Reviews
It was just like the image.
I have just purchased a DDR−S100 with KAMUI3 for the purpose of fixing the Wiring to operate it as a HelmetCamera.
My DDR−S100 was modified to be able to cut the cord in the middle and connect it with Waterproof Coupler after the USB cord was disconnected. The third image shows the Helmet side. By connecting the other side of the cord connected to the Mobile Battery to this side, the cord does not get in the way when attaching and detaching the Helmet.
This time, when I use KAMUI3 for motorcycle commuting, I thought it would be better to have a DriveRecorder, so I decided to install DR−S100 on my helmet, and selected this product as just the right one to fix the Power Cord.
This 3mm TubeHolder was not bad looking and had just the right diameter to move it a bit against the thickness of the Wiring.
I have used 5mm diameter ones in the past, but they can also be cut and used, and I think they are quite user-friendly Parts. However, the adhesive strength is not very strong, so you need to be careful where you apply it. If it comes off, I will reapply with a stronger double-sided tape.
View detail
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Pricey but convenient for beginners
I think it is very convenient for amateurs to connect Motorcycle wires such as Blinker or Tail lamp. First, strip the cord, twist the wire that appears, insert it into the hole in the plastic part of this Connector, and snap it with pliers or something, and you have One Side. Do the same for the other side. The finished products are made of Male and Female, so you can connect them properly by plugging them into each other. It is an excellent product. However, if it is difficult to connect the wires, it is of course useful, but if you have a spacious place and have some room in length, I think it is best to put a solder on it.
The price is high and the cosmetics are not so good. But I think it's useful if you're in a hurry, a very beginner, or in a small space.
View detail
Frosted Material with high texture
I used this product to wiring up my Ninja250SL's sub-computer and USB. Honestly, you can use Curing Tape instead of this product, but this product is pre-cut, so it is easy to work with, and it looks overwhelmingly good, so it is a Recommendation! View detail
Installed in Motorcycle yard.
I installed it in the parking lot for my motorcycle in my small yard on the way home from touring. It is very sturdy so even if I ride up on it with my motorcycle it doesn't scare me! It also contributes to safety as it reflects the light and shines well! The double-sided tape on the back has good adhesive strength and does not come off! View detail
Durable!
I put one on the back of my car and the rest at the entrance to Garage. I scraped it on the ground once when I fell over, but it was strong and only got a few scratches! It's a great job and it's a Recommendation! View detail
A bit expensive but high quality! Be safe!
I have experienced an accident with a child, so I put this product on my Rear Bag for safety first!
I feel that the number of times I have been forced to close the distance between cars has decreased since I completed the application! Safety first! I will be an active Rider for life! This is a recommendation!
View detail
If you're willing to rip it off, be careful.
Items convenient for products that also have a protector, so even if they are attached to protect scratches, they look like they are attached to improve visibility.
However, when peeled off, it left a mark and was a type of adhesive that was difficult to remove even with Seal peel, so I recommend using another double-sided tapeetc. if you are thinking of peeling it off.
View detail
Thick enough! Reflects well too!
We were looking for a reflective Sticker to improve safety. At first, we were looking for a reflective Sticker sold at a hundred-yen store.
I was dissatisfied with the adhesive strength and stuck this product on it.
I am satisfied with the results! When degreased properly, it does not peel off even if it rains, and it reflects the light of following cars perfectly.
It contributes to safety improvement! It is easy to apply, so it is a recommendation for everyone!
View detail
Finally, it's time to go.
I purchased and installed a Push Type Switch to use as a switch for the power supply of the car navigation system, but the other day, when driving on a mountain pass with somewhat rough pavement, a malfunction occurred due to vibration, causing the power supply to turn off and on, and temporarily Navigation repeatedly started up and stopped functioning.
This symptom did not occur during normal city driving or on well-paved roads, even on mountain passes, so I think that the problem may have been caused by severe vibrations that exceeded the manufacturer's expectations. I think that the previous Push Type Switch may not be good at strong vibrations. I don't want to continue to use the switch in this situation and have navigation problems, so I decided to replace it with a toggle switch that I have and see how it goes.
I bought this toggle switch but never had a chance to use it, so it has been sitting in my inventory for a long time. I haven't tried it in a place where it would vibrate yet, so I don't know how it would work in a similar situation, but I like the way it looks, so I'm glad it works.
It is not waterproof, but since we basically don't ride in the rain and it is installed in a Cowl, it is probably Large sturdy. I have applied waterproof treatment to the terminal part.
View detail
We are running low on inventory.
This is a necessity when playing with Motorcycle and car electrical components. I recently purchased this Bullet Terminal because the stock of Bullet Terminals was running low when I was reviewing the wiring for my Motorcycle's retrofit electrical components.
I don't like to have to stop working when I run out of materials, so I try to stock up on materials that I use frequently, so when I buy Large quantities, I buy these quantities. In this case, I purchased both Male and Female at the same time.
Some of the No Brand products were inferior, but I can buy Emon products with confidence. This time, too, there were no defective products among the 100 items.
View detail
Good Connector!
This is the best way to get power out of the device, and it is useful in tight spaces. It is also useful in tight spaces and saves you the trouble of attaching Bullet Type Terminals, which are often tied together when wiring is long. View detail
By Location!
When wiring, Wiring Tube is used for the wiring itself, and Coil type Wiring Bando is used for the Bullet Type Terminal and the Jack portion. The Wiring type is easier to use than the Tube type for these joints because it is easier to remove immediately. View detail