Reviews
CT125 was not supported.
I bought it with the naive hope that it would fit ServiceCoupler, but it did not fit at all.
I used only MarkTube, Bullet Terminal and Wiring and discarded Coupler.
View detail
It is covered with scratches.
Installed to protect the Meter panel.
It is unfortunate that Film is so easily scratched and the line scratches are all over just wiping off the dust.
I would like to see an improvement in the Material to make it less vulnerable.
View detail
USB Power Kit
It was installed on a 2023 MODEL REBEL 500.
There is nothing wrong with the product itself, but it says to just connect the Wiring, but there is actually no electricity flowing to the connected wire, so I asked the Motorcycle shop and found out that I need a Relay to run electricity to this Wiring.
There is a place to install a Relay under the tank, and a dedicated Relay could be installed and used.
Relay is 38501-MKP-DN1 and is Honda OEMParts.
I think there is another way to connect the power supply, but I think it is better to check if Relay is available before purchasing.
View detail
Fits: KAWASAKI Z900RS-Cafe, KAWASAKI Z900RS, KAWASAKI NINJAH2, KAWASAKI NINJAZX-10R, KAWASAKI NINJAZX-10R
I installed it on a Z900RS cafe 2019 and it was always on.
DriveRecorder - purchased for installation.
Installed on a 2019 Z900RS CAFE VINTAGELime green where indicated. (Exterior changed to Tiger color)
The installation itself was easy, but it was a constant power source.
Once the DriveRecorder is installed, the DriveRecorder is activated even when the power is turned off.
I ended up looking for it on the Tester and it originally came with one ACC mounting location.
It was not necessary.
Maybe it can be used in other years.
View detail
Changed from one that draws power from DAYTONA's BrakeLight switch
I had been using a Harness that draws power from DAYTONA's BrakeLight switch, but I replaced it with a Harness that draws power from within the Headlight to refreshing the Handlebar area.
GRAND was taken from the 10mm Bolt under the Horn and the 3-tooth part.
I added a Fuse and installed ETCHarness and USB extraction harness in the Headlight, but it was the Space of Limit. It is troublesome, but when there are many Included Parts:, it might be better to take out the power supply from the Battery under Seat.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000F, SUZUKI GSR750, SUZUKI GSX-R1000, SUZUKI GSX-S750, YAMAHA YZF-R1M, YAMAHA YZF-R1 , YAMAHA YZF-R6
what about
Instruction Manual is not clear and cannot be installed. View detail
Fits: HONDA REBEL500 , HONDA REBEL 250, HONDA REBEL 250, HONDA REBEL 500, HONDA CB650R, HONDA CBR650R, HONDA CB1000R
Note Bullet Type Terminal
Since it is a compliant product, power extraction was very easy.
Note, however, that the Bullet Type Terminal is Female for both Plus minus and minus.
Most of the Bullet Type Terminals for electrical components are Male on the Plus side and Female on the Minus side.
Therefore, it needs to be processed by Electric Works Pliers, etc. to connect.
View detail
Fits: YAMAHA YZF-R3, YAMAHA MT03, SUZUKI Zixxer 250 SF, SUZUKI Gixxer 250, SUZUKI Gixxer 150., SUZUKI GSX250R, YAMAHA SEROW250, YAMAHA YZF-R3A, YAMAHA YZF-R3A, YAMAHA YZF-R3, YAMAHA YZF-R25A, YAMAHA YZF-R25A, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA YZF-R25, YAMAHA XSR900, YAMAHA XSR900, YAMAHA MT-25, YAMAHA MT-25
I don't think I'll have much use for it.
I installed it on my MT-03 2018 and as it turns out, it didn't work for its intended purpose.
I used it to take the USB power supply of the Key switch linkage, but the voltage of the power supply taken out does not become the state of charge even if I connect it with about 9V. attachment power supply, because the voltage may not be stable in the state of the circuit, I gave up the direct power supply and connected it to the circuit which supplies power directly from Battery. So I gave up on direct power supply and connected Relay's Switch as On/Off Switch to the circuit that supplies power directly from Battery, but it doesn't work. I tried various things, but I gave up using the power supply which I take out from this part as a conclusion, and was able to get expected operation by taking out Attachment power supply from another part and connecting it to Switch of Relay.
It is attractive that the power supply can be taken only by interrupting Cabrau, but because the power supply which can be taken out seems not to be stable, I think that it is necessary to choose the use and to use it.
In addition, because the polarity of the power supply taken out is opposite to the color of the Cable in MT-03, and Earth seems to come to the Red wire and Attachment to the Black wire, I recommend that you use it after confirming it with Tester etc. when you use it though there was it in other reviews.
View detail
Initial failure
All Rear SprocketPlus settings could not be done
Perhaps RearLarge Do you think that there is no one to distress?
It can be confirmed only after connecting and there is no guarantee effect
It's my middle finger.
View detail
Is it a decline in quality?
I have also loved it for a long time as a classic staple of OffLoader's classic, but this time the unbreakable lens attached to the New Machine is not broken, the selling Lens did not have a year and all four places were destroyed.
I use Motorcycle less frequently, so it is about 30 hours in real travel time.
As a situation, Lens's Screw part will be lucky with a luck Crack and Lens will drop out.
It has been installed in various Motorcycle for nearly 20 years but never ever happened to this.
Besides, at one location, it is only 4 places to be annihilated, it seems that quality is completely lower than before!
It is desirable to investigate the cause as soon as possible and take countermeasures.
View detail
Bracket's strength is enough
Lens broke in the forest road running on the first day from installation.
Most people seem to be flying Lens,
When I crashed several times at the galley, I cracked normally.
As Bracket never got damaged, Lamp will not stick
I think that the point was good because it was not there.
The mounting position was attached to the OEMLamp and the LeftRear was broken.
For the time being damaged Lens Quantity : 1 Set Buy again.
KLX250 (08-) In case of Watt number difference, it becomes High flasher
We need to think about countermeasures.
View detail
Fits: KAWASAKI KLX250, KAWASAKI NINJA2 Helmet50RR, KAWASAKI D-TRACKER-X
Although the change was considered to the blinker of 400R until now, the smoke is better. I thought that the image can be changed at a low price moreover, and chose. However, the actual one was almost deep-black. It is rather good to attach, although I th
Although the change was considered to the blinker of 400R until now, the smoke is better. I thought that the image can be changed at a low price moreover, and chose. However, the actual one was almost deep-black. It is rather good to attach, although I thought a little more soft color is better. The side winker became unconspicuous on the whole. However, an orange gets conspicuous when the light is switched on. However, since the head of the plus of a stop screw was small, I keenly realized that a suitable tool is required. View detail
it was used by SM570R of the husk Although it is good for Alternating Current to also operate, it has broken in vibration. inside -- components -- the Caracalla word -- measure
it was used by SM570R of the husk Although it is good for Alternating Current to also operate, it has broken in vibration. inside -- components -- the Caracalla word -- measure View detail
Fits: HONDA monkey, HONDA MONKEY RT, HONDA MONKEY R, HONDA MONKEY BAJA, HONDA MONKEY BAJA, HONDA MONKEY, HONDA BENLY50CD90, HONDA BENLY50CD50, HONDA BENLY50S, HONDA DAX, HONDA DAX, HONDA GORILLA, HONDA GORILLA, HONDA Z50R, HONDA CL50
Since the order of only a gear whose mountain of an inner meter drive gear has been lost cannot be performed when an after-attachment circuit run is turned two, a gearbox set is purchased and it has become expenses of 30,000 yen after all. Although it
Since the order of only a gear whose mountain of an inner meter drive gear has been lost cannot be performed when an after-attachment circuit run is turned two, a gearbox set is purchased and it has become expenses of 30,000 yen after all.
Although it is good in the ability only of a meter drive gear to be purchased as an object for repair ...
View detail
The rear blinker of an off-road motorcycle is equipped and they are the comment like one year and a half. It was used and flood started on blinker of one of the two after a while. If it runs for a while in rain, water will accumulate and it will h
The rear blinker of an off-road motorcycle is equipped and they are the comment like one year and a half.
It was used and flood started on blinker of one of the two after a while.
If it runs for a while in rain, water will accumulate and it will have become full of rust even like the middle of a blinker from the mouthpiece of the bulb of the not shorting thing to a base.
It thought that rubber packing was useless, and flood was exhausted when changed into the state where rubber packing was removed.
Although it seems whether it is a problem that the direction which does not carry out packing is not flooded -- The loose connection of wiring may stop happening and switching on the light several times by the blinker of the opposite side again.
It is in the state made to stabilize and turn on by carrying out stuffing and contact being fixed in the good state in the stay which lets wiring pass.
Since it is not divided even if it falls violently, the point is kind, but I think the kana to which I want you to deal with durability to a slight degree.
View detail
It is used equipping the handle guard of an off-road motorcycle, and one year and a half come. It expects and depends, and although it is a design first, although it is the wedge ball which was large, it is thick to some extent. And in the loose c
It is used equipping the handle guard of an off-road motorcycle, and one year and a half come.
It expects and depends, and although it is a design first, although it is the wedge ball which was large, it is thick to some extent.
And in the loose connection of a ball and a base, sticking of the base happened once several times.
The angle of a terminal or a base is adjusted so that it may contact at every time well using tweezers or a slotted screwdriver, but the terminal of a wedge ball will break, shortly after putting in power.
Moreover, if the 12V10W amber color wedge ball for repair is ordered, compared with the bulb which was attached even if it was the same bolt and wattage, a round size is large.
Blink speed becomes quick although it can equip.
Even if it sees a catalogue, this one kind of sale is not made repair of 12V10W.
It is thought that the thing with which the bulb attached to expecting differs in T10, and the object for repair has T13 and different form is used.
Please be careful.
Moreover, a screw rusts immediately.
View detail
SV1000 was equipped. Since it is a form similar to the root of the pure blinker, this LED blinker (ST173) comes exactly. As it is, it is buried in a cowl and I think that it is necessary from the front to carry out the kiln of the spacer etc. sinc
SV1000 was equipped.
Since it is a form similar to the root of the pure blinker, this LED blinker (ST173) comes exactly.
As it is, it is buried in a cowl and I think that it is necessary from the front to carry out the kiln of the spacer etc. since blink cannot be seen at all.
In addition, since the pedestal twisted off and carried out is all a plastic, suddenly, I put in power too much and have broken it (although bitter smile appearance is the highest, it is a fairly regrettable result here.).
View detail