Reviews
It was just like the image.
I have just purchased a DDR−S100 with KAMUI3 for the purpose of fixing the Wiring to operate it as a HelmetCamera.
My DDR−S100 was modified to be able to cut the cord in the middle and connect it with Waterproof Coupler after the USB cord was disconnected. The third image shows the Helmet side. By connecting the other side of the cord connected to the Mobile Battery to this side, the cord does not get in the way when attaching and detaching the Helmet.
This time, when I use KAMUI3 for motorcycle commuting, I thought it would be better to have a DriveRecorder, so I decided to install DR−S100 on my helmet, and selected this product as just the right one to fix the Power Cord.
This 3mm TubeHolder was not bad looking and had just the right diameter to move it a bit against the thickness of the Wiring.
I have used 5mm diameter ones in the past, but they can also be cut and used, and I think they are quite user-friendly Parts. However, the adhesive strength is not very strong, so you need to be careful where you apply it. If it comes off, I will reapply with a stronger double-sided tape.
View detail
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Service Reminder Reset for New Model GSX1300R HAYABUSA
[How is it used?
Recently, many manufacturers have adopted a system in which the Lamp on the Meter lights up when it is time for maintenance.
Various foreign car manufacturers, especially Ducati, are doing this.
But recently, domestic cars are also becoming like that:you have to drop Gold to the Dealer to get rid of the Lamp. Is this part of the Dealer's business strategy? So, even for a simple oil change, if you don't go to the Dealer to have it done, the maintenance Lamp is still glowing all the time.
is Japanese pampas grass, a simple homemade one is all that is needed to solve the problem.
Was the one you received as per Image?
As per Image
It's better to buy it with other things. Since it's only about $100 anyway, the actual store is a better deal when shipping is included.
How was your experience with it?
Effective.
[Points to note]
You have to insert it deep to get it to work.
How did it compare to other products?
Nothing in particular to compare.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
In doing the work, this method is probably a maintenance procedure that is not covered under warranty.
If you want to be stingy with your Gold, please use it only as a reference.
If you are a little worried about the work, you should still buy the OEMReset switch.
OEM reminder Reset switch
09930-83130 Available at Webike, but currently out of stock?
By the way, in most cases, they fail.
It will not respond unless it is inserted firmly and deeply.
Then press and hold the LeftSelectSwitch▼Button to open MENU, select SERVICE, MODESwitch to determine RESET, which is not usually displayed, select Yes when Yes/No appears, and then you can set it individually!
View detail
For ServiceReset
Recent SEA BASS cars have a sign in the meter reminding the driver to change the oil.
I thought the only way to erase it was to have it reset at the shop, but it was easy even for an individual.
The connector hole was too small and the needle gold was too thick to fit in the connector, so I used Emon terminals.
OEMs sell specialized products, but they are expensive, so this was sufficient.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Used to extend BlinkerWiring
Used to extend the Right Side wiring as it was too short when replacing the Rear blinker.
Naturally, we were able to extend it without difficulty.
View detail
For Wiring processing
Purchased for use in Wiring process. No problem. View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Frosted Material with high texture
I used this product to wiring up my Ninja250SL's sub-computer and USB. Honestly, you can use Curing Tape instead of this product, but this product is pre-cut, so it is easy to work with, and it looks overwhelmingly good, so it is a Recommendation! View detail
My savior who mistakenly cut off CUB's Wiring
I bought it because I had mistakenly shibered CUB's RegulatorWiring.
The shape is exactly the same as the Coupler of the C50OEMRegulator.
However, please note that the OEM is like a double cord, so the attached terminals cannot be used.
View detail
Motorcycle Wiring Essentials
This is a must-have item when placing a Relay on the Seat and extending the wiring from under the tank, through the Engine sturdy, to the Handlebar on the Front. It protects the wiring from rain and heat and prevents unnecessary troubles. View detail
Emon for peace of mind
I bought it because I want to stop Bullet TerminalWiring for good.
Various Wiring teasers are Quantity:It might be better to buy a Set, but I think buying Rose is a better deal at the moment because you end up with a surplus.
View detail
By Location!
When wiring, Wiring Tube is used for the wiring itself, and Coil type Wiring Bando is used for the Bullet Type Terminal and the Jack portion. The Wiring type is easier to use than the Tube type for these joints because it is easier to remove immediately. View detail
Wiring Summary!
The Wiring Tube is a good product for refreshing the wiring, because it is hard to tell which is which when you're wiring and it can cause stress buildup. View detail
Replace with new Connector
The Coupler I was using was discolored and hard to remove, so I purchased a new one to replace it.
Male, MeSpin, and Coupler set items were inexpensive and saved me a lot of money.
View detail
Wire standards
Both EmonAV1.25sq and DAYTONAAVS1.25 are probably stranded wires, but Emon has a thicker and softer coating, while DAYTONA has a thinner and harder coating, which is said to be similar to OEM harness. Incidentally, "sq" stands for "Square," and "AWG" is called "Gauge" (AmericanWire gauge) in the United States wire standard, indicating the cross-sectional area of the conductor section. AWG16 = 1.25sq = 1.31mm2. The larger the AWG number, the smaller the cross-sectional area. If it is just 1.25 and only a number, it may be the diameter of the conductor, but is there any diameter notation for stranded wire? View detail
Connector Replacement
The MotorConnector installed is old and discolored, so we are purchasing a new one for replacement.
The TAB, receptaclePin, and Connector set was reasonably priced, but I was able to exchange it for a new one.
View detail
Very inexpensive.
I would like to install a new Grip heater, but I would like to calculate if the heater is Large enough to interrupt the wiring between the USB port and the Relay. The maximum charge current of the two electrical components is 3.3A at 13.5V for the Grip heater and 4.8A at 5V for the USB2 Port (5V is switched on and off), totaling 8.1A. I bought Emon's AV1.25sq. The available power is 140W or less for 12V cars and 280W or less for 24V cars. If converted to allowable current, it is about 11.6A? Although it is within the allowable range, it is not as high as DAYTONA's AVS1.25 (A) of the same size.:Auto for Vehicle Low Voltage Power Line, V:Vinyl、S:The price is 1/8th of DAYTONA in unit length, and Emon is very cheap. By the way, it is another Wiring, but the most large current of ETC on-board unit seems to be less than 1A because it is 1AFuse, although only standby current was written. View detail
Wiring as usual
[How is it used?
I had been using it for wiring work and bought it at Home centeretc. when I noticed it, but I ran out and had plans to shop at Webike, so I bought it along with the other products.
Fine wire 0.5sq is used for those with low power consumption, while Others basically use this 0.75sq.
[Was the product you received as Image?
It was just like the picture.
I always use the safe Black Wiring.
How was your experience with it?
This is a standard Wiring Cord, so the product is solid.
Emon's Wiring Cord allows you to hook up excess wire with the Holder, so you don't have to worry about it being RoseRose the next time you use it.
【Review】
It is inexpensive, readily available, and of consistent quality.
It is also convenient to keep Wiring together.
I always use Emon's Wiring because it has no problems with heat resistance, oil resistance, etc. for use on motorcycles.
View detail