Reviews
I love it.
The Large is very good and I use it for Oil change trips.
There is no problem in particular, but if I may be so bold, it would be helpful if the paper could be folded easily.
View detail
Let's use it for Oil exchange!
When replacing oil, it is easy to fail to catch the oil if the waste oil is thrown away, but with this, it is safe.
There is no such thing as a failure and overflow.
It makes a difference whether you have this or not, and you can replace the oil with confidence!
View detail
Easier to grip
I used to use Emon's Air gauge, but when I put it away, I accidentally closed it without removing the Air gauge and the gauge stuck and would not return to Zero. View detail
It looks like it will fit in the stated capacity.
2.The product is up to 5L, but it seemed like a Limit at about 2.3L.
It's in there with no problem, so it's supposed to be in there as described.
It's much easier to dispose of than the previous Dan Ball box was.
View detail
I am afraid of Short and I love it!
I love it because I had a scary experience with it once when I was changing batteries on my Motorcycle and I had to short it out! It is a little on the Large side for Motorcycle use, but I have no problem using it! It is a little bit Large for Motorcycle use, but I can use it without any problem! I am very happy with this product! View detail
Purchased oilfor replacement for ninja1000
Items necessary when changing oil.
It can be disposed of as combustible trash as it is.
I think I will continue to Repeat Emon because other Manufacturers are expensive.
The only drawback is that the Oil will ooze out and if you don't double wrap the Vinyl and dump it, the rest will look Large weird.
View detail
For continuity checks
I purchased this to do a continuity check during Restore.
I usually use Tester, but with Tester I have to suppress both and my hands are full.
I have an Alligator Clip, but I bought this Inspection Tester because I thought it would help me do a lot of work.
If you clip one end to the Earth terminal, you can easily check for continuity, so it is quicker to find out what wire is what for each wiring.
The line is also long, so it is unlikely to be unreachable.
The good thing is that I have both 6V and 12V cars, so this one pc can provide both.
It is useful to have 1 pc for TroubleShoeing in Wiring.
View detail
Lining Peeled Off Tool, but also useful for peeling off the exterior
The product name is Lining Peeled Off Tool, but it is also useful for removing the exterior.
There are two types of shapes, and the principle of leverage makes it easy to apply force, but it is likely to break if force is applied too much.
It's better to break it before the exterior cracks, though,
PushPins and other difficult-to-remove items can also be removed.
When using the product, cure the contact surface with Curing Tape, etc. before use.
View detail
Where Solder is connected, etc.
It can be used for branching connection with a solder, protection of Cable, etc.
It would be better to shrink them with a heat gun, but they are shrinked by lightly frying them with a lighter.
Be careful not to put the flame too close to it or it will melt.
View detail
Used for Wiring processing
After all, using a decent tool will ensure a clean and fast completion.
This is one product I wish I had bought earlier.
View detail
put together in a presentable manner
Recent Small blinker wiring is ultrafine
It's as if it would tear into a thousand pieces if you applied a little too much force.
If you attach it as it is, it will surely break off.
And it looks bad Parenthesis.
So I reinforced it through Tube.
Finished by decorating with an Amigumi Sleeve
Just this much will make it look so much better.
It's definitely better than the BlinkerWiring roundup.
View detail
Trust.
It claims to be weather resistant, so trust it anyway.
I have always been an Emon believer.
… I don't think it's any different than the others, … (laughs)
2sq for Grounding Wire.
View detail
1pc. is useful for various purposes
[How is it used?
I bought it to use as a Drain pan for Oil change.
Oil replacement
Chain cleaning
Parts and tool storage for replacement of OthersParts
It is used for
Was the one you received as per Image?
I thought it was smaller than I expected, but considering that I was going to put it under the belly of the Panigale, 5LiterSize was just right in terms of Clearance.
How was your experience with it?
Oil replacement
In the case of Panigale, it produces about 3.5 liters of waste oil, but the weight of the oil causes it to deflect quite a bit.
There is a scale, but it cannot be used as a scale because there is only a line in one place.
Chain cleaning
I also use it as a receptacle for chain cleaner during chain cleaning. the size is just right and the area around it is now dirt free.
Parts and tool storage
When replacing or removing parts, it is easy to keep bolt nuts, etc. in the box and organize them without losing them.
[Points to note]
Material:It's not like a Stainless Steel pan or something, so I think it might deflect and spill if poured in parallel.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
It's strong enough.
In order to use the Portable navigator mounted around the Handlebar and the DriveRecorder (DAYTONA DDR-S100) mounted on the Rear as a Mobile Battery drive, it became necessary to install a Mobile Battery around the Handlebar. The need arose to install a mobile battery around the handlebar.
I wanted to be able to easily attach and detach the Mobile Battery, so I attached the mount of REC mount+ to the Handlebar Brace and attached the Attachment to the Mobile BatteryBody to be able to use it. I wanted to use an existing Attachment, so I decided to use a Smartphone Holder that I had left over.
I had a double-sided tape of 10mm width, so I could use them side by side. I had 10mm wide double-sided tape, so I could use them side by side, but I thought a single piece would be more secure, so I bought this Seat type.
Since it is for in-car use, it may not be good in the rain, but I don't ride in the rain, and since the Mobile Battery is not waterproof to begin with, and I intend to remove it as soon as it rains, I consider rain to be of no concern.
There is nothing special about this ordinary double-sided tape, so all you have to do is cut it out and paste it. The only things I took care of were to wipe the surface to be attached, this time both Mobile Battery and Attachment, clean and degrease them, and to work so that the tape would be attached in one shot to the targeted position. I also made sure to apply the sticker in one shot at the target position.
The price may seem high for the Size, but it is securely attached, so I don't think I will drop it while driving.
View detail
It's firmly attached.
I had a 10mm wide tape and could have attached it side by side with sufficient strength, but I decided to purchase the Seat type because I thought a single piece would be more secure.
Some products are labeled as heat resistant, but this product is also heat resistant. Operating temperature range -20 to 150 degrees Celsius. The product is designed to withstand even midsummer in a car.
This product is slightly thicker, and its elasticity and neSpringba make it more difficult to cut out, so the cross section will be rough if you do not work carefully with a well-cut Cutter.
The adhesive is strong enough. As a basic rule, degrease the surface to be pasted firmly, and work to paste it in one shot at the targeted position.
The price seems high for Size, but it doesn't seem to fall off while driving.
View detail
Powerful
I needed to reattach the Bracket to attach the Camera to the Helmet and purchased the Seat type.
I have been using a bracket of the type that can be attached to a rec mount in order to operate a Camera that is used as a DriveRecorder by attaching it to a helmet. Previously, I was using DAYTONA's DDR-S100 attached to the helmet, so the Bracket was originally attached, but it was removed when the helmet was repainted, so it was necessary to prepare double-sided tape to reuse the Bracket. To reuse the Bracket, we needed to prepare Double-sided Tape.
Since it would be very dangerous if the Camera were to fall out of the helmet while driving, we decided to use a strong double-sided tape and a single piece of double-sided tape.
If it is for the inside of the car, we had Seat type Double-sided Tape in stock, and it seemed to have enough adhesive strength, so we thought about using what we had, but since we cannot say that there is no possibility of driving in the rain, we purchased Double-sided Tape for the exterior that seems to be strong against wind and rain, just to be safe. However, since there was no guarantee that I would be able to run in the rain, I decided to purchase double-sided tape for the exterior that would be resistant to wind and rain.
Since this product is rather thick, it would be better to use a cutter that can cut well when cutting it out. In addition, although it is a basic thing, I think it is better to clean the surface to be pasted, to degrease it firmly, to paste it in one shot at the targeted position, and not to mess with it for about one day because it is not firmly attached immediately after being pasted. As for the cutout, the cross section was rough because it was inevitably cut by hand, but generally, I think it was pasted in a good way. Since it is firmly attached, it is unlikely to be dropped while driving.
The price seems high for Size, but I am satisfied with the results as expected.
View detail
Recommended for Full Cowl Motorcycle!
Since my car is a Full Cowl, I have used many different Lining Peeled Off Tools to remove the cowl, but this product is very easy to use! I like that the resin used for the handle is different from the material used for the peeled-off part of the gold part! It is quite sturdy and I think it will last for a long time! View detail
Light and affordable Large size
It is light, reasonably sized and inexpensive, so it is very useful. View detail
Changed to new Package. No stickiness!
I bought this product for a friend of mine because the Vinyl Tape I had been using at the 100 yen store was sticky, so I used it for the wiring process on my Motorcycle Navigation! It's sticky but not sticky! It's easy to cut with scissors!
This is a product I will continue to use for years to come!
View detail
Required for Coupler processing in Blinkeretc.
[How is it used?
I purchased this product because I wanted to use the same terminal as the OEMCoupler instead of the Bullet Type Terminal connection when attaching an external Blinker.
How was your experience with it?
It works fine. If it were a little more expensive, the feel would be better, but for this price range, I have no complaints.
The BlinkerCoupler for Kawasaki cars is essential, as it can only be fully crimped with Electric Works Pliers for fine wire.
[Points to note]
0.This is for 3sq or smaller only. Please be careful not to use it for other standard items as it may lead to wire breakage or damage to the tool.
How did it compare to other products?
It's neither too good nor too bad. It is inexpensive and easy to buy.
View detail