Reviews
OEM Compatible Filter
Air filters for mopeds, especially filters for slightly older 2-stroke models, are generally made of urethane foam.
This sponge filter deteriorates due to the gasoline component of the blowback, resulting in a terrible condition like that of the STELLA.
This time, I prepared it for the carburetorOH of JOG remote control, which had been neglected for a while.
I worked on it and found that it was still torn up in the air cleaner box, so I quickly replaced it.
Size was also generally usable without any problems.
The difference from OEM is that engine oil and filter oil must be applied since the oil is not soaked into the engine.
In my case, I put about 5cc of engine oil on FilterSponge, put it in a Vinyl bag, and spread it around as if holding it. I applied the oil by squeezing the Vinyl bag and spreading it around.
Too much will cause resistance, too little will reduce the ability to filter sand dust.....................
If you are concerned about it, place it on the ground between sheets of newspaper and step on it after applying it. The newspaper will absorb the excess oil and become a good ambai.
If Oil was applied in the right amount, it would be 5 stars.
View detail
Fits: HONDA APE 50, HONDA GROM, HONDA MONKEY125, HONDA CT125・CT110 HUNTER CUB
Cost-effective Pad
I bought it because it was cheap, and it is a very ordinary pad with performance comparable to OEM.
Life is still unknown.
View detail
Fits: KAWASAKI KX65, HONDA NSF100, HONDA XR100MOTARD, YAMAHA DT50, YAMAHA RX50, YAMAHA RX80, KAWASAKI KX60, HONDA APE 50, HONDA APE 50TypeD, HONDA APE100, HONDA APE100TypeD, SUZUKI BIRDIE50, SUZUKI COLLEDA SCRAMBLER 50, SUZUKI COLLEDA SPORT 50, HONDA XLR80R, HONDA CB50JX, HONDA NSR80, HONDA SUPER CUB 50PRO, KAWASAKI Z125PRO, KAWASAKI KSRPRO
Strong and smooth
It is strong and smooth. Quiet and a good buy! 。 I want to buy the next one. View detail
Fits: KAWASAKI KX65, HONDA NSF100, HONDA XR100MOTARD, YAMAHA DT50, YAMAHA RX50, YAMAHA RX80, KAWASAKI KX60, HONDA APE 50, HONDA APE 50TypeD, HONDA APE100, HONDA APE100TypeD, SUZUKI BIRDIE50, SUZUKI COLLEDA SCRAMBLER 50, SUZUKI COLLEDA SPORT 50, HONDA XLR80R, HONDA CB50JX, HONDA NSR80, HONDA SUPER CUB 50PRO, KAWASAKI Z125PRO, KAWASAKI KSRPRO
For MONKEY125.
Now I am using Non-seal420NZGold made by Daido, this product is GoldSpec. and this Gold amount, from what I saw, the make is good, it is for spare when the Chain made by Daido is no good. View detail
Fits: HONDA SUPER CUB C90, HONDA SUPER CUB C70, HONDA SUPER CUB C50
usually
[How is it used?
To replace Throttle Cable
Was the one you received as per Image?
Yes
Was the installation difficult?
Cable crawling is troublesome.
How was your experience with it?
no problem
[Included Parts:were they on?
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Enough for normal use.
I bought this when I bought my vehicle used and replaced the Pad.
It works just fine, it's not too bad to operate, and it has a Merit that's affordable.
good point
Good enough performance for city riding.
It's very cosy.
Easy to get a bite.
Fast delivery.
A bad point
It is not suitable for vehicles that have been powered up.
If the vehicle is powered up, it will deplete quickly.
It can be used without a problem if it is the degree which added a little hand to NORMAL, and it is the Parts which is never bad.
It works normally, and the controls are not bad.
If you have modified the intake and exhaust, and strengthened the suspension, the brake will be defeated, so you can not recommend to tune the car.
View detail
Fits: HONDA RUNAWAY, HONDA Live Dio Cesta, HONDA LIVE DIOSPECIAL Knife, HONDA LIVE DIOJ, HONDA LIVE DIO, HONDA PAX CLUB, HONDA TODAY, HONDA DIO FIT, HONDA DIO CHESTA, HONDA DIO, HONDA TACT BASIC, HONDA TACT STAND-UP, HONDA TACT, HONDA SMART DIO, HONDA ZOOMER, HONDA SUPER DIO, HONDA GIORNO CREA, HONDA Giorno, HONDA GIORCUB, HONDA JULIO
OEM Equivalent Product, Brand in Japan.
I replaced the front and rear brake shoes with new ones while I was replacing the tires on my moped.
I decided to go with PFP because I thought it would be better if I could get approximate performance for less than half the price of OEM Parts.
Although there are cheaper CHINA non brand at large mail order sites
As you might expect, I have some resistance to Brake Parts, so I chose from Japan's Brand.
I chose it because it came with a Spring, was carefully packaged in a paper Package, and I knew that Motorcycle shops use it for repairs.
The Package says NAO material (Non-asbestosOrganic). I don't think there is any Brake Shoe that uses Asbestos material nowadays, but this NAO is …
1.Compared to other materials, it is more resistant to wear and generates less friction powder.
2.Low aggression, reduced ringing
3.Quantity to weather:Pair (for Left and Right) The performance of the system is not limited by the
4.Spring is included and braking force is stable after shoe replacement.
5.It is also effective at low temperatures and has excellent initial braking power.
I see, it is Perfect ^^^.
Nowadays, OEM Parts are made in Asia. If the quality is the same, the cheaper the better.
When replacing, clean and grease up the brake camshaft, and maintain the cable.
No squeal and I am satisfied so far. I don't know how durable it is so I gave it 3 stars.
View detail
Fits: SUZUKI GSX-R600, SUZUKI GSX1100S, SUZUKI GSX-R750, KAWASAKI ZZ-R400, KAWASAKI ZZ-R1200, KAWASAKI ZZ-R1100, KAWASAKI ZEPHYR1100, KAWASAKI ZEPHYR X, KAWASAKI Ninja ZX-9R, SUZUKI SV1000 SZ, SUZUKI SV1000, SUZUKI TL1000S(97-01), SUZUKI BANDIT1200 S, SUZUKI GSR400, SUZUKI BANDIT1200, SUZUKI BANDIT1250 ABS, SUZUKI GSR600(06), SUZUKI GSX-R400 R, SUZUKI GSX-R400, SUZUKI BANDIT1250 S ABS
It's cosy, but it squeaks.
I had been using SinteredPad and bought this product to replace it. I don't know if it is because I didn't chamfer the surface when I replaced it. Both Dry and Wet braking is as good as it can be, and considering the price, the cost is high. If you don't want absolute braking, it is necessary and sufficient for normal driving. View detail
Fits: HONDA LIVEDio|J|SR|ST|ZX AF34, HONDA LIVEDio|J|SR|ST|ZX AF35
For Refresh
Purchased a new Belt, Pulley and Weight Roller for the Live DIOZx Refresh.
In order to open Crankcase, because it had to remove the Air Cleaner BOX on the structure, I exchanged it in addition because it is the thing of several hundred yen.
I changed it and put it on because it's not particularly different, but it feels better with a new one.
View detail
Fits: SUZUKI TS50W (86), APRILIA 50R S, APRILIA TUONO 50, HONDA TLM50 (83-)
GORILLA at 110.
Cheap, I chose it just for that.
I'm not too particular about the color.
Durability remains to be seen, but I hope it doesn't stretch too fast.
But it's cheap, so you can just buy a new one.
View detail
Fits: HONDA Dio(AF18) Late, HONDA Dio(AF18) Late
OEM same etc.
I don't like the sound of the noisy Power Filter, so I bought an OEMAir cleaner box at Yahoo auctions, bought an Element here and returned to the OEM. View detail
Fits: HONDA RUNAWAY, HONDA Live Dio Cesta, HONDA LIVE DIOSPECIAL Knife, HONDA LIVE DIOJ, HONDA LIVE DIO, HONDA PAX CLUB, HONDA TODAY, HONDA DIO FIT, HONDA DIO CHESTA, HONDA DIO, HONDA TACT BASIC, HONDA TACT STAND-UP, HONDA TACT, HONDA SMART DIO, HONDA ZOOMER, HONDA SUPER DIO, HONDA GIORNO CREA, HONDA Giorno, HONDA GIORCUB, HONDA JULIO
Satisfied
To replace the rear brake shoe 。
I was able to install without problems 。 Does it work as well as the OEM, etc., or a little better?
There is no squealing, and the costuming is very high
This time it was Rear, but I think I'll use this for Front as well
View detail
Fits: YAMAHA TT-R125 LW, YAMAHA YB-1 four, YAMAHA YB-1 four, YAMAHA YB50 four, YAMAHA GEAR BA50, YAMAHA GEAR, YAMAHA MATE V50 D, YAMAHA MATE V50 D, YAMAHA MATE V50 D, YAMAHA MATE V50, YAMAHA MATE V50, YAMAHA MATE V50, YAMAHA Newsmate V50N, YAMAHA Newsmate V50N, YAMAHA Newsmate V50N, YAMAHA Newsmate 90, YAMAHA Newsmate 90 T90N, YAMAHA newsgear, YAMAHA News Gear (4ST) BX50N, YAMAHA News Gear BA50N
Cospa strongest
I was worried about it being cheap, but it's nothing to worry about
It will stop
Brake noise sometimes occurs after rain
I don't know how long it will last, as I've just started using it
View detail
Fits: SUZUKI Birdie4ST Burden|FB50L, SUZUKI Newspaper Birdie4ST|FB50P, SUZUKI Newspaper Birdie4STG|H|FB50PH, SUZUKI EPSILON 150 Newspaper Birdie2ST, SUZUKI DF200 DJEBEL, SUZUKI DF200 DJEBEL, SUZUKI DF125 DJEBEL, SUZUKI Volty type C TU250, SUZUKI Volty type C, SUZUKI Volty type I TU250, SUZUKI Volty type I TU250, SUZUKI Volty type I TU250, SUZUKI Volty type I, SUZUKI Volty type I, SUZUKI Volty type I, SUZUKI Volty type II TU250, SUZUKI Volty type II, SUZUKI Volty type T TU250, SUZUKI Volty type T, SUZUKI MARAUDER250
good
The DF200 DJEBEL's Rear brakeTouch
We've got some complaints
I replaced it with a PFPBrake Shoe
Low cost but acceptable for use
Compared to the OEM Product, the aluminum shape of the body is
Reduction in cost?
I'm a little nervous about the look and the strength of it, but …
There is no problem for now
BrakeTouch is a little lighter than the above
Brake works well
View detail
Fits: HONDA SUPER CUB F, HONDA SUPER CUB F, HONDA press cub, HONDA Spacey 125, HONDA FTR223, HONDA Super Cub 110 F, HONDA press cub, HONDA Spacey 125, HONDA FTR223, HONDA Super Cub 110 F
I chose it because it was less expensive
It was a replacement for the OEM Product, but I chose it because of its low price Fee Ring-wise, it is very normal It is not enough to lock even if you apply the full rear brake
The OEM Product we replaced still looked like the Shoe, but the Dust, etc It was not working well By the way, the first exchange at 65,600?
Now, I hope it's durable, but the next time I'm going to replace it, I'm going to say a little sooner, but it's about 20,000 miles Isn't it?
View detail
Fits: HONDA SUPER CUB, HONDA SUPER CUB 50, HONDA SUPER CUB 70, HONDA BROAD 90, HONDA LEAD 100 NH100, HONDA LEAD 100, HONDA LEAD 50, HONDA LEAD 90, HONDA CABINA, HONDA CABINA 90, HONDA read, HONDA broadcloth, HONDA dachshund, HONDA Shirley (6V), HONDA Shari (12V), HONDA Shirley 70, HONDA Gorilla (12V), HONDA CB70, HONDA CD90, HONDA R&P
Good at low price
There is no problem for minutes to ride normally.
There was no fear of Touring of about 100 km.
It is a satisfactory product that you can perform mounting without incongruity.
View detail
Fits: HONDA GB250 CLUBMAN, HONDA ToRAN Salve 600V, HONDA CUB PRESS, HONDA XL250 S, HONDA XL250 R, HONDA NX650Dominator, HONDA CBX250 RS
OEM Product and the like. Effectiveness, low price but no complaint
【What made you decide the purchase?】
The price was the cheapest in Brake Shoe that conforms to a favorite car
【How was it actually used?】
The effect is almost the same as OEM Product. Only the stepped and stepped buns will work.
I exchanged it with the OEM Product's remaining amount still, but the experience did not change before and after the exchange.
【Was it difficult to install? (Hard parts case)】
I did it at Tire exchange specialty store. (The wage is 3,240 yen including tax, about 10 minutes required)
【Please tell me the point of installation and hang (in the case of Hard parts)】
Removing Brake dust that has accumulated over the years with Parts cleaner
[Is there anything I was disappointed about?] Nothing in particular
【Hope for Manufacturer - Please let me know if you have any improvement points]
I thought that it would be good if I was attached with durability and the presence or absence of use of Asbestos, etc. on the material side and performance comparison table etc
【Have you compared items?】
KITACONon Fade Brake Shoe, NTB products
[Others]
It is a product with high Cost performance, no problem in terms of performance as it does not change from the original OEM Product
View detail
Filter made by Air Purifier
Intake air filter of the air cleaner made it for own production to stop production. Adhered two sheets of Filter, cut it according to the shape of the original Filter base, and glued. Since the eyes are slightly finer than the original Filter, garbage exchange is good. It is satisfactory that it can be repaired cheaply, although it is not purposeful.
View detail
Fits: YAMAHA JOG 3KJ, YAMAHA JOG 3RY, YAMAHA JOG 3YJ, YAMAHA JOG, YAMAHA APRIO, YAMAHA VINO
OEM TypeAir Filter
【What made you decide the purchase?】
It's cheap price anyway.
【How was it actually used?】
In a good way, there was no particular impact.
【Was it difficult to install? (Hard parts case)】
Depending on the type of car, it is easy to just remove the Air cleaner box. However, if it is an old car that does not maintain much, it may be hard to cure Nozzle to Carburetor.
【Please tell me the point of installation and hang (in the case of Hard parts)】
The Air cleaner box is sticky with Oil due to the repetition from Carburetor. Hand washing is easy with Gloves for oil-impermeable work. Also, neutral detergent is more economical to clean Air cleaner box than Parts cleaner. I think it would be better to have Brush and Bucket with hot water in winter.
[Is there anything I was disappointed about?]
I feel that it is somewhat thin. I feel that elasticity is also weak, but I think that it is not a problematic Level.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Where I want thicker thickness a little.
【Have you compared items?】
Degraded OEM Product. It became fragile and easily torn apart.
[Others]
Air cleaner box fits 3KJ ProductNo vehicles.
If you want to know if it fits your own vehicle, it is easy if you check if the 3 KJ stamp is on the lid of the Air cleaner box.
View detail