Reviews
Fits: DUCATI 899Panigale, DUCATI MONSTER 1200S, DUCATI Multistrada 1200, DUCATI Multistrada 1260, DUCATI Panigale (except 959), DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
For ZX-14R 320Large diameter
If not Titanium, Stainless is sufficient, but it is not sold.
It would not be commercially viable to make the price low at Stainless.
View detail
Fits: DUCATI PANIGALE V4, DUCATI PANIGALE V4 S, DUCATI PanigaleV2, DUCATI StreetFighterV4
It is a product of high design and processing technology
I had installed DucatiPerformance Carbon fender, but I wanted to make the rear area more reflecting, so I changed the spec. to AELLA fender.
When installing, it was difficult to find a way to store the Blinkerretc. cable because the storage space was too small and almost nonexistent.
View detail
Pillion Bar installed (XJR400R.99)
There is some shaving of the OEMFrame, but it was not that difficult to do. The installation method was also easy to understand if you read the instruction manual that came with the product. It took about one hour because I was not familiar with the shaving process. View detail
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE
Speedra Carbon Tail Light Cover
The OEM ABSTail Lamp Cover is cheap, so we changed it to …Speedra's Carbon Tail Light Cover!
The texture will be much better.
View detail
Change the thickness according to the handling.
It is convenient to have washers of different thicknesses in case you need a little more.
* Video:FZr MEETING
View detail
![[NATIONAL CYCLE:National Cycle]Vstream Windshield](https://img.webike-cdn.net/catalogue/images/75533/16971_TS.jpg)
Fits: HONDA PCX150, HONDA PCX
Windproofing, though.
As far as I have been able to find out, I think this item is the LARGEST as a windshield. (At the time of purchase)
I think the windproof effect is solid in the Large size range.
However, in the summer, when parked in the sun, the light was concentrated on the Screen and the inside of the Screen melted.
It is possible to countermeasure this problem by placing Towel or other material between the two, but be careful, as the entire Towel may burn if it is not properly placed.
View detail
![[GTR-Series]Seat Assembly](https://img.webike-cdn.net/catalogue/images/120000/21_TS.jpg)
The ultimate cafe seat.
The Myoga seat is lower and better looking than another aftermarket low seat I had purchased before. My heels are 2mm from the ground where before it only my toes touched the ground. This seat is also more comfortable on long rides. It was also less expensive than the other seat. Thank you, Webike. View detail
The perfect emblem
Nothing makes the Kawasaki Z900RS Cafe look better than this new emblem. The white letters contrasts against the lime green tank so well. An installation guide was included. You will need fishing line and an adhesive remover and lots of patience. But it is worth the effort. Thanks Webike for giving me a great price. Arigato. View detail
Ligh Tech tail tidy
The quality of the components are excellent. Fit is also great, when you figure out how to do it! Zero instructions and resorted to YouTube tutorial from a different manufacturer. The hardest part was actually dismounting the OEM number plate holder. You need to cut the number plate light wire and reroute it. After that it was straight forward. View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Tank Cover (GSX1300R HAYABUSAI type) Twill Weave Carbon
The product is aesthetically pleasing as a twill weave carbon and is well finished. The area of the cover is larger than that of a general stick-on cover, and the appearance of the custom parts is eye-catching, and the practicality of the cover is also reassuring, as it frees the user from the worry of damaging the tank with Belt Bracket etc. On the other hand
Urethane for surface protection [Color] The drawback is that Clear painting must be done by itself. A small amount of liquid Sauce still occurred.
View detail
Increased windshield effectiveness.
I purchased this product for the purpose of reducing wind effects when driving at high speeds.
OVER Separate Handlebars interfere with the Throttle Cable and the Tank of the Master Cylinder.
Handlebar is installed back to OEM (without Spacer).
Well nuts (C-440) are used to join the Base and Screen sections.
The experience of installation is that the posture is shallower than OEM, where the benefit of drag reduction is achieved.
The effect is not that noticeable in the normal posture, but the reduction was noticeable in the sticky prone position.
About the appearance (FRP Black, [Color] (Select Option in Clear)
The Luster feel is good, but as you can see from the light reflection in the Base area in the photo, the surface preparation is a bit lax.
if you are concerned about [Color] It is best to purchase without Clear and paint after priming.
The Screen section is not distorted in any strange way, and it is nice to know that this is also available as a Single Body.
It seems to be #Made-to-Order, so the delivery time may take a couple of months.
View detail
Moped Plate
It is easy to install.I just installed it,
How durable is the Sticker?
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZX-14R
Material:The twill weave pattern peculiar to Carbon products is very beautiful! NEXRAY is indeed the best.
The twill weave pattern is very beautiful Coating. Moreover, it is a NEXRAY product. The product is highly accurate, and there was no distortion or modification of the screw installation position like other companies. View detail
Satisfied with Simple Design
One month has passed since the product was installed, and the height is definitely 4 cm higher than that of the OEMScreen, and I am satisfied with the simple design that does not give the impression that it is just for show. However, the OEMScreen has a step between the cowl and the screen, so there is no difference between the screen and the cowl, but this product has no step between the cowl and the screen, so there is a difference between the cowl and the screen. In addition, the product has a quantity of Screen mounting screws.:Since it is not set, the Screen mounting Screw must be ported from OEMScreen or prepared separately. View detail
If the Bracket is
It is cheaper than some Manufacturer, which is helpful.
It would be helpful if the Stem Cover mounting bracket has a long hole machined in it.
View detail
Just a color
This color is for moving the Bracket as the Stem Bracket mounting position changes. Personally, I wish it had been available in Black. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RSCafe
Here we go!
I used a Stem Cover Bracket for Cafe, and the position was perfect and the angle was adjusted. View detail
Gorgeous.
I think it is the Large type among OEMOption and others.
Installation is easy, but there are some situations where it may get caught when getting in and out of the car because it is a large type.
Please consider those who have concerns about the high Seat height of the car.
View detail
I like Large
When it comes to Rear Sets, I have decided to use Babyface for my racing hooks. I have no doubt about the outstanding accuracy, appearance, and functionality. I have installed it on both of my cars. View detail
Fork Protection
Purchased in hopes of preventing insects and flying rocks.
Installation is done by a type of in-hemp palm clamp, so anyone can do the work.
I think it looks Refreshing and is a good product.
View detail