![icon-webike.png](https://thimg-afcc.kxcdn.com/@wth-shop/assets/desktop/img/icon-webike.png)
Reviews
![Stainless Cotter Pin Set](https://img.webike-cdn.net/catalogue/12173/0900-995-80000_TS.jpg)
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
![Stainless Steel Beta Pin](https://img.webike-cdn.net/catalogue/13652/995-0700005_TS.jpg)
Used for Brembo caliper
I purchased the Beta pin for Caliper's Pad pin because it had run out at some point.
It was cheap and saved me a lot of money. I will be Wiring it just in case.
View detail
![Stainless Steel Cotter Pin](https://img.webike-cdn.net/catalogue/11305/995-0800025_TS.jpg)
If you don't put it on, you'll be scared.
On the front tireShaft of the CUB
When Tire was replaced,
I didn't have a Pin on hand, so I ran for a while without a Pin on.
The front tire started to wobble and
When I stopped to inspect, I found that the shaft nut was loose enough to rotate with my finger.
Scary…orz
So I immediately bought it and stopped Pinning!
I honestly don't know about things.
Since it is Stainless Steel, it will have a certain degree of strength with little rust.
I think you can rest assured.
View detail
![Stainless Steel Cotter Pin](https://img.webike-cdn.net/catalogue/11305/995-0800025_TS.jpg)
Easier than buying OEM Parts?
Quantity rather than buying OEM Parts:1 Set of 10pcs. of this product may be useful in your tool box.
This time it was a little long and I should have cut the tip off, but it seemed to have no effect, so I rounded it off and used it (laughs).
View detail
![Stainless Cotter Pin Set](https://img.webike-cdn.net/catalogue/12173/0900-995-80000_TS.jpg)
Material:Stainless SteelSplit Pin
I needed a Split Pin for cleaning a Caliper on a CB1300.
This Split Pin is Stainless Steel, so I think it is rust resistant. It is not reusable, but Material:I think Stainless Steel is good. Also, if you don't know the Size, it is helpful because it contains several different Sizes.
View detail
![Stainless Cotter Pin Set](https://img.webike-cdn.net/catalogue/12173/0900-995-80000_TS.jpg)
Spare Parts
It is safe to have it in Spare Parts. View detail
![Stainless Steel Cotter Pin](https://img.webike-cdn.net/catalogue/13652/995-0800016_TS.jpg)
Is good
Quantity:1 Set of 10pcs. so I keep it in stock and use it when I need it.
It should always be Stocked as it is consumed during maintenance.
In principle, once removed, they cannot be reused, so it is better to keep a lot of Stock and replace them.
View detail
![Stainless Steel Beta Pin](https://img.webike-cdn.net/catalogue/11305/995-0700006_TS.jpg)
Size of 14
I put it on the front tire of my Ninja 250 '14 and it is Exactly. View detail
![Stainless Cotter Pin Set](https://img.webike-cdn.net/catalogue/12173/0900-995-80000_TS.jpg)
When you're short on Pin!
It is a split Pin.
It was a pain in the ass to ask for OEM, so I just bought it randomly.
Because I lost the allotment Pin of the footpeg of CB400SF for Passenger, I use it instead.
View detail
![Split Pin 4 X 35mm](https://img.webike-cdn.net/catalogue/images/73267/SCP-4035_TS.jpg)
It's a standard product.
It is very normal to use.
You can get them at the Home center, but it is better to order them while you are buying something else.
View detail
![Stainless Steel R Pin For Rear / Axle Shaft](https://img.webike-cdn.net/catalogue/images/30302/0987_1_TS.jpg)
Fits: HONDA CB350, HONDA CB750 Fore (CB750K), HONDA CB400 Fore (air-cooled)
![jp](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/jp.gif)
Split PinTune
I replaced the steel Split Pin with a workable Split Pin in Stainless Steel and it looks great! View detail
![Stainless Steel Cotter Pin](https://img.webike-cdn.net/catalogue/13652/995-0800016_TS.jpg)
It is useful for Stock.
Quantity:1 Set of 10pcs. is a good amount to keep in stock for maintenance. Once removed, it is not difficult to reuse, but it is used for the Castle Nut, which must not be loosened, so I always put a new one in. View detail
![Split Pin 4 X 35mm](https://img.webike-cdn.net/catalogue/images/73267/SCP-4035_TS.jpg)
No problem
I was too lazy to go to Homesen, so I'm here ….
It's not a thing to imply, but … it's usually usable.
It's a little stiff.
It's not a great costumer, but considering the hassle of going to buy it, … I guess.
View detail
![Stainless Steel R Pin For Rear / Axle Shaft](https://global.webike-cdn.net/images/reviews/921/00001004921L.jpg)
Fits: HONDA CB350, HONDA CB750 Fore (CB750K), HONDA CB400 Fore (air-cooled)
![fr](https://thimg-afcc.kxcdn.com/@wth-shop/image/flags/fr.gif)
review cb400f BRC Stainless Steel R Pin for Rear/Axle Shaft
Perfect! in accordance with the description, much more practical than the original system with the security, thanks webike View detail
![Split Pin 4 X 35mm](https://img.webike-cdn.net/catalogue/images/73267/SCP-4035_TS.jpg)
I bought it because it was cheaper than OEM
I used it for Rear Axle Nut of W650.
Because it is cheaper than OEM, even if you change every tension adjustment of Chain Large as durable, Quantity : 1 Set of 10pcs. I bought.
It can be used without any inferiority even if things are compared with OEM.
View detail
![Stainless Steel Beta Pin](https://img.webike-cdn.net/catalogue/11305/995-0700006_TS.jpg)
Captive
I exchanged folding pin to Beta pin for prevention of Axle Nut of BENLY 50. I think that it will be used several times, so it is Eco. But I only used 2, so I did not need it like this. View detail
![Stainless Steel Beta Pin](https://global.webike-cdn.net/photo/article/26/1372724546526L.jpg)
It is a ten-piece Pack of the Stainless beta pin of phi 6. It uses in my place, exchanging for the Rear brake drum of a SUPER CUB 110, and the split pin of a Torque-rod conclusion Nut. Although examination is also required in the place which is made
It is a ten-piece Pack of the Stainless beta pin of phi 6.
It uses in my place, exchanging for the Rear brake drum of a SUPER CUB 110, and the split pin of a Torque-rod conclusion Nut.
Although examination is also required in the place which is made into the Shaft and food on a skewer, and is used by the baffle of a Crown Nut, it can only use for the use of the prevention from omission of a Nut in comfort like a photograph.
View detail
![Stainless Steel Cotter Pin](https://img.webike-cdn.net/catalogue/11305/995-0800025_TS.jpg)
It was used on the occasion of Tension adjustment of a Chain. Since it is not used abundantly so much, a ten-set Pack is right just.
It was used on the occasion of Tension adjustment of a Chain.
Since it is not used abundantly so much, a ten-set Pack is right just.
View detail
![Stainless Cotter Pin Set](https://global.webike-cdn.net/photo/article/98/1352594853498L.jpg)
It was made the wind which it sandwiches with a vise, punctures with an electric drill, is bending through a Stainless cotter pin, and is carrying out the slack stop with iron since the Bolt of the circumference of a Rear brake was a raw material which ca
It was made the wind which it sandwiches with a vise, punctures with an electric drill, is bending through a Stainless cotter pin, and is carrying out the slack stop with iron since the Bolt of the circumference of a Rear brake was a raw material which can do drilling easily! ♪ with which it does not rust but even Kon is shining since it is the
STAINLESS STEEL
View detail
![Stainless Steel Cotter Pin](https://global.webike-cdn.net/photo/article/35/1222726501335L.jpg)
A cotter pin is a split pin. I am using the use part here of a big split pin for the axle shaft of a rear side. As it is in a picture, it is not suitable for re-use in the split pin used once. For example, Tyre exchange. In the case of a m
A cotter pin is a split pin.
I am using the use part here of a big split pin for the axle shaft of a rear side.
As it is in a picture, it is not suitable for re-use in the split pin used once.
For example, Tyre exchange.
In the case of a motorcycle, the Tyre wear of RIA is more remarkable than a front.
When exchanging rear Tyre, the axle shaft of a rear side is desorbed.
There is a nut which ties the axle shaft of this rear side.
This nut loosens and it is using the split pin for a stop.
The size of the split pin in W650 is set to 4.0x35.
Split pin exchange is carried out also except the Tyre exchange.
It will loosen the nut of the axle shaft of a rear side in the case of chain adjustment.
A split pin will be naturally pulled out in that case.
A split pin is pulled out, a nut is loosened, a rear wheel is moved back, and the tension of a chain is adjusted.
These acts are only performed and two split pins are used.
Also when carrying out chain exchange, of course, split pins may be exchanged and you are exchanged at the time of a great car wash.
even if it is alike and uses any, although one set of sale is carried out by ten, I will completely have the product here and it will describe to the sentence end that it is not set sale by a superfluous number.
Just small components support sense of security also like Rider's feelings also for a motorcycle.
It is like [ if a simile is carried out, however highly efficient Tyre will be worn, but ] un-equipping a wheel with an air valve cap.
Also in order [ which you search for ] to have you play a role safe, having small components made differs in the sense of stability of a feeling.
As for the cotter pin of an original manufacturer's product, although it is iron, it made from a kitaco is a product made from a stainless strong against corrosion harder than iron.
recommendation goods -- rather than -- the goods which should be bought are just accessories of a cotter pin or a beta pin -- ~!!
View detail