Reviews
Fits: KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650, KAWASAKI W650
Nice chrome parts
It had a shorter tail than the original and a Lukatsu tail brake light, so it had a sense of unity, and it was nice to have all the additional parts to attach a license plate. View detail
NORMAL Screw is lame, right?
I wanted to replace the NORMAL Screw because it smelled like a potato, but I didn't like the gear-like Knob from another Manufacturer.
I decided on this one, because it is a Round Type, which has the drawback of being slippery when turning it, but it was Large and durable when I was wearing Gloves, which prevent my fingertips from slipping. If it is not wet, you can turn it with bare hands. If you are looking for practicality, the gear-shaped Knob is definitely easier to turn, but I decided to go with this one because of its looks.
I love it
View detail
Looks good
I don't know if the installation is defective, but the right side is flush with the frame, but the left side is about 2mm above the frame. View detail
I finally got there.
The MONKEY125 splashes mud on the engine, so I installed a down fender and looked at it, but it did not solve the problem completely.
So I was researching on the Net and came across this product.
Fit feeling is good. Drilling Double-sided tape was a little uncomfortable, so I Neodymium magnet, rubber type, 1mm thick. The adhesive was applied and installed on all joint surfaces.
There is no sign of falling off so far, but as an insurance measure, we have drilled a small hole in the side of the mudguard and connected the Brake hoseGuard to the mudguard with an in-hemp palm to prevent it from being lost.
I bought a good product.
View detail
As generally expected
I bought this for RonTwo.
Alafi Return.
Before Return, I had only ridden Vixque and rarely rode at high speeds, so I did not understand the large aerodynamic drag of a naked motorcycle at high speeds.
I was not convinced that it was hard to run at legal speeds due to the large aerodynamic drag of the bike, even though the bike can reach the legal speed limit at high speeds in Japan without even half the speed of the Meter.
My impression is generally in line with expectations.
For driving at legal speeds on highways, the resistance is reduced considerably and it is easier to drive. Plusα speed when overtaking is also much easier, and is generally as expected. The height of the screen is a little lower than my eye level.
The only thing I feel a little minus is that the wind, which seems to come from the slit in the center, just touches the top of the helmet, and I feel a lot of noise and vibration. Once you get used to it, it's not so bad, but it's a little too large and at low speeds, it's not so bad. (in town) But I can feel it, so it might bother some people.
What was surprising was that it was originally attached to the MeterCowl as well, [Color] I was going to buy Smoke, but because of inventory and because I was going to remove it when not doing basic RonTwo, [Color] I bought the Clear, but the Screen picks up the light from the Headlight and the whole thing glows dimly. I don't drive much at night, but I think it's quite beautiful.
View detail
To repair Exhaust System that has fallen over
A fall damaged AKRAPOVIC's Silencer
The outer Sticker was also damaged, so it looks like a wreck.
At first I bought an external UniversalSticker and stuck it on, but the size did not fit at all and Silencer itself was thought to be a fake lol.
I knew I needed OEMSticker and found it on webike.
I forgot to measure the size when I removed the damaged OEM sticker, so I measured the mark on the sticker and chose this product in the Large body size. The material is Aluminum or something like that, so if you make a mistake once, you will not be able to use it, so please make sure to align it properly before attaching it!
View detail
good-looking
The product is a Kawasaki OEM Product and was installed without any distortion or problems.
It also looks better.
View detail
Genuine Pyramid Plastics Enduro Fender for 2020 MT07
A customer wanted to get an extender for their MT07 to help stop water flick from the front wheel. Having not used one of these before on any bike, I asked the customer what they preferred. They chose this one from Pyramid Plastic. Good choice from doing my own research. The fender extender was not hard to find once you put your bike details in the website and the options appear. The extender was not overly expensive and added to a few other small parts in my order, I had them all shipped via EMS. I do have more than one item per order as this does cut back on the shipping cost somewhat. The order arrived in 5 days from being shipped and was well packaged and in 100% perfect condition. The fender extender came in the Pyramid Plastic sealed packet and was wrapped in bubble wrap from Webike warehouse to keep it safe. You do have the option of using the stick pads for this fitment or better yet, just drill the fender and attach for a more secure fit. This was the route we went. The extender is made of and ABS plastic as far as I can tell and the fitment of this is absolutely spot on. The quality of the part is excellent. A nice matte finsih which does go very well with the bike anyway too. I did think there may be a slight gap once test fitting but there was no gap at all. Took a little over an hour to do the job right but the result is really good. View detail
It was cheaper than OEM.
The exterior is covered in wounds and is starting to look shabby.
When I was wondering what to do with it, it was about 2/3 the price of the OEM Kit.
This one was sold at a great price, so I decided to buy a set of Quantity.:Refresh with Set.
The important thing is the installation, but the mounting holes are slightly out of alignment.
Some parts were not as readily available as OEMs.
Specifically, the Front Fender has two of the four holes slightly enlarged Large,
OthersShroud manages to stop at one place while pulling the others,
Fork Guard is the same way, with the same order of stops and other innovations.
We managed to attach it without any processing.
Shape is the same as OEM, but material is used for mounting.:Plastic colors are used, and they are not exactly the same.
It's not hard to modify the installation to some extent.
I thought it was for people who wanted to raise the price cheaply.
View detail
Fits: HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125
Good because the price is low and no need to relocate Horn.
Buy this one while you're at it for a down fender in Mukawa.
OEM HONDA Emblem was installed.
Good price and no need to relocate Horn.
Product.
However, my 2023MODELMONKEY125 is
When the Mounting Bolt of the Horn is removed, the Headlight case and the
Remove the front Light as it is stuck in contact and cannot be removed.
Furthermore, remove the three Bolt fixing points of the Light case and put the Light case.
The Bolt was shifted slightly to remove and install the Bolt.
The instruction says to remove the Light case, but remove it completely.
There was no need.
This is a standard custom for DownBracket installation.
I am glad I installed it.
View detail
Easy dress-up
[How is it used?
I wanted to change the look of the SUPER CUB110 (JA59) a bit, and also to have an anti-agitation effect.
Was the one you received as per Image?
Nothing of particular concern.
Was the installation difficult?
You will need a #3 Driver and a 10mm Wrench, nothing too difficult as you just need to remove the License Plate and install them together.
How was your experience with it?
It looks a bit Wilde. I'm not sure how effective it is in preventing agitation (partly because I didn't get something so blatant to begin with). Well, it makes it look more like an Off-road Motorcycle, which is better than nothing.
[Included Parts:were they on?
Nothing in particular, just Body.
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Since the material is Rubber, I don't think I need to worry about it, but I thought it might hit the Fender that comes with the Motorcycle from the beginning, so I put Urethane Seat on it (2nd photo).
View detail
Price suitable
The screw holes were accurate and there are no problems with installation or appearance. View detail
Second purchase of this.
This is actually the second time I have purchased this.
The first one peeled off after about 3 years.
I wanted something else from Japan but couldn't find anything that fit my 2014 GSX1300R HAYABUSA, so I bought the same one.
No complaints other than adhesive life.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50Custom, HONDA SUPER CUB 50Custom, HONDA SUPER CUB70, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA CUB press 50, HONDA LITTLE CUB, HONDA CUB press 50, HONDA LITTLE CUB
Difficulty in weather resistance
Why is it that everyone is so quick to exchange to NORMAL? I was wondering,
Now I know why. After about a year of storage under the eaves, the surface hardens.
ParisParis and tear it up.
View detail
Fits: KAWASAKI ESTRELLARSCustom, KAWASAKI ESTRELLARS
Stretched well.
I bought Tucker to reupholster my old motorbike, and I didn't have the budget to spend tens of thousands of dollars on OEM or custom-made stuff, so I decided to do it myself at a low price. The thickness and texture of the seat is not as good as OEM, but I regretted that it looked cheap when I received it, but after I stretched it, it looks beautiful. The ride quality is also better. Even if I applied anti-slip coating, after applying the brake, it was gapping in front of the car but now it is stable and easy to drive without sliding. The material that looked cheap is now shiny and beautiful. I've never done any DIY before, so I'm a beginner and I'm too lazy to watch YouTube, but I can get by even if I do it haphazardly. Now I'm planning to reupholster it again and put Nylon in it for rain protection and Gel Zab under the Seat for long distance protection. View detail
I miss the colors and design.
Good old-fashioned color and design. View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB 50, HONDA SUPER CUB110
Large satisfied
Installed in CHALY.
It needed a little modification for the CUB, but it is quite good for a little flippant shopping.
View detail
Easy to install, but ???.
Installation is easy, and the design fits well with the car body without any discomfort. However, I think that the reflector should be included from the beginning since ACTIVE also manufactures a reflector. View detail
Y’S GEAR (YAMAHA) Y's Gear Yamaha Single Seat
Y’S GEAR (YAMAHA) Y's Gear Yamaha Single seat cowl
We chose it as a high quality, OEMOption! is
Until the previous generation, this Seat cover, open/close, remove, and install with a key.
One-touch, I was able to do it, but from this model 2015~.
This single seat cover was installed by Bolt.
You can either carry a Hexagonal Wrench with you, or you can use it as a
We need to put Wrench in a handy place on the body of the car.
I can't take it off when I'm out and about!
It's a little weird to put away all those documents.
Looks Large satisfactory!
View detail
YOSHIMURA Fender Eliminator Kit
Item arrived..super fast shipping.3 days arrived.check and all item is in order.never been disappointing.highly recommend.thank you team webike.awsome job.5 ⭐ View detail