Reviews
It is useful for attaching and detaching the helmet!
[How is it used?
ARAI's Helmet is a type of helmet that is fixed by putting the chinstrap through the D Ring, so it takes time to put it on and take it off one time at a time.
KITACO and DAMMTRAX's could not accommodate the width of ARAI's chinstrap, so the only option was KIJIMA.
Was the one you received as per Image?
I thought the Black part was Plastic, but Material:It was Rubber. I think the texture is not bad, even if Steel is unavoidable.
Was the installation difficult?
If you do not bend the bracket between the belt and the chinstrap, the plastic part of the chinstrap will get caught and will not go through. It requires some ingenuity. I used other people's installation as a reference.
How was your experience with it?
If it is so convenient, I wish I had used it earlier. Some people say that the excess string becomes like a whip when cruising at high speeds, but if you fix it with the original plastic part, it will fit with no problem at all.
[Included Parts:were they on?
None in particular, and no Instruction Manual is available, which is unfriendly.
[Was there anything that disappointed you?
Nothing in particular,
I think it will eventually rust because the material is steel, but if it were made of stainless steel, there would be nothing to say.
▼Material even if a little expensive:I would really like you to make a Stainless Steel product. In that case, it may be difficult to process Bracket, but ….
View detail
I have been using it for many years on my Helmet for street riding.
I use it on my ARAI full face helmet for street riding, and it is convenient for me because I can attach and detach the helmet's chinstring with one-touch, but I have to remove the Snap button on the chinstrap belt, However, the Snap button on the chinstrap belt has to be removed, so it is a bit tricky to install. The Gold Parts are made of steel, so rusting is a bit of a problem.:I would be happy with Large change if they commercialize it in Stainless Steel (even if the price is higher, I would still buy it...). I would be happy to buy it if it was made in Stainless Steel. View detail
Required processing
The one-touch made it easy to attach and detach the Belt, but the part where the Belt passes through is too narrow and the Button attached to the Belt does not pass through. View detail
One-touch with this
I replaced the chinstrap on my helmet with a one-touch. The other day I went on a long touring trip and noticed that I was not wearing a chinstrap and managed to tie it through the ring with my left hand, but I was reminded that it was dangerous to use a large clip while riding and I remembered that KIJIMA has a one-touch clip and ordered one. I thought about it, and this was the third time I had ordered one. When I looked at the delivered product, I saw that it was exactly the same as before. The installation is easy for anyone. As for the quality, I think it would be easier to install if the claw that locks the clip by pushing it in was longer and could be adjusted in about three steps. View detail
The string is easy to pull out.
I am afraid to attach the strings later by Sliding them without sewing them, but they can fall out.
A soft type of string may slip through the gap and lead to an unexpected accident.
I ended up sewing it up and using it so that there was no Gap.
View detail
That's too bad
For one thing, I was surprised and a bit troubled that the Instruction Manual was nowhere to be found.
One, I made the mistake of buying it without looking closely at the impressions.
I did it as I saw fit, but alas, I did not use it.
I tried to install it on an ARAI RX-7X, but when I put the string through the bracket on the Male side and folded it back, the Button hit it and did not go through.
I also tried with SHOEI's J-Force ? (25mm string), but the Male side also did not go through because the Button was in the way.
View detail
One-touchSpec. will be w
Clip to make the chinstrap One-touchSpec.!
It took some effort to install, but with the One-touch chinstrap attachment, I'm happy!
View detail
Helmet One-Touch Clip
I installed it on ARAIHelmet.
The belt width of ARAI is 25mm, so I chose L Size. I'm satisfied with it because I can remove it with One-touch, but it's hard to use it with Glove on.
View detail
Saved me wasting money on a new helmet
My wife's crash helmet isn't used much and a few weeks ago the male part of the helmet strap was lost on the road. I saw this Kijima helmet buckle and bought it because it seemed cheap. Fitting was very easy, no sewing or cutting required. The hardest part was removing the old helmet clasp. My wife finds it easy to fasten and adjust using the strap and equally simple to remove. View detail
It's going to be lumpier than I expected.
important item
[Was there anything that disappointed you? Large texture than the body was expected.
Do you have any wishes or improvements you would like to make for the Manufacturer? I would like to get a more compact size.
[Do you have any products to compare it to? No
Frequently Asked Items
What made you decide to buy? Brand
How was your experience with it? There's a little bit of discomfort on my chin until I get used to it.
Was the installation difficult? No
【Please tell me the installation point and hang】 Squeeze the Helmet tightly to prevent the Belt from loosening
[Was the Instruction Manual easy to understand? Yes
View detail
subtle…
Buy Jet helmet. DRingSpec. Because I bought it from the troublesome.
Because it is Universal, Spec. That's it.
It was originally a tight helmet so I could not get it first in normal driving.
I think that it is useful if there is.
Those who place importance on practical use may be tough.
View detail
Not available.
After attaching to Arai's ASTRO-IQ, the gold tool hit Moro at Nodobotke, it gave me a lot of pain, so I gave up using it.
Even in a light fall accident, I think that I will do Nodobotoke if a force is applied from the front.
This can not be used.
View detail
It is reliable to be moved by the structure which main structure parts carried out firmly by metal. Therefore, it matches on the Jet type Helmet of black rough [ for American motorcycles ] well. Satisfactory also in price. however, it is the very meta
It is reliable to be moved by the structure which main structure parts carried out firmly by metal.
Therefore, it matches on the Jet type Helmet of
black rough [ for American motorcycles ] well.
Satisfactory also in price.
however, it is the very metal -- originating -- it is felt a little heavy.
Moreover, I thought that it would be better if an outline dimension is brief to a slight degree on the whole.
A demerit mark was given to one * at this point.
However, I think that good shopping was carried out as comprehensive evaluation.
View detail
It is nostalgic. It used also 25 years before . Since it is convenient, it uses recently, buying it again. Since it is somewhat heavy and some painful times have a jaw, it is -one point. Since a stronger One-touch clip than this is not k
It is nostalgic.
It used also 25 years before
.
Since it is convenient, it uses recently, buying it again.
Since it is somewhat heavy and some painful times have a jaw, it is -one point.
Since a stronger One-touch clip than this is not known for the moment by
, I think that this is good.
View detail
Yamaha It attached to YJ-5. The Snap button removed and attached. most worrisome, metal fittings are equivalent to the Adam's apple -- you must just be going to adjust looseness a few. Since the Size of a Helmet is S, it may be that it is too many worr
Yamaha It attached to YJ-5. The Snap button removed and attached. most worrisome, metal fittings are equivalent to the Adam's apple -- you must just be going to adjust looseness a few. Since the Size of a Helmet is S, it may be that it is too many worrisome. I would like to try for a while and to judge. View detail
Since desorption was troublesome at the Belt type, the jaw string of an ARAI's Full face currently used attached this One-touch clip. Although surely it could remove easily and became convenient single hand, since the feel when it inserts in is blun
Since desorption was troublesome at the Belt type, the jaw string of an ARAI's Full face currently used attached this One-touch clip.
Although surely it could remove easily and became convenient single hand, since the feel when it inserts in is blunt, they are uneasy goods which remain a few.
An after [
] metal part rusts easily for a while.
View detail
The Items which enables it to desorb simply the Helmet which adopts D ring system by a Buckle. Since it is overflowing on the Net, is anyone of how to attach problematic? As comment, it is the place that it is so so. It is charm tha
The Items which enables it to desorb simply the Helmet which adopts D ring system by a Buckle.
Since it is overflowing on the Net, is anyone of how to attach problematic?
As
comment, it is the place that it is so so.
It is charm that can cancel Locke of a Helmet easily.
Compared with what is equipped standardly with AVAND of OGK, etc., a function is inferior in
.
Although it turns out that it was acted as Locke of that of
AVAND at the feel made into the Snap, the direction of an One-touch has almost no response.
The former receives that it is with a Center Button, the latter is contrary to appearance, and
Locke's release method is also a SIDE.
Since it is
metal fittings, it is also a subtracting point that there is some weightiness.
This point is whether since it is the durability of goods, and a trade-off, it is unavoidable.
Let's be ready for it and purchase that it is a
general-purpose article.
View detail
[Webike Monitor] It attached to the ARAI's Classic SW. Although others are also said, there is no description. Since the Button (?) which an ARAI inserts in a jaw string's end with パチン of prevention with butter was attached, the string did not pass
[Webike Monitor] It attached to the
ARAI's Classic SW.
Although others are also said, there is no description.
Since the Button (?) which an ARAI inserts in a jaw string's end with パチン of prevention with butter was attached, the string did not pass easily, but on the Plierses, opened metal parts once and let them pass.
The
using feeling feels it as the somewhat large kana ?.
I think that considering a price and convenience they are good goods.
View detail
Z-6 on hand and HORNET-DS are equipped. Since desorption is easy compared with a D ring, convenience is convenient. About safety, it will fall more certainly pure. since it has not separated during use, so that it regards as questionabl
Z-6 on hand and HORNET-DS are equipped.
Since desorption is easy compared with a
D ring, convenience is convenient.
About
safety, it will fall more certainly pure.
since it has not separated during
use, so that it regards as questionable -- でも --
-- I think that there is nothing.
(Wishiful thinking) ?
attachment removed the Snap button for both of the Helmets whether it can be used in the
Circuit.
It does not use at any rate.
If
Buckle portion is bent, it will enter, but it is safer not to do
What drops intensity specially.
= yield point bent once [
] is exceeded -- therefore -- appearance -- even when it is OK, there is a danger electrical of doing
fracture of.
Probably, he should understand that there is a
Risk.
Locke will stop, if it puts exactly, but since the click feeling is thin, after
Locke's carrying out, it is checking pulling once and not escaping.
It has already grown into a habit.
If it forgets to act as Locke carelessly and begins to
Run as a Demerit which the direction besides
is not writing, it will be flapped by the wind and will be in charge of the exterior of a Helmet with a clang.
-- when the first, what sound it is -- with no getting [ impatient ]-?? mistake.
(Smile)
The Buckle instigated in the style of once moreover hits the Adam's apple directly, and it is
うぎょあぐえぇぇぇぇえぇぇぇ during a run (;_; It has become.
(Smile) )
Let's run after stopping a Buckle exactly.
(Bitter smile)
View detail
It used for the ARAI's SZ. It is satisfactorily easy, and attachment also has intensity rather than the One-touch clip made of resin by metal metal fittings, and is safe. Although the Center shifted at the time of a plug and the Clip of such st
It used for the ARAI's SZ.
It is satisfactorily easy, and
attachment also has intensity rather than the One-touch clip made of resin by metal metal fittings, and is safe.
Although the Center shifted at the time of a plug and the Clip of such structure also had the thing of being hard to equip, desorption of that made from this KIJIMA was completed in general satisfactorily.
I think that it is useful for crack prevention when a Rubber also places a Helmet in the circumference of
metal parts.
Although after
is perfect if what does not rust this metal construction material easily is adopted
View detail