【KIJIMA】Silencer Joint Packing Review
It is used for suzuki TS200R. I think that it becomes this size mostly in case of a 2st off-road silencer. KDX of a kawasaki is fastening an authentic positive one by the rubber joint, and since the pure silencer of TS binds a joint with a metalli
It is used for suzuki TS200R.
I think that it becomes this size mostly in case of a 2st off-road silencer.
KDX of a kawasaki is fastening an authentic positive one by the rubber joint, and since the pure silencer of TS binds a joint with a metallic gasket tight, when the silencer of an external article is purchased, a rubber joint of this sort is also needed.
Although it is core information, since Ohtori Messer's silencer is the same joint structure as a pure silencer, it is rubber joint needlessness.
Although the parts of RIMESSA are the elegance of a phantom now ... Very well cracked about use 2 year, although the small size of the still more nearly same goods is used also for RGV gamma.
Since heat load is also a large portion, I consider it as it is better to have been businesslike with consumable goods, and to spare and exchange.
Responses
Other reviews
This is a standard component that seals the Well and Pipe together.
[How is it used?
Black dirt was dripping under the joint between the Chamber and Silencer, so I checked the packing and found a small amount of exhaust oil leaking out. 。 Packing was replaced about 6 years ago when the Chamber was cracked and replaced, so the surface was also cracked and had reached the end of its life span! 。 Still, it is amazing that there have been no problems for six years.
How was your experience with it?
I have been using it as a standard for some time and it is Just fit.
How did it compare to other products?
It is the one and only component that cannot be compared.
[Points to note]
Although Large is strong even when used in its original state, experience has shown that there are two key points to increase durability.
(1) Do not throw away the old part Clamp you removed, but use it (1 piece) 。 The new part has two Clamps at the front and rear ends of the packing, but by adding the Clamps from the old part to the center section, three Clamps can be used to secure the packing more securely and stably for a longer period of time.
2) Apply heat-resistant SiliconSealer to the joint of the Pipe (the part where it plugs in) and the entire inside of the Packing, and assemble. (If you are concerned about the appearance, wipe off any protrusion.)
Other items that would be helpful
Items to buy together:Silicon-based oil-resistantGasket Ultra CopperRTVSilicone
View detail
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily.
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily. View detail
Valuable Parts
The DT200WR Chamber and Silencer joint was leaking exhaust and oil, so I used liquid Gasket and this product.
When I bought it used, Aluminum Tape was wrapped around the joint, but if I look at the service manual, it seems that the same Parts are attached by OEM.
It was a little bit tight to install, and it was difficult to insert it into the Chamber with this product on the Silencer side.
To be honest, the texture is likely to be ruined quickly if stored outdoors, but it's so cheap that it looks good to replace it with every Silencer cleaning. I hope they continue to produce these parts.
View detail
To CRM 50
I thought that the product was short but I managed to attach it.
OEM Joint had Oil blemish, but it seems that there is not leak together with MORIWAKI heat-resistant Seal agent.
View detail
OEM is not available
Parts that are no longer available with OEM Product are precious Parts. Although Rubber's quality is inferior to OEM, its price is also cheap so it is used exclusively as a consumable item. Since I do not know Manufacturer selling outside KIJIMA, I want you to continue selling for a long time in the future. View detail