Reviews
![[Closeout Product]Rear Brake Caliper Bracket for Brembo Rear caliper support[special price]](https://img.webike-cdn.net/catalogue/images/99779/id5044981_1_TS.jpg)
Fits: KAWASAKI ZX-14R
Sale item was cheap.
For a little over 10,000 I was able to buy a Support for the new ZX-14R Crab.
This is an unbeatable price
OEM is weak, so the new Crab and Gale's Small diameter MASTER.
Increase braking power.
View detail
Fits: KAWASAKI ZX-10R
Pad position is subtle
Inconvenient because the 10R OEMBrake cannot be removed without removing the Wheel.
Purchased to improve serviceability by underlining.
ABSFlareBlock, Hose (635mm), Fitting (20°), Mount Bolt (M8*20) are required for installation.
The swing arm needs to be removed when wiring, so it is quite large.
I used it on a new Crab, but the pad sticks out, so I had to shave about 5mm off.
I was able to do this in about 5 minutes because I had Leutor and TungstenBit, but if you only have File, this is also Large strange.
Weight is Quantity for Bracket and Caliper:It was almost the same as OEM with Set.
The design of the cutting groove was uneven (white spots) and the texture was not good. （The texture was not so good, but the others were good.
View detail
Fits: KAWASAKI Ninja 150RR, KAWASAKI Ninja 150RR
I finally found it, but...
The Disc Rotor in NORMAL is too small and the pad does not hit the entire surface.
Large Disc Rotor must be replaced.
View detail
ZX-6R Fitment
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX636
Fitment Issue
About quality and texture : Machine work is nice with a good appearance About the feeling of use: N/A Products to buy together N/A Difficulty of installation : This does not fit the a 2019-2023 ZX-6R. This unit has multiple problems, the axle diameter is oversized at 27mm, rather then 25mm required for the ZX-6R. The anti-rotation arm to engage the swingarm lug is incorrect. If you align it centered on the axle, then the arm in angled up rather than being horizontal with the lug which will not allow movement backward and forward. If aligned on the lug, then the axle hole approx 10mm higher than it should be and about 5mm to far back. Cost performance and comparison with other products About shipping and packaging: Good Any concerns, cautions, or advice when purchasing: Don't purchase!!! Wasted money. View detail
Fits: HONDA CBR600RR
Complete design error
I installed the pad on a '07 model, but due to an obvious design error, the mount position of the brembocncCrab caliper is 5mm outward gap compared to the OEM disc diameter of 220mm, and the pad protrudes when installed as is.
The disc diameter of 230mm is not so common, and the only way is to shave 5mm off the disc contact surface of the pad and forcibly fit the pad to the disc.
There is no Caliper center, and the center must be adjusted by placing a Shim between the Mount section.
At any rate, it is not a Level product that can be sold.
View detail
ZX636-2019 Rear caliper support
Mounted on ZX6R-2022
First of all, the diameter of the Axle Shaft is completely different! The angle of the Swing ArmCaliperStopper is too large for the Axle Shaft to fit through.
I managed to install it, but the Brake Pads were about 1cm outside the surface of the Rotor ….
Dangerous because it is a Brake round!
View detail
Fits: HONDA Rebel 500, HONDA Rebel 300, HONDA Rebel 500, HONDA Rebel 300
For REBEL 250.
OverRACING is expensive, so I bought this one.
The 250 can be installed and used without any problem.
View detail
Fits: KAWASAKI Ninja 650, KAWASAKI Z650
NINJA650 Brake Caliper Support
The Caliper supportBody is of high quality and the Black Anodized looks tight and parenthesis is good. If the Bolts were also available, it would be a perfect score, but there is a time-consuming task to arrange the Bolts. View detail
Fits: KAWASAKI NINJA 250
Mounted on EX250L
It is for the current NINJA, but the thickness is 7mm different from the previous EX250L (1pc.) and OEM, but it went on relatively easily.
I have only done a 40km test run around town with the old Crab installed, but there doesn't seem to be any problems.
I think the thickness increases the strength of the product.
Things are good.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R
Low price, but not bad.
Brake PadsThe outer circumference needs to be shaved a little less than 2mm, but much better than OVER's 4mm.
The construction is more delicate than the OVER ones, but there seems to be no problem.
View detail
Fits: HONDA Rebel 500, HONDA Rebel 300, HONDA Rebel 500, HONDA Rebel 300
ABS error.
I bought it from a private importer before WEBIKE handled it.
The ABSSensor warning light always comes on around the 100 km/h mark.
It seems that the ABSSensor mounting position is gapped enough to be visually confirmed.
I ended up replacing it with OverRACING's (or rather waiting for it because I was on a production waiting list and couldn't get it) and the problem went away.
View detail
Fits: YAMAHA YZF-R15, YAMAHA XABRE, YAMAHA XSR155, YAMAHA V-IXION R155, YAMAHA MT-15
This is for 320mm Rotor.
It was for 320mm, but the Rotor I chose interfered with the Caliper. I had to shave off the part where it hit.
To begin with, the XSR155 Big rotor is not available without importing it, so you need to be prepared for a lot of things.
The details are on YouTube. We hope you find it useful.
https://youtu.be/myATZbuZZe8
View detail
Fits: KAWASAKI Ninja250, KAWASAKI Z250, KAWASAKI Ninja 250R
WR3RearCaliper-support and bremboCaliper
The brembo Crab type was purchased from Webike and installed by STRIKER in Tsuki Ward, Yokohama City. The length of the brake hose was carefully considered and the installation was very beautiful. brembo and WR3 are very compatible. Please be careful when selecting the length of the brake hose. View detail
Fits: YAMAHA YZF-R15, YAMAHA YZF-R15, YAMAHA XSR155, YAMAHA MT-15, YAMAHA XABRE, YAMAHA V-IXION R155, YAMAHA XSR155, YAMAHA MT-15, YAMAHA XABRE, YAMAHA V-IXION R155
Mr. BigRotor? Missing?
When actually installed, the Brake Pads are not aligned enough to hit the Brake rotor.
If it was a BigRotor, it would work, but did I receive the wrong one for the BigRotor? I bought a brembo compatible Caliper from another place and it was useless.
View detail
Fits: KAWASAKI Ninja250, KAWASAKI Z250, KAWASAKI Ninja250R
Brembo crab caliperSupport
I was able to install it on my ninja250R without any problems. View detail
WR3 Bracket for ZX14R
I have been wanting to do a Brembo rear caliper conversion on my 2021 ZX14R for sometime now, problem was I couldn't find a company that made the conversion bracket for the caliper, I came across the WR3 bracket on Webike Japan and ordered it, it arrived in a few days to Australia, the workmanship and quality of the product is beautiful and the fit was straight forward with no problems at all, I highly recommend this product from Webike Japan. Steve Australia View detail
Fits: HONDA CBR600RR
Defective product. It was a design error. I can't believe you put this product out into the world.
Defective product. It was a design error. I can't believe you put this product out into the world.
First of all, the height of the screw receptacle for the ABS speed sensor does not match the OEM. I had to prepare a 5mm collar by myself to install it.
Also, when I tighten up the shaft to the specified torque, I can hear the set screw of the blanket and the speed sensor pulsar rubbing against each other. The OEM blanket has a 1mm protrusion on the wheel side, but this product has a flat wheel side, so I think the height is not enough.
View detail