Reviews
Volume control
[How is it used?
The volume of the external exhaust system that came with the used car when I bought it was too loud,
After Fire was also available at the same time, so it was purchased for exhaust adjustment purposes.
Was the one you received as per Image?
The size error was very small, and it was possible to mount the unit on a pontoon.
However, in our case, it will be installed in the exhaust pipe side of the exhaust system,
Drilling + Rivet fixation.
Was the installation difficult?
In the case of our vehicle, the exhaust system was inserted into the exhaust pipe,
The fact that we could not bolt on was something we could have anticipated,
Also, I had all the necessary tools on hand for processing,
It wasn't a difficult task.
We have an O2 sensor attached to the exhaust pipe on our vehicle,
It was also necessary to machine the contact points with a hole saw.
How was your experience with it?
I was able to reduce the volume from the original explosions,
For starting up (when cold), the volume is still too loud to be noticed in residential areas,
Once the Engine is started, it is ready to go.
[Included Parts:were they on?
Quantity:I bought 2pcs, but one of them had a bolt nut that came off,
It was playing in the bag.
However, it is not visible once it is installed,
I'm not talking about the scratches.
[Was there anything that disappointed you?
none in particular
Other items that would be helpful
At the very least, measure the inside diameter of the piping at the planned installation location before purchasing.
For those who intend to install the product by themselves, some manufacturing errors should also be taken into account,
It is advisable to have some processing tools and liquid gas available.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS SE
Installation of groundwork
Purchased for Point cover installation.
Since all you have to do is remove and attach it, I think anyone can do it easily.
Only 1 pc of Screw lock agent will be attached, so preparation is necessary.
View detail
On the MVX250F.
I used it to fill the front fork with air. It's good because I can fill low pressure like 0.4 properly. View detail
Fits: HONDA DAX125, HONDA MONKEY125
Is it essential in modern times?
Good product
When you live a life where your phone is indispensable, battery is always a concern.
The USB port gives me a sense of security.
If you read the Instruction Manual carefully, I think it is gentle as a work S-Kill.
However, it is necessary to pay attention to the removal and installation of the light cover (plating parts) and the fit of the wiring.
View detail
Used for Radar installation
It is necessary to remove the Mirror until the Meter is removed.
I thought it would be easy, but it was more complicated than I thought.
View detail
Moped Plate
It is easy to install.I just installed it,
How durable is the Sticker?
View detail
DL1000 V-STROM800 used for power extraction under Seat
The DL1000 V-STROM800 has an OEMOption to install a 12VCigar lighter socket under the Rear Sets. The Attachment power supply Wiring for this purpose comes to the position shown in the photo. If you use KIJIMA's ACC Branch Harness that you purchased, you can get the power supply in Couplet-on. However, please note that the +- terminals are reversed, so the terminals need to be replaced. This is recommended for those who do not want to damage the existing Wiring. View detail
It is easy to install.!!
Anyone can easily install it.
I am satisfied with the shape as expected.
The color would have been much better if it had been matte….
It's looking good.
View detail
ITType." What does that mean, Italy?
I wanted to change to a Tail lamp with an integrated License Plate Light. I could have chosen anything, but since the car I was installing it on is an old ItalianRacer, I looked for a design that would not ruin the atmosphere and decided on this one.
I think KIJIMA is the best because the valve is sold separately, but it is a product of a well-known manufacturer, inexpensive, and easily available, and KIJIMA also supplies small repair parts such as lenses and rubber base parts. KIJIMA and Tail lamps are strong for classic vehicles.
Personally, I am disappointed only in the Fixing Screw, which is too small, and the Nut and Washer are too small to work with, and the originally drilled holes are too large in diameter. If you are going to drill a hole in a cowl, I don't think M3 or M5 will make any difference.
The base of the Rubber has a fairly solid thickness, and these points are very favorable.
Although there are only three wings, a WiringMemo is included, and it is also designed with the beginner in mind.
View detail
Fits: HONDA REBEL500, HONDA REBEL250SEdition, HONDA REBEL250
KIJIMAFrontReachSeat
I used to ride with a GelCushion, but it used to be a hassle with gapping, etc. The Cushion is no longer necessary, and the seating has become more comfortable.
Regarding the installation, there is too much play in the claws that insert into the body, so some modification is necessary, such as covering the claws with rubber material. I would like you to improve this part.
View detail
Required for OH above the waist
Used for Valve matching. This is a task that is rarely done, so I am thankful for this Size. (Even this Size will probably never run out.) View detail
GOOD GOOD Glass Wool Acoustafil
Cutting is accurate and no cutetc. is required.
The Glass fibers are braided and compressed thinly, so there is virtually no scuffing of the Glass fibers.
(but protective equipment is still required)
The compressed Seat is temporarily fixed with Tape and expands with heat after assembly.
The work of putting it in the tube is easy.
The purchase cost is usually a problem instead of the difficulty of the work being reduced compared to Glass Wool.
Silencer parts removal & disassembly, Rivet removal by Drill,
Rivet re-fixing, hole alignment, and removal of remaining gasketetc. using special tools,
Parts matching checks and other su-kills are necessary.
One 1100mm-long Seat is equivalent to one Silencer.
Two Silencers would require two pairs.
View detail
Fits: HARLEY-DAVIDSON SPORTSTER Family, HARLEY-DAVIDSON DYNA Family, HARLEY-DAVIDSON DYNA Family
Used for GSX250E
I bought it knowing that it does not fit. The inner diameter is 39Φ and the inner diameter of my car is 33Φ so naturally it is loose, but since it does not fit the outer diameter due to the Stubby installation, I dared to fix it loosely so that it can move freely up and down. The Inner is short and not traveled a lot, so it works well as a protector to protect from stepping stones on the Dirt. View detail
Lightweight bar ends from KIJIMA
Lightweight bar ends from KIJIMA, ideal to save some weight while still maintaining some vibration damping efects. Can be use on both the stock steel handlebars or aftermarket aluminium ones, as it cames with both adapters type and the Allen tool also. Overall a good quality/price product. View detail
It became a little Fashion.
The purpose of the parts is to make the Indicator Lamp easier to see. Of course it has that effect, but I think there is a little change in aerodynamics.
I feel strong wind pressure when I reach about 100 km/h at high speed. After installing this Visor, I felt it was reduced a little.
I recommend it to anyone who wants to do a little something better.
View detail
Fits: HARLEY-DAVIDSON Dyna Convertible FXDS-CONV, HARLEY-DAVIDSON Dyna Low Rider EFI FXDL, HARLEY-DAVIDSON Dyna Low Rider FXDL, HARLEY-DAVIDSON Dyna Street Bob FXDB, HARLEY-DAVIDSON Dyna Super Glide Custom EFI FXDCI, HARLEY-DAVIDSON Dyna Super Glide Custom FXDC, HARLEY-DAVIDSON Dyna Super Glide EFI FXDI, HARLEY-DAVIDSON Dyna Super Glide FXD, HARLEY-DAVIDSON Dyna Super Glide FXD35, HARLEY-DAVIDSON Dyna Super Glide Sport EFI FXDXI, HARLEY-DAVIDSON Dyna Super Glide Sport FXDX, HARLEY-DAVIDSON Dyna Super Glide T-Sport FXDXT, HARLEY-DAVIDSON Dyna Switchback FLD, HARLEY-DAVIDSON FXR 2, HARLEY-DAVIDSON FXR 3, HARLEY-DAVIDSON FXR 4, HARLEY-DAVIDSON Softail 15th Anniversary Fat Boy FLSTF, HARLEY-DAVIDSON Softail Cross Bones FLSTSB, HARLEY-DAVIDSON Softail Custom EFI FXSTC, HARLEY-DAVIDSON Softail Fat Boy EFI FLSTFI
Parenthesis is good.
It is easy to install and looks great Parenthesis. View detail
Fits: SUZUKI GSX-S125, SUZUKI GIXXER 250, SUZUKI GIXXER SF250, SUZUKI GSX-R125, SUZUKI GIXXER 150, SUZUKI V-Strom250 SX
Extension Harness Min.
Quantity of 1 Set for 1 Vehicle to install TRL2Blinker:Set.
TRL2 LED Blinker*4
Mount for TRL2*4
Extension Harness (long)*2
Extension Harness (short)*2
MicroIC Blinker Relay*1
Small and very Stylish
The mounting is done by sandwiching the Mount with the Plate, and since the hole is small, the Bullet Type Terminal is inserted while shifting it slightly.
The price is almost the same if you buy them individually, but you save money for the Extension Harness.
The included MicroIC Blinker Relay is about the size of a small finger, so you should have no trouble finding a place to place it, but the terminals are bare, so be careful not to touch the Gold Genus.
View detail
In OEMHelmet holder
I have not been able to install it yet because the weather has been rainy on my vacation since I purchased it, but as far as I have checked Reviewetc., I think it is a highly satisfactory product.
Since the OEMHolder cannot reach the Helmet's Holder...
View detail
Fits: Others , HONDA 400X, HONDA ADV150, HONDA CB1000, HONDA CB1000, HONDA CB1000SF, HONDA CB1100, HONDA CB1100, HONDA CB1100CA, HONDA CB1100NA, HONDA CB1100SF, HONDA CB1100SF, HONDA CB1300SUPERFOUR, HONDA CB250F, HONDA CB250R, HONDA CB250R, HONDA CB300F, HONDA CB300F, HONDA CB300F, HONDA CB300R
Number Protection
I installed it to prevent the Number from bending. So far, it works well because it does not bend when it hits.
Also, it's very heavy.
View detail
A4 Size is good.
Size is A4, so it is easy to handle.
The fact that it is not in a volume is good because it can be handled without Habit being attached.
View detail