![icon-webike.png](https://thimg-afcc.kxcdn.com/@wth-shop/assets/desktop/img/icon-webike.png)
Reviews
![Single Out High Flow Gasoline Cock with Reserve 1/4in NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res6000_image-1_TS.jpg)
PinGelCook
Shipping is on schedule!
I was able to place my order with peace of mind.
View detail
![Plate for 1/4NPT Fuel Cock Adapter](https://img.webike-cdn.net/catalogue/images/2026/adapter_plate_image-1_TS.jpg)
PinGelPlate
It is essential to install PinGelCook. View detail
![Single Out High Flow Fuel Cock with Reserve 1/4NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res6000_image-1_TS.jpg)
PinGelCook!
fcr33πI changed to PinGel to install the carburetor because of the Gasoline flow rate, even though the OEMCook does not interfere with it. The main purpose of this project is for appearance, but… I think it's a good idea.
As other reviewers have mentioned, the hole on the tank side has to be cut down a little to make it larger.
I have wrapped a couple of rolls of seal tape around it and I am happy with it, no gasoline leaks and better parenthesis. If it were a little cheaper, I would have no complaints.
View detail
![Special Offset Plate for 1/4NPT Fuel Cock](https://img.webike-cdn.net/catalogue/images/2026/39-1792_image-1_TS.jpg)
Mk2 with tmr36 and PinGel6000
I installed a tmr36 on a mk2, and the OEM cook completely interfered with the installation, but with a 6mmOffset PinGel6000 mounted slightly to the rear, I was able to complete the installation without any problems. View detail
![Single out High Flow Fuel Cock with Reserve 1/4NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res4000_image-1_TS.jpg)
Dress-up
There are many effects, but OEMCook...
For dress-up because of yabo
Installed. It looks very
Well-organized and satisfactory, but perish Brown bitter Brown
WhiteRust is easy to find.
View detail
![Special Offset Plate for 3/8NPT Fuel Cock](https://img.webike-cdn.net/catalogue/images/2026/39-1792_image-1_TS.jpg)
Used to install Cook by Go Lamp Roducts
Used for Fuel Cock installation by Go Lamp Roducts.
The tank hole was enlarged with a file so that the filter could be inserted, the tank was cleaned, and a fuel fliter was installed after cooking just to be sure.
Tank mounting surface is flattened with oil stone and Liquid Gasket (How to paint Large thing) Seal tape also for use and installation Bolt (Winding Large thing) and Liquid Gasket, and I think I was able to install it perfectly without any blotches after drying overnight.
View detail
![Triple Out High Flow Fuel Cock Racing 3/8NPT](https://img.webike-cdn.net/catalogue/images/2026/triple_racing_image-1_TS.jpg)
External carburetor accompaniment. Indispensable.
In my opinion, it is a necessity for vehicles with external big cabs, but not for normal cabs.
We are using it in Lectron, but Bore up & Big cab Quantities:I feel the need for the first time in Set.
It is not recommended to attach it to a vehicle that looks NORMAL, as it will only cause loss of Reserve and inconvenience.
Well, I don't have to tell you this to those who can maintain MACH…
View detail
![Adapter Nut For 3/8NPT Cock](https://img.webike-cdn.net/catalogue/images/2026/adapter_nut_image-1_TS.jpg)
Fits: KAWASAKI 750SS MACHIV H2 , KAWASAKI 750SS MACHIV H2 [Mach].
![jp](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/jp.gif)
Required when PinGel is installed
Required when attaching PinGelCook
We used it for MACH.
Use less-used water tapes for installation
Buy at Home center.
View detail
![Adapter Nut for 3/8NPT cock](https://img.webike-cdn.net/catalogue/images/2026/adapter_nut_image-1_TS.jpg)
Fits: KAWASAKI Z1-R, KAWASAKI Z1, KAWASAKI Z1000 (air-cooled | KZ), KAWASAKI Z1100 GP B2, KAWASAKI Z2, KAWASAKI Z750, KAWASAKI Z900, KAWASAKI Z1-R II, KAWASAKI GPz1100F, KAWASAKI Z900, KAWASAKI Z750, KAWASAKI Z2, KAWASAKI Z1100 GP B2, KAWASAKI Z1000 (Air-cooled|KZ), KAWASAKI Z1-R, KAWASAKI Z1, KAWASAKI Z1-R II, KAWASAKI GPz1100F
![jp](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/jp.gif)
To KawasakiZ1
PinGelCook and NaturallyQuantity:I bought this in a set. At first, I was worried about getting the right angle because it was screwed in, or if it would leak. I'm glad I bought it. View detail
![Single out High Flow Fuel Cock with Reserve 1/4NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res4000_image-1_TS.jpg)
To KawasakiZ1
I installed this carburetor when I switched to TMR. it has reserve, no lack of flow, and no leaks even after several years of use. If you are replacing a 6mm hose carburetor with an 8mm hose external carburetor, this is a good choice. View detail
![Single Out High Flow Fuel Cock with Reserve 1/4NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res6000_image-1_TS.jpg)
Parenthesis good?
Adapter and Quantity:I bought it in a Set, but Parenthesis got better. View detail
![Plate for 1/4NPT Fuel Cock Adapter](https://img.webike-cdn.net/catalogue/images/2026/adapter_plate_image-1_TS.jpg)
You're early!
PinGel's Fuel Cock and Quantity:I bought it in a Set, but it was a fast response, and Motorcycle became Parenthesis well. View detail
![Single Out High Flow Fuel Cock with Reserve 3/8NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res6000_image-1_TS.jpg)
PinGelSingle outHigh flowFuel CockriReserve with 3/8NPT
When I changed the Carburetor, I replaced the negative pressure type Fuel Cock with a direct type PinGel.
Because the screw part is aluminum, if it tightens too much, the screw mountain is destroyed and it becomes useless.
View detail
![Adapter for Plate 3/8NPT cock](https://img.webike-cdn.net/catalogue/images/2026/adapter_plate_image-1_TS.jpg)
PinGelAdapter plate for 3/8NPTCook
I bought this when I changed my Carburetor to TMR-MJN and when I changed my Fuel Cock from negative pressure type to direct pressure type. View detail
![Foot Grounding Improvement Lowdown Link Kit For KAWASAKI](https://img.webike-cdn.net/catalogue/images/34132/62033_01_TS.jpg)
Fits: KAWASAKI ZX10R (lowers motorcycle 2)
![jp](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/jp.gif)
Lowdown on SS
I bought it because I want to get the whole Forme down the rear a little bit. You can easily replace it by making use of the PANTAHGraph on the car and setting the Rear to Free. The image is lowered by 25mm when the car is not in the car, and it will be lowered further when a person gets on it. I didn't feel any change as far as Touring is concerned because I don't run GunGun in the mountain passes. View detail
![Foot Grounding Improvement Lowdown Link Kit For KAWASAKI](https://img.webike-cdn.net/catalogue/images/34132/62033_01_TS.jpg)
Fits: KAWASAKI ZX10R (lowers motorcycle 2)
![jp](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/jp.gif)
plain
It's not a problem for me. It's not a problem for the accuracy of the product, but the price of the product is unacceptable. View detail
![Adapter Plate Gasket](https://img.webike-cdn.net/catalogue/images/2026/repair_gascket_image-1_TS.jpg)
It's just the right thickness.
This is a must when PinGel Cook is installed. It is made of a moderately thick Gasket, so as long as the bottom of the Tank is not rough or distorted by Rust, there should be no leakage of Gasoline.
If it is still blotting after using this, then either there is a leak from the Screw section or the parallel is not showing on the bottom of the Tank.
View detail
![Single Out High Flow Fuel Cock with Reserve 1/4NPT](https://img.webike-cdn.net/catalogue/images/2026/single_out_res6000_image-1_TS.jpg)
Performance and texture are both good.
It was easy to install. I thought it was expensive, but the texture is very nice and cool.
Just in a few days, Plating got Rust cloudy. It's also very easy to operate.
View detail
![Plate for 1/4NPT Fuel Cock Adapter](https://img.webike-cdn.net/catalogue/images/2026/adapter_plate_image-1_TS.jpg)
Accuracy and texture are good.
I used it for PinGelCook installation. The texture accuracy is very good.
It's easy to install and can be done by anyone, and it's the perfect companion for your fcr.
View detail
![Single Out High Flow Fuel Cock with Reserve 1/4NPT](https://global.webike-cdn.net/photo/impression/1f/1f3287ad6b4ed23b1bc1c33d8812ba24L.jpg)
I love the inconspicuous Black color
I've had a Chrome PinGel on my Motorcycle since I bought it used
Since it's an older car, the OEM Product may have been discontinued and put on as a replacement
About two months ago, I had to replace the tank due to some problems with the fuel sensoretc I went with PinGel in Black, which is less noticeable than Chrome
So far I have no complaints about the features, but as others have implied, On, Off, and I would like to see a sense of click to make the Reserve position easier to understand
Large without any knowledge of it Cook is this But I forgot to turn it off once in the past and made it overflow If there is a compatible product that can be diverted, ManufacturerOEM's negative pressure cooks are ideal
View detail