Reviews
Fits: HONDA DAX125, HONDA MONKEY125
Is it essential in modern times?
Good product
When you live a life where your phone is indispensable, battery is always a concern.
The USB port gives me a sense of security.
If you read the Instruction Manual carefully, I think it is gentle as a work S-Kill.
However, it is necessary to pay attention to the removal and installation of the light cover (plating parts) and the fit of the wiring.
View detail
It got brighter.
Replaced Headlight Bulb on Z125PRO.
The purpose was not only to make the engine brighter, but also to reduce the load on the battery (power saving). The Z125PRO had LED lights from the beginning, so there was no need to replace the tail lamps. I thought about replacing the blinker light because it has a normal bulb in it, but I decided not to do it because the blinker relay seems to be built into the meter and it would be complicated to change it to LED. This time, I decided to replace the Headlight Bulb and the Position Lamp with LEDs, and for the Headlight, I chose this product, which was the cheapest among the Sphere Light products.
The replacement work was as simple as removing the headlight cowl and replacing the valve with the original one, and since the valve is compact, there were no problems with installation.
As for the feeling of use, the light is bright enough and feels very bright, probably because the light is whiter. I was able to drive safely at night. I was not bothered by the dispersion of the light. Unfortunately, there was not enough of an energy saving effect that I could really feel.
Compared to when we replaced the LEDValve on our ZRX1100 a few years ago, low-cost products are now on the market, and the hurdle for replacement has gone down. If you are concerned about the brightness of your lights, we recommend replacing them with LEDs.
View detail
It was just like the image.
I have just purchased a DDR−S100 with KAMUI3 for the purpose of fixing the Wiring to operate it as a HelmetCamera.
My DDR−S100 was modified to be able to cut the cord in the middle and connect it with Waterproof Coupler after the USB cord was disconnected. The third image shows the Helmet side. By connecting the other side of the cord connected to the Mobile Battery to this side, the cord does not get in the way when attaching and detaching the Helmet.
This time, when I use KAMUI3 for motorcycle commuting, I thought it would be better to have a DriveRecorder, so I decided to install DR−S100 on my helmet, and selected this product as just the right one to fix the Power Cord.
This 3mm TubeHolder was not bad looking and had just the right diameter to move it a bit against the thickness of the Wiring.
I have used 5mm diameter ones in the past, but they can also be cut and used, and I think they are quite user-friendly Parts. However, the adhesive strength is not very strong, so you need to be careful where you apply it. If it comes off, I will reapply with a stronger double-sided tape.
View detail
As expected
I have just purchased a Z125PRO to take out the power supply for DriveRecorderーetc.
D−UNIT has a track record of use in another motorcycle, and we believe it to be reliable. There are several types of D−UNIT, but since the Z125PRO has almost no space under the seat, we chose the D−UNITPlus, which looked a little smaller, considering its fit.
As expected, we had a hard time installing it, considering the position of the DriveRecorder, etc. Finally, we decided to put it on the frame on the Right Side, but it became quite difficult, so we will review it at a later date. As for the Attachment power supply to operate, I pulled out the terminal near the coupler for failure diagnosis and modified it to interrupt the wiring to get it. The wiring to connect to the battery is weak, and it bent easily when I connected it to the battery and screwed it in. I was able to attach it for the time being, but I am thinking of replacing it with a suitable one at a later date. This is a point that we would like the manufacturer to consider improving.
The power supply has one 7.5A Attachment power supply, two 5A Attachment power supplies, and one constant power supply. 7.5A has a Grip heater, 5A has a USB power supply and DriveRecorder, and the constant power supply has a Cycle alarm. As with the D−UNIT, each power supply has a smaller Bullet Type Terminal than the general ones, so the Female side can be inserted by pushing it in with a little force, but the Male side is loose and will fall out if the Female terminal on the electrical component side is not tightened. We hope that the manufacturer will consider improving this issue as well.
Since the battery is small in a small type car, I think it would be better to avoid moving them all at once, but for the time being, each of them can be moved.
I think it is possible to get power supply without necessarily using D−UNIT, by setting up Relay, or by interrupting Attachment power supply from Fuse, etc., but rather than adding Wiring and Relay to Prank and making a mess, I think that by using this However, we believe that by using this method, Wiring can be reflected and a stable power supply can be obtained, rather than adding Wiring and Relay to Prank and making a mess.
View detail
Fits: DUCATI PanigaleV4R, DUCATI PanigaleV2, DUCATI PanigaleV4, DUCATI StreetFighterV2, DUCATI StreetFighterV4
Compatible with DucatiPerformance sequential blinker
This is the parts to change when using DucatiPerformance's Blinker with AELLA's Fender Eliminator Kit.
BlinkerQuantity:Pair (for Left and Right) The long hole for adjustment can be set to the Largeest value, but the image is still used for the License PlateQuantity.:Pair (for Left and Right) The Blinker is just visible from the
View detail
Wow that's cool
I chose this one because I wanted to make it look like an old car.
The OEM Light Bracket could not be removed at all and was eventually disconnected.
View detail
Fits: HONDA MONKEY125, HONDA DAX125, HONDA CT125CT110 HUNTER CUB
I put it on to prevent scratches on the Meter Lens.
[How is it used?
Purchased to prevent scratches before they occur as I am buying a new car.
Was the one you received as per Image?
The product was exactly what I expected.
How was your experience with it?
I think it is effective because it is not hard to see after it is applied and there is a certain amount of heat.
[Points to note]
The meter itself has a slight radius (curved surface), so it is best to apply it with care.
I was very careful, but I let Air hair ・・・・ I crushed the air bite, but it was a little hard to see, so I waited and made a mistake.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
I would like to ask the manufacturer to include a small paper for removing oil and grease, as I know some people do not have one.
View detail
DL1000 V-STROM800 used for power extraction under Seat
The DL1000 V-STROM800 has an OEMOption to install a 12VCigar lighter socket under the Rear Sets. The Attachment power supply Wiring for this purpose comes to the position shown in the photo. If you use KIJIMA's ACC Branch Harness that you purchased, you can get the power supply in Couplet-on. However, please note that the +- terminals are reversed, so the terminals need to be replaced. This is recommended for those who do not want to damage the existing Wiring. View detail
Fits: Others
Orthodox USB port
[How is it used?
no problem
Was the one you received as per Image?
Wiring is also discreet and Refreshingly cohesive.
How was your experience with it?
I was able to charge my phone with no problem.
[Points to note]
I doubt that it will be Waterproof on rainy days.
Other items that would be helpful
Installation Point or hang
:Rare/old cars should be installed by a store you can trust.
View detail
ITType." What does that mean, Italy?
I wanted to change to a Tail lamp with an integrated License Plate Light. I could have chosen anything, but since the car I was installing it on is an old ItalianRacer, I looked for a design that would not ruin the atmosphere and decided on this one.
I think KIJIMA is the best because the valve is sold separately, but it is a product of a well-known manufacturer, inexpensive, and easily available, and KIJIMA also supplies small repair parts such as lenses and rubber base parts. KIJIMA and Tail lamps are strong for classic vehicles.
Personally, I am disappointed only in the Fixing Screw, which is too small, and the Nut and Washer are too small to work with, and the originally drilled holes are too large in diameter. If you are going to drill a hole in a cowl, I don't think M3 or M5 will make any difference.
The base of the Rubber has a fairly solid thickness, and these points are very favorable.
Although there are only three wings, a WiringMemo is included, and it is also designed with the beginner in mind.
View detail
Fits: HONDA CRM50, HONDA CRM80, HONDA TL125, HONDA TLR200, HONDA TLR250, HONDA XLR125, HONDA XLR200, HONDA XLR250, HONDA XLR80, HONDA CRM250, KAWASAKI KSR110, KAWASAKI KSR50, KAWASAKI KSR80, HONDA XR230, HONDA XR250, HONDA XR250 Motard, HONDA XR400 Motard, HONDA NSR50, HONDA NSR80, HONDA XR100 Motard
I think it's good
The installation itself is easy:remove the OEM and install this Light as is. There was no special modification. The glass surface of the Headlight looks like this, [Color] Now that it is Clear, I think it looks pretty cool. The brightness is not as bright as the OEM light lens, but the light distribution is more variable, and with the LED bulbs, it seems to be bright at a single point. View detail
Gamaguchi Clip
The clips are too large for motorcycles and may or may not bite, depending on the type of car. Also, I think it depends on how long the battery lasts. View detail
Repair Parts was a great help!
I broke and obtained the already discontinued Square LCD Speedometer & Tachometer's Gold Genus Reactive Speed Sensor.
I am glad to hear that you are now safely posting speeds.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
Fits: Others
easy to read
Can be installed in the middle of the Handlebar Clamp
It was easy to install
Easy to check voltage, oil temperature, clock, and
I think it's a good product
View detail
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Fits: YAMAHA BWS125 (Bewith), YAMAHA Cygnus X, YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith)
VINO125
The size and shape were the same, but a little cutting work was required, so if you have the tools, you can install it on the VINO125! View detail
exchange
I managed to attach it successfully by replacing only the cover. View detail
It is easy to install.!
OEMHalogen was replaced because it was too dark.
Installation is a simple matter of removing and replacing the OEM. I did a test run during the daytime, and it was a little brighter in the Tunnel. I don't drive much at night, so no problem! I don't drive much at night, so no problem! I don't know about durability, but I'm happy with JAPAN, it's well made and looks good.
View detail