Reviews
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS SE
Installation of groundwork
Purchased for Point cover installation.
Since all you have to do is remove and attach it, I think anyone can do it easily.
Only 1 pc of Screw lock agent will be attached, so preparation is necessary.
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1200R, BMW R1200RS, BMW R1200RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1250R, BMW R1250RS, BMW R1250RT
It's a must for Oil replacement.
BMW is said to be a Motorcycle only for the rich, but I still want to put in my favorite Oil and keep the cost down.
The only thing I decided to ask Dealer for was the price, and the price is meta-fucking-high.
So I changed the Oil by myself!
Attachment, too!
This is essential in that case!
View detail
Fits: YAMAHA XSR900, YAMAHA YZF-R1M, HONDA NC750X, HONDA NM4-01, HONDA NC700S, HONDA NC700X, HONDA NC750X, HONDA NC750X, HONDA NC700X, HONDA NC700X, HONDA FAZE Type S, HONDA FAZE Type S, HONDA FAZE Type S, HONDA FAZE Type S, HONDA FAZE Type S, HONDA CTX700, HONDA CTX700, HONDA FAZE, HONDA FAZE, HONDA FAZE
For THRUXTONRS
OEM replacement for Triumph is not available, but if the OD and internal Screws match.
Can be installed. Always change Oil and Drain plug Magnet
This product gives me peace of mind when I look at it and worry about all the iron dust.
Overall length is slightly longer than tiger OEM, but no problem for installation.
View detail
Fits: SUZUKI GIXXERSF 250, SUZUKI GIXXER 250, SUZUKI GIXXER150, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI BURGMAN 400
You should change the cheap ones often.
This is a reasonably priced Filter for a 2012 KTM DUKE200. If you are a normal rider, it is better to change the cheap one frequently than to buy an expensive Filter and use it persistently.ОRing should be changed once in a while, and at that time you should use Quantity:Buy Set's stuff!
Motorcycles that have been run a lot do not have gold dust, so it is enough without magnet.
The replacement procedure assumes that the Oil is drained.
Remove the lid of ?Filter. 8mmWrench
?This time we will use the lid side and the back ОRing.
Remove the filter and tighten the Bolt on the lid to finish. After replacing the filter, run it for a while to check for leaks.
By the way, the cheap ones seem to have large filter holes. The cheap ones may have oil leaking out from the gap, not into the filter but into the inside of the filter.
View detail
Fits: HONDA GB350, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side
Cheaper than OEM
This will be no problem, unless you need OEM! You can spend the difference on Oil. View detail
Fits: HONDA Forza(MF10), HONDA Forza(MF10), HONDA glom, KAWASAKI ZX-9R, KAWASAKI ZX-RBF, KAWASAKI ZX-RAFA, KAWASAKI ZX-25R SE, KAWASAKI ZX-25R, KAWASAKI ZX-14R, KAWASAKI Z125 Pro, YAMAHA YZF-R25, YAMAHA YZF-R3, KAWASAKI W650, HONDA NC700X, HONDA NC700S, YAMAHA MT-25, YAMAHA MT-03 (2015-), HONDA CRF1000L Africa Twin, HONDA CBR400R (2013-), HONDA CBR250RR(2017-)
Affordable and easy to use
[How is it used?
Wiring was needed for Circuit Running.
Was the installation difficult?
Copper Washer is included, so there is no need to buy it separately for the first time.
Of course, without the WiringPlate, wiring is not possible, so please purchase and install it separately.
6R is Oil Pan Bolt with Plate bite.
I was reluctant to remove the oil pan bolt, but so far there has been no oil seepage, so I can use it without any problem.
How was your experience with it?
Designability is not particular, but I have no problem with the functionality.
Affordable and easy to use.
[Included Parts:were they on?
Copper Washer and Wire included.
It is a one-time fee and must be purchased the next time it is used.
Point and hang of installation
Wiring should be done by applying tension in the direction that the bolt is tightened. Sometimes we see wiring that is not only meaningless but also dangerous.
View detail
Fits: HONDA GB350, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side, HONDA Side by Side
Less expensive than OEM
It is less expensive than OEM. Performance is probably comparable to OEM. View detail
Fits: KAWASAKI Z400LTD, KAWASAKI NINJA600R C1-10, KAWASAKI Z750GP, KAWASAKI Z1000R, KAWASAKI EN400, KAWASAKI 1000GTR, KAWASAKI Eliminator 400, KAWASAKI ZEPHYR550, KAWASAKI ZEPHYR750, KAWASAKI Z400 Custom G3 (83), KAWASAKI ZL1000 A1(87), KAWASAKI VOYAGERV II X II B 86-99, KAWASAKI VOYAGERV II X II A 86-99, KAWASAKI VOYAGERV II B 86-99, KAWASAKI VOYAGERV II A 86-99, KAWASAKI ZEPHYR750 RS, KAWASAKI ZZR1200, KAWASAKI ELIMINATOR 750, KAWASAKI ELIMINATOR 900, KAWASAKI ZEPHYR1100 RS
I have no particular problem using it.
It is a consumable item that is used for a short period of time, so it is very helpful to be able to purchase it at a reasonable price. I have no problem using it. View detail
Good
If you read the manual, it is easy to install and fits well. It weighs more than you think. The cooling fins have a nice shape. View detail
KIJIMA
Was the one you received as per Image?
Yes
Was the installation difficult?
Really easy!
How was your experience with it?
Great!
[Was there anything that disappointed you?
There wasn't one.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Oil Filter for Grom KITACO's Clutch cover
Recommendation for those who use Grom KITACO's Clutch cover.
I replace Filter every two times, but I buy in bulk because it's a consumable item.
View detail
To bleed air from the Brake
Originally a Catch tank, it is used as a waste receptacle when bleed air is removed from the Brake.
I used to drill holes in the lids of plastic bottles, but it was inconvenient because the lids would break or slip off.
This product has a large hole that engages securely with the tube, so the tube does not move.
The One-Way Valve, which costs about 800 yen, makes air venting easy.
A dedicated air venting kit costs about 5,000 yen, but if you buy this product and Valve, it costs about 1,500 yen.
The capacity is sufficient for Motorcycle and it is not bulky.
View detail
Fits: KAWASAKI NINJA600R C1-10, KAWASAKI Z750GP, KAWASAKI Z1000R, KAWASAKI 1000GTR, KAWASAKI EN400, KAWASAKI Eliminator 400, KAWASAKI Z750FXII/III, KAWASAKI Z750FXII/III, KAWASAKI Z400LTD, HONDA GL1200 Gold Wing, HONDA CBX1000, HONDA CB900F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F
Purchased for CB750four
I expect Magnet effect because I have had iron powder mixed in before. View detail
Fits: KAWASAKI NINJA600R C1-10, KAWASAKI Z750GP, KAWASAKI Z1000R, KAWASAKI 1000GTR, KAWASAKI EN400, KAWASAKI Eliminator 400, KAWASAKI Z750FXII/III, KAWASAKI Z750FXII/III, KAWASAKI Z400LTD, HONDA GL1200 Gold Wing, HONDA CBX1000, HONDA CB900F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F, HONDA CB750F
Magnetized, higher than OEM
I always use OEM, but this time I switched to KIJIMA's Magnet. We will see how it goes. View detail
Fits: HONDA XR400R, HONDA GB500, HONDA FMX650, HONDA XR650, HONDA GB400, HONDA CBX250RS, HONDA CBX250RS, HONDA GB400, HONDA GB400, HONDA GB400, KAWASAKI KX450F, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN, HONDA GB250 CLUBMAN
Thank goodness it's readily available.
I used KIJIMA oil for replacing the oil in my KLX230R. I bought KIJIMA oil because it takes a long time to deliver OEM products and they are often more expensive than the Replacements. I was able to replace the oil without any problems. View detail
Fits: SUZUKI GIXXERSF 250, SUZUKI GIXXER 250, SUZUKI GIXXER150, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI BURGMAN 400
For Burgman 400
Pros: Efficient Filtration: The Kijima oil filter effectively filters contaminants, ensuring optimal engine performance. Durable Construction: The build quality of the filter is commendable, demonstrating resilience against pressure and temperature variations. Easy Installation: Installing the Kijima oil filter is hassle-free, making it convenient for DIY enthusiasts. Reasonable Price: Considering its performance and longevity, the filter provides excellent value for money. Cons: Limited Availability: Depending on your location, finding Kijima oil filters might be challenging compared to more widely available brands. Lack of Advanced Features: Some competitors offer additional features, such as anti-drainback valves or textured grips, which must be included in the Kijima filter. View detail
Installed on GSX1100S KATANA
I bought it because of its simple shape and size. There is no drain outlet, but this is not a problem because it needs to be removed to discharge. View detail
Fits: YAMAHA Majesty., YAMAHA tricker, YAMAHA tricker, YAMAHA tricker, YAMAHA tricker, YAMAHA Cerro 250, YAMAHA Cerro 250, YAMAHA Cerro 250, YAMAHA Cerro 250, YAMAHA XT250X, YAMAHA XT250X, YAMAHA WR250X, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250R, YAMAHA WR250F, YAMAHA WR250F
Usable normally with no problems.
Element is exchanged every two times when changing Oil
I have used various manufacturers' products to get points or to get them at a discount, but this KIJIMA product is just as good as the others and works just fine.
View detail
Fits: YAMAHA SR500, YAMAHA SR400, YAMAHA SR500, YAMAHA SR400
It works for Powerful utilization!
Powerful, if replaced with Power Filter, Quantity:Set is the Breather filter that I bought this time.
What is a Breather filter?
This filter is a mechanism to release the air inside the engine that expands due to heat and the engine oil that evaporates slightly, so as not to release this vaporized oil into the large volume of air or contaminate the motorcycle. 。
In NORMAL, the air cleaner box has this role as well. 。
If you don't care about environmental issues, you can replace the Breather Hose with a longer one and extend it behind the Frame 。 There is also a Breather box that cools the vaporized oil and returns it to a liquid state. 。 Why do we need Breather…… because it is loaded with Engine.
Gasoline is burned in the engine, but at that time, it cannot be completely combusted and unburned gas is generated.
This unburned gas enters the crankcase between the piston and cylinder. The Breather is responsible for returning the blowby gas to the Air Filter.
So, it seems like it would be a good idea to release the blowby gas (after successfully separating it from the oil) into the atmosphere, but ……blowby gas contains carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxide (NOX). Therefore, if they are released as they are, they will have a negative impact on people and the earth. As a side note, the law currently prohibits engines from emitting large volumes of blowby gas.
Merit to put on Breather filter?
(1) Blowby gas contains unburned gas generated inside the engine and impurities such as Carbonetc. in the oil. 。 The Blowby gasFilter separates gas and oil, returns the oil to the oil pan, and removes impurities to prevent contamination from entering the intake tract.
(2) Prevents Garbage, etc. from entering Crankcase.
(3) The performance effect is that the pressure generated inside the crank is released to the outside, and by reducing the rotational resistance of the crank, the engine revs up smoother and the response improves, and the body handling by the Axel is improved.
There is no Demerit.
good point
◎Engine braking is eased and jitteriness during deceleration is alleviated.
◎Response of deceleration→re-acceleration is faster.
◎The fact that you don't have to worry about what others see around you.
A bad point
◎Because it absorbs Gas, it gets dirty quickly and needs to be cleaned frequently.
◎Because of the structure, there is a smell of Gas around the car body compared to when using the NORMALAir Filter because it is external.
If possible, it is recommended that the breather filter be fixed near the carburetor inlet for the treatment of blowby gas.
Unlike the NormalAir Filter, the Blowby reduction is eliminated and the air intake efficiency in the air cleaner box is improved, so there is some demerit work, but I think the effect can be felt.
If you set the filter to "Powerful", be sure to add a "Breather filter" as well!
View detail
Nice little piece
This line cover is nicely manufactured. It does not include a gasket. I was able to re use my original just fine. I don't think this does anything for the cooling but it looks cool. I like the air cooled look. View detail