Reviews
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Requires ingenuity in installation
Model YZF-R25
(8BKRG74) 2022 MODEL
I have prepared the following items to install the brake pedal side.
KITACOAluminum Bracket
BracketWidth:20mm/Thickness:3mm
Hole Size:φ6
Length:60mm
Spacing:40mm
YamahaOEM
Brake fluidReserverHolder
(2015 1WD-F582E-00)
JointZ type bracket with 3 holes
BoltM6×12、M6×15、M6×20
Flange nutM6
Mounting position is set at 60mm back and 40mm up, which is the position with the least interference.
On the shift pedal side, the included shift rod does not fit well, so it will be replaced at a later date.
After the installation, I think it was better to check the position here than to buy expensive Rear Sets and make a mistake. I learned a lot.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA YZF-R3, YAMAHA MT03
Brake Side
Model YZF-R25
(8BKRG74) 2022 MODEL
Brake Side Image
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Partially made of Steel, it is prone to rust.
[How is it used?
The Normal pedal was a bit tasteless, so it was attached to the Brake pedal version up.
Was the one you received as per Image?
The size was larger than expected and easy to step on.
Was the installation difficult?
Install the Normal brake pedal so that it is sandwiched between the Normal brake pedal.
Plus screw allows installation with a single Driver.
How was your experience with it?
The driving operation is easier because there is more area to step on.
However, it took some time to get used to it because of the slight increase in height.
[Included Parts:were they on?
Mounting Screws, Mounting Hardware, etc.
[Was there anything that disappointed you?
Body is Material:Aluminum, but the Plus screw and the bracket on the reverse side are rusted with steel. Especially when the Plus screw is rusted, it is difficult to remove it.
▼This is a common design, but you can enjoy a slightly Mischief atmosphere.
I think the discomfort during operation depends on the person.
View detail
Has the Shift's entry been further improved?
I purchased this product for the purpose of further improving the shifting of my MONKEY125 (JB02). First of all, I would like to conclude that I am honestly not sure about it? I originally installed KITACO's Shift link, so I thought it would improve the shift entry compared to NORMAL, but it didn't.
I had a short test drive, and I was pleasantly surprised by the improvement? I am planning to go on a long touring trip. I am planning to do long touring from now on, so I expect that my impression will be different. If I can confirm the improvement, I will give my impression again.
View detail
Fits: HARLEY-DAVIDSON XL 1975-1987, HARLEY-DAVIDSON FX 1971-1984, HARLEY-DAVIDSON FXR SUPERGLIDE
The product is good, but it would be better if there were more details on how to install it.
It may look a bit large, but I think it is an item that can easily change the atmosphere to a large size. View detail
Fits: YAMAHA SR400 19, YAMAHA SR400 19, KAWASAKI Z125 Pro, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR400, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500
Casually PetitCustom
PetitCustom is completed by simply removing the conventional Rubber cap from the front fork cap and replacing it with the new ChromeCap. Conventional Material:There is no concern about degradation with Rubber, and you will get an improved texture of Chrome's look and feel. View detail
Large things are not explained! It is much shorter than OEM!
Caution before performance crap! This suspension. It's short. (Angry)
It is listed as TW200/225 compatible, and since there is no explanation, I thought it would be the same size, but it is much shorter than the OEM suspension.
If it wasn't the same size, I would have hoped there would have been an explanation. If I had known it was short, I would never have purchased it!
Seeing things, Once I don't have a ShacoTan in my off car. I paid high gold to buy Garbage. I was disappointed.
I doubt the designer's Sense, even if it's the old fashioned Ska tune type Custom. no Sense!
However, I paid a good amount of gold for it, and since it has been sitting for about six months after purchase, I would not be able to return it......so I am in an atrocious mood,
Since it has a coilover function, I extended it to the limit and installed it. Still, it is a little shorter than OEM. Too bad.
Comparing the appearance before installation, the damper section looks thinner and poorer than the OEM.
Pre-road is installed as shipped. Attenuation is at its lowest.
The front side is equipped with a Cartridge emulator and pre-road is also applied.
When installed, the suspension itself is shorter, but the spring rate is higher from the beginning and the sag is reduced, so the Rear ride height is higher at 1G's ride. (The optical axis is lowered.)
This is not the kind of thing I wanted, but I feel ・・・・ indescribable・・・・
Normally I wouldn't want to give it even 1 star, but after riding it... not bad ・・・・
Things are not bad.
It's very well controlled and of high quality. It is clearly different.
Completely stiffer for on road use. The front end tends to cut into the road as the vehicle's ass rises higher than the OEM during cruising.
It picks up fine Gap and has a lumpy feel. However, when stepping on the Gap or swell while turning, it becomes a crisp and snappy leg without wobbling. It is honestly easy to ride.
I think this will increase the risk of cocking up when going off-road, and I don't think it will be a comfortable ride...
It is intended for long-distance travel with luggage, so maybe a harder taste that is not as heavy is not a bad thing...
Supple in the beginning, stiff in the back. Stroke is up if you want....
I didn't get what I wanted due to the lack of explanation, but things are good from a different perspective and well, this is what I got.... It was the Rear Suspension that made me feel indescribable.
I don't like even 1 star if it's just for the emotion. But considering the performance of the product, it's not bad at all, in fact, it's rather admirable. I rated it as 3 Stars because of this.
It is very good for on road driving....
Whatever the case may be, I would have liked to have seen a better description of the product.
This would be good for those who are customizing for on road or want to lower the ride height.
The stiffer design may be suitable for heavier people or those who carry a lot of luggage.
Sorry for the poem.
View detail
For use with the 3RW1 that is not the appropriate model year (but requires modification).
Compared to NORMAL, the large size of the footrest surface is obvious.
It is stable, but its thorns are sharp and long, so please use it with hardy boots that can shave off the Sole.
When used in 3RW, the Right Side must be considerably reduced to be able to be overthrown.
And even if it is installed after much effort, the rattling is so great and the return in collapsible mode is so weak that further modification is required.
If you are concerned about the details or if the modification is troublesome, you can install the expensive Bolt On. "ARE" is probably a good idea
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE
I don't feel much.
I don't feel it much. I don't feel a huge change in the gear shift. I feel like the gear stops significantly when I go up from 1st to 2nd. View detail
Fits: HONDA Today, HONDA Today, HONDA DIO(4Cycle), HONDA DIO(4Cycle)
Repair is completed at a low cost!
Installed on ThirdMotorcycle's Today that goes to the nearby Convenience, replacing an OEM OEMRear Suspension that had been scuffed up and deteriorated. The price is very low, but I have had no problems with it! I am Large satisfied with the low price and the refresh! View detail
incomprehensible
Instruction Manual is too complicated and difficult for beginners. I think some knowledge is necessary. View detail
Those with big feet need to get used to a lot of things.
The work itself is BoltQuantity:It takes only 10 minutes because it only touches 2pc.
After installation, we went out for a test run.
At first I was not sure how hard to step on the pedal, and sometimes I wanted to go from first to second gear, but I soon got used to it.
All you have to do is step in with a firm clank!
What I was more interested in was the foot placement.
My foot is 28.5cm and the Outsole of the shoe is over 31cm.
As you can see from the picture, if you set the angle where the Down side Pedal does not hit the sole, the height of the Up side Pedal will be raised, or if you install the Up side down, the Down side will always hit the sole….
Anyway, it is quite tight for people with big feet.
There are various inconveniences, but I don't want to damage my leather shoes! I highly recommend it to those who don't want to damage their leather shoes!
Because that's what I bought it for, too.
It is not the Parts for which we are looking for a sense of operation!
View detail
Fits: HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
I bought it just for the color.
I won't know for sure until I ride it for a while, but I bought it just for the color, so I am not particular about its performance. View detail
It looks good!
NC42Rear suspension was leaking Oil and I couldn't afford OEM because it was too expensive.
The item received is clean with some SmallWound! 。
Installation was not possible because the Bolt under the Right Side interfered with the Exhaust System to remove the OEM! Others were completed Smoothly. The upper part of the Shock was not easy to install, so I applied a little Chain oil as a reference to others and it went in. Also, one of the lower side had to be tapped a little to fit the holes in the mounting position. Also, it was impossible to mount the pon, so I had to extend the overall length by about 8mm to complete the installation.
The ride is not bad, but it feels soft, so I will adjust it. I don't know about durability, but there seems to be no oil leakage and no initial defects.
View detail
Easy to install
I had an Indicator, but I replaced it with this one. It's not very noticeable, but the price is low, so I guess it's okay! View detail
Getting the Center out is the hard part.
I was prepared for BALI and Small scratches, but I can't get the Center without modifying the Brake Panel side.
I also bought a 4mm Sprocket spacer but I think it will be useless.
Also, there is some distortion, so if you want to assemble it tightly, we recommend a reasonable price.
View detail
It cannot be pontooned. But Rim width is Quantity:Pair (for Left and Right) I like the fact that it's all even, etc.
I purchased Front 3.5J and Rear 4J. Please be careful. Personally, I think that the depth of the rim is more than enough.:Pair (for Left and Right) I bought it knowingly because I didn't want it to be a "one-size-fits-all" type of arm. If you want to mount it on your car, you should use KITACO or GKURA's Quantity.:It is better to buy a Set product. View detail
It didn't work
I tried to install it, but I have it set to short suspension.
What a surprise, Chain didn't hit Roller ….
I will try to install it again when I change to Normal suspension.
It would have been nice if you could have written something about not being able to use it if it's Lowdown.
A little disappointing.
So we do not know the effect of the installation.
View detail
Shift Pedal
GizaGiza synthesis on the part where the clutch is attached looks like a bad lick! View detail
Very good looking, but...
Pulling on the brake wire is important, but securing the rotating bracket is impossible with a screw lock, and the bracket inevitably moves. However, I think that a more ingenious bracket is needed instead of just using the OEM bracket. View detail