Reviews
Fits: KAWASAKI ZX-14R
Sale item was cheap.
For a little over 10,000 I was able to buy a Support for the new ZX-14R Crab.
This is an unbeatable price
OEM is weak, so the new Crab and Gale's Small diameter MASTER.
Increase braking power.
View detail
Fits: KAWASAKI ZX-10R
Pad position is subtle
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Purchased to improve serviceability by underlining.
ABSFlareBlock, Hose (635mm), Fitting (20°), Mount Bolt (M8*20) are required for installation.
The swing arm needs to be removed when wiring, so it is quite large.
I used it on a new Crab, but the pad sticks out, so I had to shave about 5mm off.
I was able to do this in about 5 minutes because I had Leutor and TungstenBit, but if you only have File, this is also Large strange.
Weight is Quantity for Bracket and Caliper:It was almost the same as OEM with Set.
The design of the cutting groove was uneven (white spots) and the texture was not good. (The texture was not so good, but the others were good.
View detail
Large modification is required and out of the question as a vehicle-specific kit.
OEM Blinker cannot be installed as is.
The only way is to process this product or Blinker into a Large size.
It is not a Level that doesn't fit a bit, so if you buy it, you should be aware of that.
Incidentally, Webig's conformity guarantee does not cover this degree of processing.
Below is the response I received when I inquired about the conformity guarantee.
------
For more information about the conformity of this product in our company, please contact us,
If the four holes of the product can be installed on the Rear side of the vehicle through the Bolt, the product is considered to be compatible.
Fixing the above to the vehicle. Conformity Assurance The following is a summary of the results of the survey.
View detail
WR3 Frame cap
Is the texture slightly less luxurious because it is plastic?
Rubber packing is also included, so the hold feeling is perfect.
The holes are slightly larger than the holes in the frame, making it easier to remove the frame.
I chose Black, and it matched the Frame and gave me a sense of unity.
View detail
Fits: KAWASAKI Ninja 150RR, KAWASAKI Ninja 150RR
I finally found it, but...
The Disc Rotor in NORMAL is too small and the pad does not hit the entire surface.
Large Disc Rotor must be replaced.
View detail
ZX-6R Fitment
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX636
Fitment Issue
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: HONDA CBR600RR
Complete design error
I installed the pad on a '07 model, but due to an obvious design error, the mount position of the brembocncCrab caliper is 5mm outward gap compared to the OEM disc diameter of 220mm, and the pad protrudes when installed as is.
The disc diameter of 230mm is not so common, and the only way is to shave 5mm off the disc contact surface of the pad and forcibly fit the pad to the disc.
There is no Caliper center, and the center must be adjusted by placing a Shim between the Mount section.
At any rate, it is not a Level product that can be sold.
View detail
Fits: YAMAHA YZF-R15, YAMAHA XSR155, YAMAHA MT-15, YAMAHA XSR155, YAMAHA MT-15
No instruction manual, inappropriate Screw length, unintelligible parts and no necessary parts.
It sucks! You should not buy it. There is no instruction manual, no pictures or description of the Parts. There is no shift arm for some parts that don't make sense, so you can't put it on. 。 In addition, the Stop-lamp code is used for the Quantity:They made me buy it at Set and I can't put it on.
I think this is a Manufacturer that the buyer will only regret. I will definitely recommend another Manufacturer because I need to purchase additional parts and I need to do a lot of processing by myself.
View detail
ZX636-2019 Rear caliper support
Mounted on ZX6R-2022
First of all, the diameter of the Axle Shaft is completely different! The angle of the Swing ArmCaliperStopper is too large for the Axle Shaft to fit through.
I managed to install it, but the Brake Pads were about 1cm outside the surface of the Rotor ….
Dangerous because it is a Brake round!
View detail
Fits: HONDA Rebel 500, HONDA Rebel 300, HONDA Rebel 500, HONDA Rebel 300
For REBEL 250.
OverRACING is expensive, so I bought this one.
The 250 can be installed and used without any problem.
View detail
Impressions at Corner
In NORMAL condition, it was difficult to hold the tank, but after attaching this product, the tank was held firmly and the vehicle was able to run in a stable manner. The price was reasonable and I was satisfied with the Large size. View detail
It will last longer than the Songe.
I was looking for something better and found this product.
No particular problems as long as the positioning and degreasing are done properly. It is a good product because it is thick and easy to grip.
View detail
WR3 Dub Lure Rusley Radiator core guard
[How is it used?
Radiator protection.
Was the one you received as per Image?
It is exactly as pictured.
Was the installation difficult?
It seems to be a good idea to remove the RadiatorTank. I did not remove the RadiatorTank.
How was your experience with it?
It is going to be protected.
[Included Parts:were they on?
Included Parts:were complete.
[Was there anything that disappointed you?
As expected
Other items that would be helpful
Point and hang of installation
I thought it would make noise if I installed it directly, so I put a RubberSpacer between the two.
View detail
Fits: KAWASAKI Ninja 150RR, KAWASAKI Ninja 150R, KAWASAKI Ninja 150RR, KAWASAKI Ninja 150R
BoltQuantity:Mounted with 2pcs.
It is easier to change the front sprocket, after running with a lot of chain oil, oil is flying all around. The look is different from the NORMAL by a large amount. View detail
Fits: YAMAHA XMAX 250, YAMAHA XMAX300, YAMAHA XMAX300
Simple is good.
There are no unnecessary decorations.
There are no adjustment functions such as accuracy.
Instead, I like its Simplicity.
Since the same screw holes are used as those of the YAMAHAOEM Tandem Backrest, the backrest will be slightly tilted when installed at the same time.
but not enough to be bothersome.
View detail
Fits: KAWASAKI Ninja 650, KAWASAKI Z650
NINJA650 Brake Caliper Support
The Caliper supportBody is of high quality and the Black Anodized looks tight and parenthesis is good. If the Bolts were also available, it would be a perfect score, but there is a time-consuming task to arrange the Bolts. View detail
foreign-made
It was written in the description, but it was not Down by 30mm. View detail
Fits: YAMAHA XMAX 250, YAMAHA XMAX300, YAMAHA XMAX300
Simultaneous installation with OEMBackrest is △.
When connecting with YAMAHAOEMBACKREST at the same time, the thickness of this kit will cause the backrest to shift.
Maybe I should adjust it with a washer or something, but I use it as it is.
Even without imposing it as a measure, there are no particular problems with its appearance or strength, but perfectionists should beware.
View detail
For decoration
It is easy to install., I think it looks and feels custom. View detail