Reviews
Tightened with a slotted screwdriver.
Used to replace an oil line. It seemed to be able to close it with a hexagon, but it didn't fit slightly. I think it is a millimeter. View detail
a little expensive
10mm on brembo OEMHose, works well.
I like the fact that there are many Size options.
It is more expensive, but Individual Youth offers Quantity:2pc. Set is enough, so Quantity is wasted.:Better than paying high Gold amount for 1 Set of 10pcs.etc.
However, I think there are cases of multiple Wiring, so 4 to Quantity:Variation of 1 Set of 6pcs. is also desired.
View detail
Does a wonderful job securing the largest sized breather hose
About quality and texture - The 15.5mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 15.5mm hose clamp does a wonderful job securing the largest sized breather hose to the barbed hose fitting and breather cap within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 15.5mm hose clamp is the 12mm breather hose for connecting the catch can to the engine via the breather cap for ventilation and drainage purposes. Difficulty of installation - The installation of the 15.5mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 15.5 mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 15.5mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
A much neater option then using a zip tie
About quality and texture - The 13mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 13mm hose clamp does a wonderful job securing the breather hose to the barbed hose fitting within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 13mm hose clamp is the hose connector that allows for a change in breather hose size from 12mm to 5mm as generally for the motorcycles I work on do not have the small barbed hose fitting on the motorcycle side. Difficulty of installation - The installation of the 13mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 13mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 13mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
Does a wonderful job securing the breather hose to the barbed hose fitting
About quality and texture - The 9.5mm hose clamp from SP Takegawa is made from spring steel to maintain it's shape and finshed with a trivalent chromate treatment for prolonged corrosion protection, the quality from the overall fit and finish is perfect. About the feeling of use - The 9.5mm hose clamp does a wonderful job securing the breather hose to the barbed hose fitting within the catch can system and is a much neater option then using a zip tie, with the end result being a professional looking installation. Products to buy together - A key product to buy together with the 9.5mm hose clamp is the hose connector that allows for an increase breather hose size from 5mm to 12mm as generally for the motorcycles I work on do not have the small barbed hose fitting on the motorcycle side. Difficulty of installation - The installation of the 9.5mm hose clamp is a simple task that took 0.1 of an hour to complete. Some slight mechanical aptitude and the use of basic hand tools is all that is required to position the hose clamp to secure the breather hose to the barbed hose fitting. Cost performance and comparison with other products - I find the cost of all the products SP Takegawa sell to be on par when compared to what most other companies sell their products for and the 9.5 mm hose clamp is no different. About shipping and packaging - With there being no cost difference between sea freight and EMS for the 9.5mm hose clamp, I chose EMS for an earlier arrival date. The part was extremely well protected while being covered in bubble wrap and surrounded with air pillows in a sturdy cardboard box. Any concerns, cautions, or advice when purchasing - For my location, purchasing small common use products like this from Webike Japan is the best option when combining multiple parts together if you are also taking into account the shipping cost. View detail
Required Size for Koken Hose
I bought a battered 900SS (900SL) and am Restore.
DUCATI has adopted OEM brembo Master Cylinder and Caliper, but DUCATI of this era has Parenthesis bad Square Type Reserver tank integrated Master Cylinder, so it is often replaced with Reserver tank separate type. However, DUCATI of this era has often replaced the Master Cylinder with a separate Reserver tank.
After 30 years, such brembos are already in shambles, and if they are stored outdoors with no maintenance, they must be in pretty bad shape.
Hose connecting Reserver tank and Master Cylinder, but it is basically Rubber.
If you use a cloth-wrapped hose made by bremboOEM, it is still fine, but if it is not a cloth-wrapped hose made by another brand product, the surface should be white with pushing.
If a translucent Oil Resistant Hose were used, it would be so stiff that it would be impossible to pull it out.
So, I bought a cloth-wrapped Hose kit from Koken to replace it, but the problem is that this Hose kit does not have a Hose clip in quantity.:2pc. Only Set should be included.
No, normally it should be Large sturdy with it, Cut to the required length and fixed, but the rest of the Cut should be too short to be useful.
However, if it is cut well and used in two places, there will not be enough Clip.
Here is a Clip set for such occasions.
You don't have to use such an expensive Clip, you think UniversalClip is fine, right?
However, this is not the case. When bremboOEMTank and KOKEN Hose are combined, this Clip must be used to achieve the best tightening.
To reproduce the same tightness, you should definitely use the screw type.
Since it is a plain steel clip with a black coated surface, it is rather easy to rust it, so if you are concerned about its appearance, it is a good idea to replace it periodically.
View detail
They used to sell them at Home center.
[How is it used?
I was lucky enough to buy a used SEROW225 WE Tank, but it did not have a Fuel Cock, so I bought Yamaha OEM Parts from Webike, but I forgot to order the Hose clip....
When I went to install the Fuel Cock, I realized that it would take too long to order it again, so I went to a local home center, but no matter how much I looked, I couldn't find the product I was looking for. Hose Band (screwed in) is not what I'm looking for." but...
In the end, I gave up and bought it from Webike.
Did you receive the item as per the Image?
The original OEM Clip for Yamaha SEROW225 is a simple needle gold type part, but if I am going to buy another brand product's Clip, I wanted a well-made type, so I looked for it in Webike's product introduction column and bought this product.
The product was as per the standard Image.
How did you like it?
It is a small but reliable and secure product that fixes Firmly and Hose at the Joint.
The firmly attached part is tough to install with bare hands except for those who have a strong grip.
[Points to note]
A slight difference in size can be managed by brute force, but too large or too small can be problematic, so do not be in a hurry to measure the outside diameter of the hose before ordering the required number of pieces.
How did it compare to other products?
There are many similarly designed hose clips available from other companies, but all of the Manufacturer's products serve their purpose well! (As for Clip, I've never had anyone grab a shoddy product before.) 。
Other items that would be helpful
Point and hang of installation
As a matter of course, let's pass the Clip through the hose first before jointing the hose.
I'm embarrassed to say that after plugging Hose in the past "Oh, I didn't put Clip in." What a mess.
[ITEMS TO BUY TOGETHER
Depending on the time and circumstances, fuel hoses also deteriorate over time, so if your old fuel hose is worn out, you should replace it with a new hose. (If the fuel hose is hardened and has a crack in it, you never know when a trouble may occur.) 。
[Opinions and requests to Manufacturer
When searching Webike for products of similar design but with different product names for each manufacturer, it is difficult to find the product you are looking for. Search name I was lost in
View detail
The wide width makes it difficult to merge into the soft Hose!
It is a simple steel hose clip with a single body, and is not a product with any significant features.
However, of the many types of hose clips in the world, the least expensive ones are overwhelmingly those with bent wires.
The hose clip certainly works, but the clip is not good for the hose....
The Clip is wide, so it is overwhelmingly difficult to merge into the hose!
Of course, it is gentle to the Hose, and the knob part is easy to pinch when frequently putting on and taking off, and the pinching part does not tilt, so work time is not wasted.
OEM should also use this shape of hose clip for the Large thing part, but I appreciate that it is cheaper than OEM.
The claws areQuantity:Quantity on the 2pc standing side:Pair (for Left and Right) is connected is also easy to use and GOOD in a sober way.
The surface anti-corrosion treatment is also black colored zinc plating (probably) like OEM, so it is an unquestionable alternative to OEM.
And even if there is a surplus, there is nothing wrong with keeping it on hand.
View detail
It's a little thicker.
The normal Φ8 hose clip is too thin and too tight, while the Φ10 hose clip is too stiff.
It is best to use brembo Hoses, which are much cleaner than other manufacturers' Universal Hoses.
And here is the Hose clip that will be the best size when using bremboOEMHose.
When I use UniversalHose clips from other companies, they are either too tight and almost shred the surface of the Hose, or they are so stiff that the Clip is almost ineffective!
To be honest, even without a hose clip, the place is not likely to come loose in normal use, and at worst, a Tie Wrap or similar would be fine....
It is recommended to replace the Tie Wrap Fixing when you are not busy.
In addition, the A little thicker than the other Clips." This feature makes it ideal for Fuel Hose Clip, which has a thicker and thicker insert.
View detail
Essentials for Hose Replacement
Fuel Hose hardens and deteriorates, but so does the Clip:Rust, broken, spreading. It's also cosmetically good! View detail
As an old Motorcycle Spare
Since Fuel Hose and Fuel fliter were purchased, Band was also purchased,
Unifying Manufacturer gives a sense of security.
View detail
For fixing the hose!
CUB I used it because I added a spare tank to my It is inexpensive and stops well. View detail
Is good
The company's SiliconHose could be securely tightened.
Well, the price is a little Neck....
View detail
CUB I put it on the Blowby hose of
CUB I put it on a Blowby hose of The price is cheap and it is a Repeater. View detail
I have been using it for a long time because it has a good fit.
I have been using it for a long time because it has a good fit.
I usually use Black, but it seems to be out of stock, so I bought this one.
I am always worried about rust since it is not Stainless Steel.
Material of the same Size from before.:Waiting for Stainless Steel.
View detail
power clamp~!!
Kitako cable clamp. The old clamp is a cable tie.. It's an expensive motorcycle, but it was a shame. It was tied up with a black cable tie, which damaged the appearance. The Kitako clamp is made of metal and can secure the cable tightly, and the silver color matches the handle very well. It looks luxurious. It's good to apply lock tight when you fix it. Thank you. View detail
Used in RZ250 Fuel Hose replacement
I also bought Clip to go with KIJIMA's Hose that I purchased.
I matched it to the diameter, but did not use it this time for fear of Gasoline leakage because the Clip was not nearly as effective as the diameter of the Cook's Nipple when it was installed.
The same product is bundled with KIJIMA's Hose that I purchased, but the diameter of the clip is slightly different from this, or maybe the included clip works properly and is usable.
I bought it with peace of mind because of the claim that it could be used with phi;00 Hose, but this time it was a disappointment.
View detail
It's neat and classy.
Monkey 125 2023 model. It doesn't stick until the end. But it's not strange or anything like that. There is room in the hole on the side where the wires are (even though I added wires for the charger and fog light switch), but there is no room on the handlebar side. When you tighten the bolt, it tightens and clicks into place. It looks much better than traditional cable ties. I highly recommend it. -------------------------------------------------- -------- Monkey 125 2023. It doesn't stick to the end. But it's strange or not. There is a hole in the wires (even though I added a charger, fog light switch wires). If you tighten the bolts, it's just bitten. It is much better to see than conventional cable ties. It is recommended. Powered by Google Translator View detail
Replace with new one
When replacing the brake fluid, the hose clamp was also replaced along with the oil hose.
It was helpful that Single Item sold it at an affordable price.
View detail
I like it~ Good~
After tightening both sides tightly, there is a slight gap in the larger diameter part.
Of the two, one didn't even hit the mark... ㅠ
Still, after removing the cable ties on both sides and replacing them with these, it looks prettier than before.
I hope you enjoy it for a long time!
If you are purchasing, please keep this in mind~
I like it~ ---------------------------------------------- ------------ After tightening both sides, the big diameter is a bit of a gap One of the two was a little fits .. ㅠ Still, it looks more beautiful than before, after changing it with this without cable tie on both sides. I hope you write it well for a long time! If you want to buy, please refer to it ~ I like it ~ Powered by Google Translator
View detail