Reviews
Fits: Others , HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUBC125
Attachment, but it is good to have practicality as well!
I bought it to adjust the rear brake, but it is surprisingly conspicuous at one point, and I bought it to match the color of the car body.
Easy to install, practical parts, inexpensive and of good quality, so you can osusume it.
View detail
It is effective in preventing squealing!
I recently replaced the NMAX Brake Pads with Endurance:HGBrake Pads, but now I get squealing from the FBrake when Breaking to the extent that I use it regularly at signal stops.
Since squeak-proof grease can cause Garbage to stick to the surface and burn, I added Brake Pads Shim this time.
Installation is simple, just cut to the appropriate size and affix to the back of the Brake Pads. It is not a hard shim, but a fibrous core material coated with a thin rubber-like material, which certainly seems to suppress squeaking.
*Rubber is, of course, a heat-resistant Material.
As a result of the installation … the squealing has stopped!
BrakeTouch is slightly softer. Personally, I thought the Touch was a little too hard after replacing it with HGBrake Pads. I was thinking that the touch was a little too hard, so it is just right.
I don't mind it when braking during hard sports driving, but I was quite concerned about the squeal when breaking in the normal range for street driving. This product is very effective!
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
Even a beginner could exchange it.
[How is it used?
It has already been installed and so far there have been no problems at all.
Was the installation difficult?
I had no problems if I followed the Instruction Manual. It was very easy to replace the old Cable with the new Cable by tying the old Cable to the new Cable with Tie Wrap and pulling.
It was just hard to get the parts that hold the Wire of the ADDRESSV125 off at all.
How was your experience with it?
Brake is now firmly applied.
[Included Parts:were they on?
None
View detail
Fits: HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA CB50, HONDA CB50, HONDA CB90, HONDA CBX125, HONDA CBX125
For MTX200RII
The rear brake of MTX200RII was extremely ineffective, so I checked it and found that it was the same shoe as the CUB, so I replaced it immediately. View detail
SBS Brake Pads Shim
Used on the Front of GSX-S1000
So far, we have changed the pad, disassembled and cleaned the caliper piston, and changed the rotors.
The squealing was reduced, but it was still squealing.
Since the 2021 model, I know that the OEM has equipped the Pad with ShimPlate.
I used it this time ...
This one works to stop squeaking! It stopped squeaking.
View detail
Fits: HONDA CRF100F, HONDA CRF100F, HONDA CRF70F, HONDA CRF70F, HONDA CRF80F, HONDA CRF80F, HONDA DJ-1, HONDA DJ-1, HONDA DJ-1, HONDA DJ-1, HONDA DJ-1, HONDA DJ-1, HONDA TLM50, HONDA TLM50, HONDA XLR80, HONDA XLR80, HONDA XR100R (for competition), HONDA XR100R (for competition), HONDA XR70R, HONDA XR70R
Exchange from OEM
[How is it used?
The XR100R has front and rear drum brakes, and perhaps because I am used to disc brakes, the brakes do not work very well.
I had a near-miss on a forest road when the rear brake didn't work...so I decided to replace it for safety. When I opened the drum, I found that the OEMShoe was still full, but there was a burn mark on it. I opened the drum and found that the OEMShoe was still full, but there was a burnt mark.
How was your experience with it?
The control of the brake has also been improved and it is easier to handle. I haven't driven on forest roads yet, so I will check it out when it gets warmer.
How did it compare to other products?
I considered other Shoes, but the price was lower, so I went with this one.
[Points to note]
It is quite troublesome to replace the shoes, and it is difficult to install the spring that holds the shoes together. Be careful not to skip the spring by mistake.
Don't forget to clean the inside of the Drum as you remove it.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
nothing special
View detail
just right
The OEM hose clamp could not be used because the hose was replaced at the same time as the caliper was replaced, so this product was installed. The length is just right, and the notch makes it easy to service and fix the hose in place. Now I wonder how durable it will be. View detail
Fits: HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA CB50, HONDA CB50, HONDA CB90, HONDA CBX125, HONDA CBX125
It is inexpensive and Brake works well.
I replaced the front and rear of the LITTLE CUB at the same time. there is a groove on the Brake Shoe, so I think it works better. View detail
Fits: HONDA PCX125 E:HEV, HONDA CROSSCUB110, YAMAHA XG250 TRICKER, YAMAHA TW225, YAMAHA TW200, HONDA FAZE, HONDA FORZA ST, HONDA FORZA T, HONDA FORZA S, HONDA FORZA Z, HONDA FORZA X, HONDA FORZASi, HONDA glom, HONDA SUPER CUBC125, HONDA CBR125R, HONDA CB125R, HONDA FTR223, HONDA CB223S, HONDA CBR250R, HONDA CB250F
For BlackGold Codes
This is one of the Parts that I purchased to make the Grom BlackGold.
It is very easy to install as all you have to do is remove the original CylinderCap and attach this one.
However, I had to be careful not to level the car body firmly when removing it, or it would be a Large disaster.
View detail
MinimotoSize's Caliper
I installed this caliper on my 8inch GORILLA to change the front brake to disc. The wheel installed was old 8inchKITACOWheel, so it interfered with the front brake. Braking power changed drastically. It was a little difficult to bleed air from the brake fluid. View detail
For MONKEY125.
The OEM product was replaced with MORIWAKI's ZeroAnodizedTitaniumium Exhaust, and since the exhaust system is down, the Rear Master Cylinder cap is also in full view. The color of the cap is nice, and it is well made and looks good. The price? The price is good, but the rate of the Point is high. View detail
Fits: SUZUKI swish, SUZUKI ADDRESS110, SUZUKI Address125
No problem at all.
I don't know about durability etc. since I have only used it for about 200 km...
The resistance of the Brake is not too strong nor too weak.
I think that would be just fine for Gen 2...
If you want to be a big fan, this may not be for you.
View detail
I don't have to.
Used for dress-up purposes. The quality is good, but I feel the price is a little high. View detail
Fits: Others , HONDA CROSSCUB110, HONDA SUPER CUBC125, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUBC125
Free Shipping Purpose
Purchased for price matching to get free shipping
It was bigger than I expected and much easier to turn by hand than the OEM. So what? I'm just saying....
View detail
regular product
A classic product, for better or worse.
It seems more durable than regular Hose.
View detail
Race Vehicles
For racing vehicles, the Master Hose may break when replacing the Rear Sets, so this is an item to reduce weight = no Master.
It cannot be recommended for street riding motorcycles. The reason is that slippery components will condense and adhere to the surface of the hose.
I think these parts are for people who can do daily maintenance.
View detail
Fits: HONDA CB223S, HONDA FTR223, HONDA SPACY100, HONDA SPACY125, HONDA SPACY125, HONDA SPACY125, HONDA LEAD 50, HONDA LEAD 100, HONDA LEAD110(EX)
Easy to use
I am using it on a SPACY 100 that I purchased used.
I replaced the NORMALPad that originally came with it with this one because it was getting low.
It works straightforwardly in proportion to grip strength, but my personal preference is that it would be very easy to use if it had a little more initial braking force.
I use it only for city driving, but I think it works normally and stopping normally is a Large thing.
It is durable and a reliable manufacturer.
View detail
Fits: HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA Super Cub 50, HONDA CB50, HONDA CB50, HONDA CB90, HONDA CBX125, HONDA CBX125
to be tested
I am using a honda ape 50. First, the brake pads are a safety issue, so I don't mind using more expensive brake pads, and I have also replaced the original cylinder, every time I need to brake when driving It needs a lot of preparation in advance, although the brake pads are installed, but I have not had time to test the effect View detail
Looks Custom
Looks Custom
For MONKEY125 riders.
I don't think they're going to notice …
It's made by KITACO.
KITACO's Down fender has
It's a strange product that can't be installed lol.
The Down fender is made by OVER.
I was able to install it.
View detail
Fits: KAWASAKI EPSILON150, SUZUKI G, SUZUKI G LIMITED 05-08 (Model:CF46A FNO. CF46A-100001-) for Front, SUZUKI G LIMITED 09 (Model:CF4EA Frame NO:CF4EA-100047-) for Front, SUZUKI ZZ, SUZUKI ZZ, SUZUKI ADDRESS110, SUZUKI ADDRESS110, SUZUKI Address50, SUZUKI ADDRESS V100, SUZUKI ADDRESS V100, SUZUKI ADDRESS V100, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125S, SUZUKI ADDRESS V50(2Cycle), SUZUKI AVENIS125, SUZUKI AVENIS150
KITAKO Brake Pad Cost and feel of the pad is important.
[How is it used? I commute 80% of the time.
Was the one you received as per Image? I've been using the same one for a while now.
Was the installation difficult? If you are used to replacing the pad, it will be a piece of cake. If you're new to this, work carefully!
How was your experience with it? The durability and Cost Balance is good, and it works and stops properly, so no problem!
[Included Parts:were they on? Pad is only 1 Caliper-min
[Was there anything that disappointed you? None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
This time, I prepared a new pad to replace the brake hose with stainless mesh one. The brake fluid will also be replaced, so it's also to get the right amount of fluid. I also put a thin layer of grease on the back plate to stop the squeal, and shaved the edge of the pad for chamfering. I also shave the edge of pad for chamfering. It's good to check what you need for replacement work and prepare for it.
View detail