider because it has three slits and the word Striker on it is Parenthesis good.
I was troubled with Black Spec. but because my engine is Silver, I bought Standard Type which has Silver base.
The installation is still in progress, so I can't get a feel for it yet, but it's a manufacturer I trust, so I'm sure it'll be fine!
View detail
It's a little pricey.
The price may be a little high, but I tried to match it with the Swing Arm of G-striker.
Needless to say, the quality is good and of course it functions well.
View detail
Cool
I installed it on my 21 year old CBR650R. (Spec.:All black)
Installation is very easy, just remove and replace the existing Bolt.
I wanted to buy Babyface, but it takes time to deliver, so I chose here.
When I installed it, it is very nice and Parenthesis is good.
As for the one made by Babyface, there are several fixed Bolt, and I thought that this one was simple and good.
I don't know the actual effect yet, but I still feel safe.
View detail
Satisfied with the protection performance
For CBR650R
It was released at the same time as the Baby Face, so I was wondering which one I should choose, but I had to wait for the delivery date slightly Hand over here
Installation is very easy and does not require any modification to the Cowl Pulling out the Mounting Bolt, the body in place with the Bolt that comes with it there Just tighten it up with Torque It took me about 30 minutes to work on it, and it's easier to work if you just lift the rear wheels in STAND It is
The Slider tends to lose its large appearance, but the CBR650R's Cowl The area is small, the color blends in with the black of Engine, and the shape is so-so Stylish, so it didn't stand out as much as I feared it would
Protection performance is based on Cowl, Pedal, and Engine by standing moss while at rest There was no damage to Coveretc. and it was only a few scratches on Mirror and Bar End Its performance in tipping etc. when running is unknown, but it did the job properly
View detail
Fits: YAMAHA MT-09, YAMAHA MT-09 Tracer, YAMAHA MT-09SP, YAMAHA MT-09
The so-called Frame Slider
It's just a Frame Slider The feature is Quantity:Pair (for Left and Right) The Left Side is longer than the Left Side, and it seems to have taken into consideration the protrusion of the Crankcase
To install, just remove the Engine Mounting Bolt of NORMAL and install By the way, if you don't do it one by one, the Engine will fall off and the Bolt position will be Gap You'll be a W
The attached Bolt is a 14mm box wrench with no deep socket And I can't tighten the Bolt I used 4.5Kg to tighten the Torque because it says it's the same as the OEM I don't need the Torque as much as I thought I would
The DAYTONA Slider I used to wear is more than 5,000 yen cheaper than this, but I did a low SIDE in Circuit, and voila! It was split in half It was not shaved, but broken in half This time I tried to make it from Striker, which is more expensive Because it is not mossy yet, I do not know the true value
View detail
The texture is good
I installed it to GSX-1000F It was able to be pontooned on without any modification of the cowl, etc The texture is good, but the drawback is that the price is high! View detail
Good but expensive?
It's high in texture and rigidity, but it's also solidly priced!
But it's not a substitute, and it's not something that I don't agree with, but it's a good start anyway Maybe you could make it from Kit?
View detail
High quality but …
GStriker's Swing Arm in Swing Arm
I'm very happy with the way it looks As expected, the accuracy is perfect and there is a sense of quality and satisfaction But do I need to sell this Base kit separately? It shouldn't be that much wear and tear on the Plate even if you use it fairly often?
View detail
The texture of Black is good.
It is cool that the texture is also that the Gold genus part is Black.
The Gold genus part is smart, but I feel that the design of the Slider part is not good (depending on the individual. )
Somewhat higher than other companies (Especially Black) I think Minus is the one.
View detail
I chose by appearance and installation location.
Easy to install, just remove the Bolt of the car body and attach it with the included Bolt.
I thought that there was the most bumpy feeling compared to other Manufacturer so I bought it.
The rest is where I liked this place to install.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZX-14R, KAWASAKI ZX-14R
Worried whether the installation is correct.
I intended to install it as Instruction Manual but I do not feel like it is somewhat different from the illustration of Instruction Manual. I thought that the Instruction Manual was nice and polite. View detail