Stc.Design Motorcycle Motorcycle Parts Reviews

Filter

Write a review and get Webike Points!

Reviews

Handlebar Bracket USB Port Kit for DAX125 & Monkey 125 (JB03)

STRIKER

13 May 2024

STREET CONCEPT Full Exhaust System

Fits: YAMAHA YZF-R25

Japanese Webike user

4/5

Ideal for lightweight

Installed on 8BK-RG74J.

No loss of horsepower with regulated engines = can be converted by replacing the Exhaust System. but there was not much change at the JMCA, where the regulations are tighter.

In the 250cc class, the Large body only varies by 1 to 2 horsepower no matter which Exhaust System is selected, so this Exhaust System is recommended for weight reduction purposes.

As for the sound, the 8BK is almost 90db OEM, so you hardly notice any change in volume, but some parts have a thicker sound depending on the RPM.
In terms of sound quality, I think you would feel more change with Planus or WR's Slip-on Silencer.

The quality, however, the accuracy of the front pipe was quite poor, and it did not fit neither the Engine nor the Center pipe, so it had to be installed while bending it with Lever.
Although less expensive than other Full Exhaust Systems, it would have been nice to have a more accurate product.

When installing the Silencer, it is recommended to temporarily fix the Exhaust Band and Bracket and then install the Bracket on the body of the vehicle, as it is quite difficult to install the Exhaust Band if you follow the Instruction Manual.

Also, although not mentioned in the Instruction Manual, it was necessary to change the Wiring position of the O2 Sensor.
The OEM position is fixed in front of the Clutch cover, but once removed and placed through the rear.

Although it has a few drawbacks, it does not look like other people's and can be lightened to a large width, so I think it is recommended for people who are visually oriented. View detail

DUNLOP

12 May 2024

D604 [80/90-17 44P TL] Tire

Japanese Webike user

4/5

Anyway, it was hard.

The CT125 Rear tire GP-5 has 2,0mm left, so I'll change it after a few more runs, but I'm running a GWCampaign, so I'll buy the Tire while I can, and I'm in the On 9, Dirt 1 ratio here, so not completely On road, I decided to go Adventure oriented.
So, after much deliberation with the well-reputed Anakee STREET, I decided to go with D604, which has no Reviews at all, as I am a minority, and write my first Review.
In a review by a certain Large River in South Brazil, the only negative image was that it was hard and vibrated.

After touching the one that arrived at my house for a bit, I was prepared that it would be hard and tiring, as it reminded me of the T63 thing from company M.
Now, when I got it in my hands with the usual Pattern, I already wanted to replace it, and I had planned to replace it next month, but I started to do so (laughs).

As you might expect, there is a direction of rotation for installation, so we carefully checked the direction of rotation before starting work.
This is my first time to replace Tire on CUB, but I will follow the theory here.
The GP-5 has a soft bead and was relatively easy to remove.
Now, let's start the assembly.
As usual, apply a generous amount of Bead wax.
Unlike off-road vehicles, we do not want to scratch the rim, so we use rim protector while working.
It's already hard even to fit the first time!
Fit the One Side and put in the Tube. These are not so fiddly.
Turn it over and put the other side in, but it is hard anyway!
After fitting half of the wheel, I held it down with my foot and lever it in, but the remaining 20cm or so was tough!
The installation was done carefully, boldly, and by brute force.
We managed to complete the work without any holes in the tube and with a clean rim.
I ran the car for a while, and it is true that the slight vibration from the Rear has increased, but it is not at a Level that bothers me that much.
Grip is often seen as such and such, but well, it is a CUB, so it can run and stop normally.
We don't ride in the rain, so as long as the dry grip is good, it's fine!
The groove is somewhat larger than GP-5, and the block is also larger, but the tread surface and SIDE are harder, so I think it is easy to be played on the dirt.
Muddy terrain is likely to Stack if not driven well, but the CUB does not have that kind of driving ability to begin with.
If you are used to working on CUBs with Spoke wheels, and if you are used to working on them, and if you drive in an adventurous manner, recommendation.
I thought that GP-5 would be easier to work with when Puncture was done, and that in the end the standard Tire would be the best. I thought that the standard Tire would be the best in the end. View detail

RISE CORPORATION

12 May 2024

PlatingRectangular Mirror

Fits: HONDA BENLY50, HONDA CB250R, HONDA CT110 HUNTER CUB, HONDA DAX, HONDA glom, HONDA XELVIS, HONDA Night Hawk, HONDA JADE, HONDA HORNET, HONDA GB250 CLUBMAN, HONDA DREAM, HONDA CL250, HONDA VT400S, HONDA R100 ROADSTER, HONDA GB400, HONDA CB400, HONDA CB400SF, HONDA BROS, YAMAHA RENAISSA, YAMAHA SR250

Japanese Webike user

4/5

It's very cost effective.

It is OEMMirror-like enough to be satisfactory for the price.
Plating is clean, mirrors are not distorted, and there is no blurring while driving, so rearward vision is good.
The difference between OEM and Large is that the ROD is shorter (lower) and the black parts that look like shock absorbers are just materials.:It means that it is a Plastic Cover. Of course, there is no way to add a shock absorber at this price, so it makes sense.
Overall, I think this is a good product with high cost performance. View detail

[NISSIN Repair Parts for Master Cylinder] Piston Set Only For 1/2 Inch

«
1
2
3
4
5
6
7
8
...
1555
1556
»