Reviews
Body installation itself is easy
Since I bought a used NINJA1000 without a slider, I installed a slider to reduce wounds when falling down.
Removing the cowl is a bit of a hassle, but once removed, it was very easy to install the base plate and the slider cone. However, the M8 Cap Bolt that holds the slider cone in place may loosen easily, so the use of a screw locker is recommended.
It was inexpensive compared to otherManufacturers and the installation diagram in the Instruction Manual was easy to understand.
Two Logo stickers were included.
View detail
It protected me from standing moss.
I had the same thing installed when I purchased the vehicle. It was not the original purpose of the Slider, but it helped. I only replaced one of the sliders. When I was replacing it, I was playing with the one I had installed and the Black Anodized was peeling off. .... How is it in terms of quality? I feel like I have to ask myself, "How is the quality of the product?" But there are not many other options for this type of car. I just hope I won't have a chance to replace it next time. I am very happy with the quality of the product and the points it comes with. View detail
Custom
Items we do not want to be indebted to you.
The appearance of custom feeling will be increased.
View detail
I think it is cosmetically good.
I think it is a good product in terms of cosmetics, but I would like to see some improvement in design. View detail
Fits: KAWASAKI ZRX1200, KAWASAKI ZRX1200 Daeg, KAWASAKI ZRX1100
I think it's good
I haven't put it on yet, but it seems sturdy. View detail
Fits: TRIUMPH Speed triple, TRIUMPH DAYTONA955i, HONDA VFR1200F, HONDA CBR1100XX, HONDA CB900Hornet, HONDA CB600F, HONDA CB500X, HONDA CB500F, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR650F, HONDA CBR650R, HONDA CB650F, HONDA CB650R
Standstill Backup
When parking the car, it fell over and broke Babyface's Slider,
The Crank Case Cover, Under Cowl and Exhaust System were scratched.
I did not expect Slider to break,
I put on the Timing Hole Plug for a double measure.
It is quite expensive, and if this gets damaged, that would be sad,
I feel it would be cheaper to replace the Crank Case Cover.
However, I think the pointing color of Orange works well and tightens up the Cover area.
View detail
Fallen cannibals
The pedestal is rugged, but it is attached at a position where the Damage does not go directly to the body of the vehicle at the tipping angle.
Quantity:Pair (for Left and Right) Asymmetrically, there may be a preference for or against, but it seems to serve the role well enough.
View detail
We will protect it well.
Well done.
If the Swingarm Protector is used in combination with the Mirror, Handlebar Weight, and Lever are only affected by a fall.
It protects them well.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS Cafe, KAWASAKI Z900RS, KAWASAKI Z900RS Cafe
Frame Slider
The price is low, installation is easy, and Parenthesis is good. View detail
Fitted on a 2023 Honda CBR250RR
It is also available for the 2023 model year.
I am very satisfied with the beautiful finish of the Large size change in Aluminum Cut-out.
Aluminum Collar for installation is attached, but there are two sizes, 10mm and 12mm diameter. 12mm diameter can hide the scratches on the crankcase bolt hole when the OEMBolt is removed, but 10mm diameter can show the scratches a little. However, the 10mm diameter Bolt is slightly scratched.
I would have liked them all to be 12mm diameter colors if possible.
In my case, I inserted a commercially available 12mm Washer so that the scratches would not be visible.
View detail
I even bought Hexagonal.
Installation is easy, but in the case of RR-R
Tighten the Frame Slider mounting bolt to 64Nm.
If not, it will affect the running of the car. Therefore, we purchased a Long Hexagon socket separately and tightened it with a torque wrench.
View detail
BabyfaceFrame Slider
This was purchased because it would not catch and slide if it did.
Well, I haven't experienced the effect and don't want to, so the effect section of the evaluation is a rating to look at.
I knew the Gold amount was too high and SliderBracket (bar) The SliderBody is attached to the body and a screw is cut on it, so the SliderBody is turned around and attached to the body, and then the screw is used to stop the body from turning around. But when I tightened the screw at any position without tightening the SliderBody to the end, it was loose.
View detail
Babyface Frame Slider
The standard Frame Slider is installed.
It is not as uncomfortable as I expected.
BMW is ridiculously overpriced for Cowl, so it's safer to put it on.
View detail
Babyface Engine slider
I bought the BodyStyle Under Cowl because the KawasakiOEMSlider that I had been wearing for some time would not stick to it after I installed it.
I had installed the same manufacturer's Slider on my previous S1000RR. Fortunately, I have not had to use the Slider yet, but I think the shape is good and not too assertive.
View detail
if you don't mind protruding
It is much cheaper than foreign products, and I am grateful that they make these vehicles even though they are not available in large numbers.
You will need Torque, so you may have to spend extra on that, but while you're at it, why not use the Quantity:I prepared it with Set, myself.
The length of Bolt is a little bit complicated, so it is better to check it with Scale.
View detail
Fits: YAMAHA MT-09, YAMAHA XSR900, YAMAHA XSR900
BABYFACE Babyface Frame Slider (Direct type)
[How is it used?
City Riding, Touring Main
Circuit not running
Was the one you received as per Image?
No different than the Image in the photo.
I love it because it is easily recognizable as a Babyface product.
Was the installation difficult?
The installation itself is easy.
However, the bolt and color specified in the Instruction Manual must be used in the specified location.
Quantity:Pair (for Left and Right) The body and bolt lengths are different between the two, so installation must be carried out in accordance with the Instruction Manual.
Since a part of the engine hanger bolt is to be removed, be sure to complete the installation of the One Side before moving on to the opposite side.
Worst case, the Engine position drops from the Frame and the Engine has to be lifted.
The Bolt itself is quite hard to remove, so be careful not to overreach and injure yourself.
Since this is an engine hanger bolt, it is recommended that the bolt be tightened to the specified torque after installation.
There is a groove carved on the outer circumference of the Protector, but the groove is not chamfered in that area.
Cutting hands. Either chamfer or don't touch with bare hands.
How was your experience with it?
It looks good and is available as custom parts.
Drive safely so that this will not come in handy.
Since the amount of protrusion is reasonable, there is a feeling that it will be protected.
There is no sense of hindrance by objects when pushing Motorcycle by hand.
The design is also good, with the glimpse of orange anodized accents.
[Included Parts:were they on?
It consists of several Parts.
But it is known, so there is no need to be troubled.
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Quite inexpensive compared to Y's Gear's Protector, but a little less expensive would be appreciated.
View detail
Fits: HONDA CBR650F, HONDA CBR650R, HONDA CB650R, HONDA CB650F
BABYFACE Babyface Frame Slider
[How is it used?
It has been in use since August 2020.
Was the one you received as per Image?
Photo
Was the installation difficult?
Anyone who can read the instruction manual can do it.
How was your experience with it?
I have not yet taken care of Frame Slarder and I hope I will not have to take care of it.
[Included Parts:were they on?
Instruction Manual
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Torque wrench would be nice to have.
View detail
GROM (JC92) BABYFACEEngine slider
The texture of the aluminum base is cool.
I'm not sure how effective it will be in the event of an actual fall, but hopefully it will remain unknown and usable.
It is better to have a suitable tool for loosening to tightening the engine cover bolt on the Right Side.
The Deep socket I had did not make it.
6.I managed with 3 8mmSocket, Extension bar and 9.5→6.3 Conversion Adapter.
Left is no problem.
Ride quality has not changed at all! (Lol)
View detail
Fitted for the first time
It would be nice to have Line and Mark colors other than a little Black. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS Cafe, KAWASAKI Z900RS, KAWASAKI Z900RS Cafe
The simple is best
[How is it used?
I guess it's a good thing to be prepared for an accident before it happens…
Was the one you received as per Image?
Simple and solid product.
Was the installation difficult?
Quantity:Pair (for Left and Right) It was about 40 minutes in
How was your experience with it?
It does not interfere with getting in and out of the car or while driving.
[Included Parts:were they on?
2 Stickers (Parenthesis good.)
[Was there anything that disappointed you?
None
Point of installation and hang/.
As stated in the instruction manual, it is better to work by supporting the body of the vehicle with Jack.
Availability and clarity of Instruction Manual/
It is described as using Jacks and working One Side at a time.
View detail