Reviews
This is a standard component that seals the Well and Pipe together.
[How is it used?
Black dirt was dripping under the joint between the Chamber and Silencer, so I checked the packing and found a small amount of exhaust oil leaking out. 。 Packing was replaced about 6 years ago when the Chamber was cracked and replaced, so the surface was also cracked and had reached the end of its life span! 。 Still, it is amazing that there have been no problems for six years.
How was your experience with it?
I have been using it as a standard for some time and it is Just fit.
How did it compare to other products?
It is the one and only component that cannot be compared.
[Points to note]
Although Large is strong even when used in its original state, experience has shown that there are two key points to increase durability.
(1) Do not throw away the old part Clamp you removed, but use it (1 piece) 。 The new part has two Clamps at the front and rear ends of the packing, but by adding the Clamps from the old part to the center section, three Clamps can be used to secure the packing more securely and stably for a longer period of time.
2) Apply heat-resistant SiliconSealer to the joint of the Pipe (the part where it plugs in) and the entire inside of the Packing, and assemble. (If you are concerned about the appearance, wipe off any protrusion.)
Other items that would be helpful
Items to buy together:Silicon-based oil-resistantGasket Ultra CopperRTVSilicone
View detail
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily.
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily. View detail
Valuable Parts
The DT200WR Chamber and Silencer joint was leaking exhaust and oil, so I used liquid Gasket and this product.
When I bought it used, Aluminum Tape was wrapped around the joint, but if I look at the service manual, it seems that the same Parts are attached by OEM.
It was a little bit tight to install, and it was difficult to insert it into the Chamber with this product on the Silencer side.
To be honest, the texture is likely to be ruined quickly if stored outdoors, but it's so cheap that it looks good to replace it with every Silencer cleaning. I hope they continue to produce these parts.
View detail
To CRM 50
I thought that the product was short but I managed to attach it.
OEM Joint had Oil blemish, but it seems that there is not leak together with MORIWAKI heat-resistant Seal agent.
View detail
OEM is not available
Parts that are no longer available with OEM Product are precious Parts. Although Rubber's quality is inferior to OEM, its price is also cheap so it is used exclusively as a consumable item. Since I do not know Manufacturer selling outside KIJIMA, I want you to continue selling for a long time in the future. View detail
the expendables
It is a consumable item as others are told. A fine Crack crack will appear in 2 to 3 months after installation. However, it does not mean that it can not be used with it, and I am using it for one year without exhaust leakage. I bought a spare because the price is cheap, but it seems there is still no need for exchange. View detail
It was the Chamber of CRM250AR which was used this time, and the End pipe of a Chamber and the Size of the Silencer were Exactlies. I also regard a Rubber as it not being too soft too firmly and being a just right raw material.
It was the Chamber of CRM250AR which was used this time, and the End pipe of a Chamber and the Size of the Silencer were Exactlies. I also regard a Rubber as it not being too soft too firmly and being a just right raw material. View detail
It exchanged last time, and since exhaust leakage had been cracked and carried out in one year, it exchanged. Since it is consumable goods, let's change briskly.
It exchanged last time, and since exhaust leakage had been cracked and carried out in one year, it exchanged. Since it is consumable goods, let's change briskly. View detail
"""Let's connect as long as the force""""It uses as a joint of a silencer with a chamber. It is needed especially when the manufacturer of aftermarket parts, and a chamber and a silencer is different. Although the liquefied heat-resistant gasket was tried
"""Let's connect as long as the force""""It uses as a joint of a silencer with a chamber. It is needed especially when the manufacturer of aftermarket parts, and a chamber and a silencer is different. Although the liquefied heat-resistant gasket was tried once, exhaust was leaked and I reached this product. Attachment is very easy. It ends with one slotted screwdriver. As packing is a rubber, I'm not sure how long it lasts but it is consumable goods. I hope it is no longer be sold. " View detail
It is used for suzuki TS200R. I think that it becomes this size mostly in case of a 2st off-road silencer. KDX of a kawasaki is fastening an authentic positive one by the rubber joint, and since the pure silencer of TS binds a joint with a metalli
It is used for suzuki TS200R.
I think that it becomes this size mostly in case of a 2st off-road silencer.
KDX of a kawasaki is fastening an authentic positive one by the rubber joint, and since the pure silencer of TS binds a joint with a metallic gasket tight, when the silencer of an external article is purchased, a rubber joint of this sort is also needed.
Although it is core information, since Ohtori Messer's silencer is the same joint structure as a pure silencer, it is rubber joint needlessness.
Although the parts of RIMESSA are the elegance of a phantom now ... Very well cracked about use 2 year, although the small size of the still more nearly same goods is used also for RGV gamma.
Since heat load is also a large portion, I consider it as it is better to have been businesslike with consumable goods, and to spare and exchange.
View detail