Reviews
good-looking
OEM is expensive, so we chose here.
I have not yet fallen over, so I do not know how effective it is.
I think it looks good.
View detail
Maybe I don't need Front.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
I thought that the Protector has little protrusion, and since it has a Radiator, I think it is not so meaningful even if it is attached, since it is originally wide.
I hope you don't experience any effects.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
stick out firmly.
I put it on a 2022 XSR900.
Some say it is better not to put it on because it may slip and aggravate the situation, but I assume it will fall over at low speeds.
The back seems to stick out and make sense. I hope you don't experience the effect.
Deep socket 10mm is Quantity:2pc. Set is required, so please be prepared.
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I think it's a good costumer
I think this product is cheaper and more cost-effective than other companies' products. View detail
Wow that's cool
I installed it because I was lonely around the Front.
Circuit also runs, so Protector in the event of a fall.
I hope it will be ??
View detail
I'm not sure how effective it is, but just in case.
The quality of the slider itself seems to be a little small. Well, I bought this Slider just in case. I don't know how well it works yet, and I don't want to know. I don't even want to know.... View detail
BABYFACE Babyface:Axle Protector
It was installed together with the engine slider. View detail
cosmetically ◎
ZX-10R [24] mounted on
Front of 10R is very luxurious even for OEM with brembo and SHOWA.
Damage to the equipment when it stands up and falls over will require significant repair costs,
I put it on as a cane to keep me from falling.
Hopefully the day when they are active will never come.
Material, because it looks good as one point of view, it gives a good sense of customization.
Compared to other manufacturers, it seems to be a little small, but it is not expensive, so it is OK.
View detail
Fits: SUZUKI KATANA, SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
I'll never roll over …
I'm going to install it with the idea that it will look a little better before it falls down. View detail
Fits: HONDA VFR800, HONDA CB650R, HONDA CBR650R, HONDA CB650F, HONDA CB1100RS, HONDA CBR650F, HONDA CB1100EX, HONDA CB1000R, HONDA CB1100
BABYFACE Babyface Axle Protector
I usually enjoy my motorcycle life by riding around town and touring.
This Axle Slider is effective in the event of a mossy accident.
Therefore, we have rated it as ineffective.
This is the first Return in 11 years for the Large type.
This is the first Large type of NAKED.
So, I am riding slowly and leisurely in the spirit of the first time.
As you would expect from Babyface, other companies sell Axle Slider.
I thought it was a very different kind of design.
The only thing is that the Shaft is about 10mm shorter on the CB650R.
And Quantity:Pair (for Left and Right) I want 5mm each.
I would not recommend it to my friends for a moment.
Only about 70% of the Nut has been tightened.
We gave it 4 stars for quality and texture.
I think that's about it in terms of cosmetics.
View detail
Fits: YAMAHA MT-10, YAMAHA YZF-R1, BMW S1000RR, HONDA CBR1000RR, BMW S1000R
Easy detachment!
Rather than a rear slider, the Axle Shaft was installed to make it easier to attach and detach the Axle Shaft.
It can be used as a handle like Doorknob when pulling out shafts, and when inserting shafts, the triangular pyramid shape makes it easy to insert the color, etc. without resistance.
Of course, it would also serve as a Slider, but currently it is benefiting from the detachment process.
View detail
The front is also Babyface to match the engine slider.
For Triumph TRIDENT, Babyface Front axle protector was installed on Tigersport 660 as well as Engine slider.
Although less expensive than OEM products, the appearance and quality of the parts are good, and I think they are reliable parts.
Installation is easy, but I think the attached Instruction Manual is difficult to understand.
Effectiveness is unknown because there are no falls.
View detail
It is easy to install.
This is my first Return in 20 years, so I bought it to prevent standing moss!
Torque wrench is required as 5Nm is indicated for screw tightening
I didn't have one, so I bought a Torque wrench, but I didn't know how to use it, so I took it to a Motorcycle shop and installed it myself while they showed me how.
The appearance is not so prominent, so it may not be enough for those whose main purpose is to dress-up.
I don't know how effective it is because it hasn't rubbed off yet.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000 GT
Before installation, there is a conundrum.
It could not be installed on Axle Shaft as is.
Shaft insert is Quantity:Pair (for Left and Right) Since it is the opposite, the Protector cannot be installed (press-fit) unless it is replaced.
I will have to ask Motorcycle shop to replace the Shaft when I replace the Tire.
(It's a pain to have to pay for labor)
I am very disappointed that I cannot install it even though I ordered it and it arrived the next day.
P.S. I checked MotorcycleCatalogue and all applicable Motorcycles were Nut side Left.
Please note that those who purchase
View detail
Axle Slider
Axle Sliders are sold by various manufacturers, but most of them are black in color, and this was the only one in gold. I am riding a Z900RS SE, and I really wanted a gold color because the front CB400T's tube is gold. It is easy to install. View detail
Exactly what I expected.
I have an external caliper, so I installed it to avoid damaging it as much as possible. It is not as aggressive as the rear slider and does not look bad after installation. It will be installed without any problem. View detail
Axle Slider
Low price, easy installation, and Gold is not available from any other manufacturer. View detail
Fits: KAWASAKI ZRX, YAMAHA FZ1, YAMAHA MT-01, YAMAHA YZF-R1, SUZUKI GSX-R1000, KAWASAKI ZRX1200, SUZUKI SV1000, KAWASAKI ZRX1100, APRILIA RS250 (Aprilia), KAWASAKI ZX-12R, KAWASAKI ZRX1200, SUZUKI SV1000, KAWASAKI ZRX1100, APRILIA RS250 (Aprilia), KAWASAKI ZX-12R
Axle Slider
These are custom parts that only look good.
We have the same Babyface as Frame Slider.
View detail
Fits: BMW S1000RR, BMW S1000R, BMW S1000R
Inexpensive among Front Axle Sliders
[How is it used?
Used as Slider in Front section
Was the one you received as per Image?
It is the same as the photo shown in the publication.
Was the installation difficult?
The installation itself is simple, but the Quantity:Pair (for Left and Right) Which of the following is to be installed as Main?
Check the installation. Check the Instruction Manual for handling.
The part that passes through the Axle Shaft is fully threaded,
It has a rubber tube to prevent scratches, but it is obviously long.
Since it was not possible to install it, the tube was cut and shortened a little for use.
How was your experience with it?
Hopefully not used, as it is effective in the event of a fall.
BABYFACE's Axle Protector was selected because of its proven track record and favorable reputation.
Since the fit is not that great, it is good to be able to wear it in a natural way.
The surfaces are just right.
[Included Parts:were they on?
Handling Instruction Manual available.
[Was there anything that disappointed you?
The resin part is grooved, but it is not chamfered, so if you easily grip it and tighten it,
Easily cuts hands. I think it should be chamfered originally because it is very sharp.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I would like the resin part to be chamfered.
View detail
Fits: HONDA CBR1000RR-R, HONDA CBR1000RR-R SP, HONDA CBR1000RR
I installed Axle Protector for the first time.
Babyface, so it's perfect for Motorcycle as it is.
It was installed without any modification.
Instruction Manual with pictures would be nice.
I think it will sell more.
View detail