Reviews
as a stake in a difficult situation
I'd hate to run into a situation where this is in play.
Installation is easy, as the Instruction Manual includes a description of the torque to be tightened, so as long as you have a torque wrench, you can work without anxiety.
I like the inconspicuous color and design that blends in with the car body.
View detail
Fits: HONDA CBR929RRFire blade, HONDA CBR954RRFire blade
If you're going to run Circuit, you can have it.
Slider to slide the vehicle body in the event of a rollover.
I think people usually put it on for Cowl protection, etc., but I don't recommend it for this purpose.
This is because the Slider is naturally located at a place that protrudes from the body of the car.
If the slider falls from a low position, such as while cornering, there is no problem. However, if the slider is in a high energy position, such as when it is standing up, and its kinetic energy is zero (i.e., the slider receives all the impact), all the energy will be applied to the slider and its attachment points, and as a result, there is a possibility that the frame or engine mount may crack. As a result, there is a possibility that the frame or engine mount may crack or other troubles may occur.
It may also increase the possibility of running into the roadside or GuardRail on public roads since the purpose is to slide the vehicle body.
If you want Cowl protection, etc., you can put it on, even with that Risk...
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Works well for the price
If you want a stand hook roller that would look like an original equipment of the bike, you can consider this one from Moriwaki. It is just that it is too plain and simple, I wish they were able to put the Moriwaki logo in this roller. View detail
Circuit has drastically reduced fall injuries!
The installed Machine is VTR250FIMODEL.
This Skid Pad was extremely effective the other day when I tried too hard on Circuit's HairpinCorner and fell over (of course, it would be better if I didn't fall over ^^;)!
The Skid Pad kept the machine from sliding down to the label and prevented the rear end of the machine from getting caught up, and also kept the machine's damage to a minimum. The damage is shown in the photos and details below.
Bar End Sharpen.
Clutch lever slightly bent and shaved upward (works fine except for a little discomfort)
Change Pedal tip shaved and bent (I bent it back by hooking it with a Glasses Wrench, and it worked fine.)
Footpeg is Foldable, so almost no problem. No need to replace.
The tip of the Swingarm Stand Hook for VTR250 made by Babyface was shaved off. There is no damage that needs to be replaced.
I can say that the Skid Pad is the gold standard for the VTR250's original robustness. Of course, it will definitely perform well on public roads as well (of course, it would be better if it didn't).
*Repair Parts was available at Webig and I only needed to replace the tip. The shipping was faster than I expected. Thank you!
View detail
Stand Hook of your dreams
Used on a CBR600RR PC40 vehicle with diverted Swing Arm.
Before the Swing Arm was diverted, there was no Stand Hook boss, and an L-shaped maintenance stand was used.
To begin with, none of the motorcycles I have owned so far had stand hooks, and it was one of the parts that I had been longing for.
I was humiliated when every Maintenance Stand I tried to rent was a V-shaped receptacle…… lol.
By the way, I have heard that Honda cars are Large Residential M8.
Of course, the CBR600RR PC40 was also compatible with the M8Type.
Stand HookBody is Anodized Material:I think it is Aluminum.
Bolt is Material:It was a Stainless Steel hexagonal Flat Cap Bolt.
Installation should take less than a minute.
It feels good to use, and I had some doubts about whether it would be that convenient. I had some doubts, but this is certainly convenient.
I definitely feel less nervous and cold sweat when I hang the maintenance stand by myself than when using the L-shaped receptacle.
I feel that the bending of the receiving parts of the Maintenance Stand is somewhat less than that of the L-shaped receiving parts (or is that just my imagination?). (Or is it my imagination?).
I now understand a little more about people who put bosses on Swing Arm even if they have to weld them on afterwards.
Quantity for at least Stand Hook:Pair (for Left and Right) to jump out, so I am wondering what the impact would be in the event of a fall.
Sometimes I see vehicles that are bent or bent …….
Well, if you care, you will lose lol.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SF
Thank you for your help.
I have had it on since I took delivery of my Motorcycle 6 years ago and it was a great help when I took delivery of my car. Thanks to this SkidPad, my engine was not scratched even though I was often standing on the road when I first got the bike. It is not as strong as the Engine Guard on the learner's car, but I think it helps a little against standing bumps, etc. I am thinking of adding an Engine Guard just in case, so the time may come for me to part with it soon. I have not had any problems with standing up in the sun recently, so I don't have to use it, but I think that's the best thing. Unlike cheap Chinese products, it doesn't look cheap and I like it because it looks OEM. I think it was probably OEMOption at the time. View detail
Engine slider in case of a mishap
This product is simpler and more cost effective than the standard Engine Guard.
It is simple, so installation is very easy. It is suitable for beginners.
View detail
Engine Guard
It's not just an Engine Guard product, it's simple and very cost effective.
Easy to install.
View detail
Trusted Brand and UserFriendly Support
MORIWAKI is a long-established and reliable brand. 。 The installation instruction manual is easy to understand, and if you only want to replace the skid pad, you can order it by the piece, which is a user-friendly and reliable brand. View detail
Practical &Parenthesis Goodness.
I saw the same vehicle on at my favorite Motorcycle shop. I bought it when I found out about it. It's a Plus for looks and practicality. View detail
How to use MORIWAKISkidPad
It is easy to install and you can drive safely when touring. View detail
For when the time comes, …
The instructions were a little confusing, but it was easy to put on. View detail
Mounted to fit the Sub-frame
I installed it to match the Sub-frame.
I hope I won't have to take care of you and I'll ride carefully.
I also added Posh's Engine Guard with Plus.
View detail
keeping the same shape
As for the installation, even an amateur can install it easily. The reason why I gave it 1 Minus is because I didn't realize there was a Nut on the other side when I tightened the Bolt. I think there is an instruction manual for each car model, so please write that there is Nut. I think this is a good parenthesis, and it does not spoil the original shape of motorcycle. However, I would like to drive not to use this. View detail
Fits: HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF
All Product Contents are sold as Repair Parts.
CB1300SBSP (2021) It is attached to the
It is also worth mentioning that all Product Contents are sold as Repair Parts, which is rare in Aftermarket parts.
It's one or the other that gets mocked, right?
Also, it does not interfere with the design of the vehicle body when installed, or rather, it does not ruin the design of the vehicle.
I once spoke with someone in the sales department who told me that Quantity:Pair (for Left and Right) The length is different in the Pad of the
If it is too long, it may affect other places, and they have designed the balance when it falls down.
It may have that kind of functional beauty.
It is important to use a torque wrench when installing the Slider. Be sure to use a torque wrench.
The tightening Torque listed in the attachment is 44Nm for both Base and Pad.
In particular, the Base attached to the Frame must be used with the Torque wrench or the Quantity:Pair (for Left and Right) You'll be changing the yaw of the
View detail
Mostly satisfied!
[How is it used?
I use it on my YZF-R25 which has been converted to Racer.
Was the one you received as per Image?
It was just like the Image! You can feel the aluminum from the image, so Material:I thought it was Aluminum.
I guess I just thought it was lighter than I thought it would be.
Was the installation difficult?
If you have the Hex tool, it only takes a minute or so to complete the swap!
How was your experience with it?
It's slim and doesn't interfere with the Stand Hook, which is nice.
The previous Ethos had a thicker hook and would catch when you had to STAND on it.
So I chose this slim one from MORIWAKI EngineerRing.
To be honest, it was also cheap. (Laughs)
[Included Parts:were they on?
It comes with an M6 countersunk screw.
[Was there anything that disappointed you?
Not at all!
View detail
I installed it on my 2021.
The hole punching stencil included with the package was useless for the '21.
The hole is drilled with a 22mm hole saw, and the hole is widened slightly with a Leutor Large→ If the hole is not widened, the piece for tightening will not fit.
Torque management is a must for this engine, as it doubles as a fixed Bracket Bolt.
Required Tools
53Nm available Torque wrench
22-24mmHole saw
Leutor for hole correction
The above is a must. If you do not have the tools, please have them installed at a motorcycle shop. If you have the tools, you can install it on the 2021 New Model CBR600RR by yourself.
The texture is great, I deducted one star because of the difficulty of installation.
It is better to remove the Under Cover first before working on it.
View detail
Buy Black
Exhaust System is Moriwa Short Tube.
I've got it all lined up.
No complaints about the price.
I have no complaints about the quality.
Is the Large sturdy even if it falls by installing it?
I don't know.
I don't even want to see the effects of the installation.
I'm going to do my best not to fall down.
View detail
Low price and solid
[How is it used?
Normal installation and use.
In the event of a fall, it reduces Damage.
In fact, I've been helped.
Was the one you received as per Image?
Yes
Was the installation difficult?
No
How was your experience with it?
OK
[Included Parts:were they on?
As many as you need.
[Was there anything that disappointed you?
None
Why doesn't this come with the Standard when new?
View detail
It's better to put it on.
I bought it after seeing a vehicle with it installed.
The price was very reasonable and I installed it immediately after purchasing the Motorcycle.
It is installed at the same time as Sub-frame.
I think it looks powerful and good.
I've never fallen over, so I don't know how effective this is, but I'll be careful not to feel the effects!
View detail