Reviews
very good product
This is a very good product. It blocks quite a bit of wind.
The design also matches the bike very well.
It's not easy to install, but it's sturdy.
If you are installing a damper, you need to think a little bit more. Since the installation locations overlap, you may have to give up one thing. -------------------------------------------------- -------- This is a very good product. It blocks quite a bit of wind. The design also matches the bike very well. It's not easy to install, but it's sturdy. Those who want to install a damper need to think a little bit more. Since the installation locations overlap, you may have to give up one thing. Powered by Google Translator
View detail
POSH Aluminum Pillion Belt Cover
About quality and texture Well made aluminum from POSH. The cover gives a beautiful outlook compared to the stock sliver look. About the feeling of use It's a cover that fit perfectly without any lapse in space. Difficulty of installation Less than 15 mins to remove the original screw and place the cover on with the given screws. I hand tighten the the screws as hard as possible. Cost performance and comparison with other products There's no comparison with others as there isn't any similar product around. The price is not expensive but it gives an additional look in your plain looking seat. About shipping and packaging Shipping is not expensive as the the items are small. Items are place in a vinyl plastic bag but no visible damage after shipping. Any concerns, cautions, or advice when purchasing The given screws length is long enough as there's worries about the safety of the belt if the pillon is to grab it. Make sure it's well tightened and theses should not be a problem. View detail
It's easy to install and the size is just right.
Easy to mount, just the right size and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. It's easy and the size is just right -------------------------------------------- -------------- Easy to mount, just the right size and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. Easy to mount, just right and good. It's easy and the size is just right. Powered by Google Translator View detail
Beautiful product
Zero gravity good quality sticker. Beautiful product. I received good packing and perfect product from webike. Thank you we bike. View detail
Fits: HONDA FUSION [Fusion]., HONDA FUSION [Fusion].
Absolutely recommended item!
Quality and Design. Excellent manufacture to customize your Honda in 2 minutes. Safe and fat shipping! I just love it !!! View detail
Fantastic
Super easy to apply with the sperately sold tool. Just follow(translate) the instructions & away you go. Make sure the rim is clean & that you spray each segment of rim with water immediately prior to applying the sticker. Be sure to work out any air bubbles etc from the application process. If it's not sitting correctly-immediately peel back and start that section again before the adhesive begins to bond. It also helps to use a hairdryer on each section after application. The mirror finish really pops, especially at night if light reflects off it at an agreeable angle. View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
This is the overall satisfaction level for ass pain measures
Since I bought a z900rs, I have been worried about the ass pain that everyone else is suffering from,
I have been studying all over the Net and watching YouTube.
There were many candidates, but we chose DOREMI for quality, cost performance, and delivery time.
The product was out of stock due to its popularity, but thanks to the power of Large Hand Wafer Big, we were notified that the product would be in stock soon and it was delivered.
The Tandem seatBelt requires a hole to be made by myself, and although I was nervous, I was able to make the hole without difficulty,
Belt could also be attached, although it is a little stiff.
I usually get an ass ache as soon as I go touring,
I felt that it was considerably eased.
Footing is a little worse, but not a problem at all in exchange for butt pain.
I would highly recommend it to anyone who is unsure about Seat from another company.
The quality is as good as OEM is also recommendation.
View detail
Pre-cut and inexpensive
I usually buy rubber mats and cut them, but this product is pre-cut and at this price, so there is no extra hassle.
Grip is also good.
View detail
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
It is definitely better than OEM.
I just took it off and put it back on, and so far it hasn't come loose, but if you're worried about it, you need to get it back on.
It looks good, but the price is too high,
View detail
Fits: SUZUKI SV650 N, SUZUKI DL 650 XT V-Strom, SUZUKI DL 650 V-Strom
The CP is also good.
From the name PyramidPlastic, I was prepared to order some more cheap products.
In fact, the FRPParts arrived with a high degree of precision, which is quite high for exterior Parts from overseas.
The bracket engages the Crankcase Bolt firmly, and the engagement with the FRP part is not bad.
However, the supplied Bolt is a bit short, so you may want to prepare a Bolt of about +5mm.
It is not impossible to stick to FRP, but it does not put a load on FRP, and above all, it increases work efficiency by a large margin.
In fact, a separately purchased DesignBolt was used for installation.
I have the impression that it took quite a long time, but it is because it is an overseas parts.
Considering that the FRP parts are solid and cost only 20,000 yen, the cost performance is also good.
View detail
impossible
When I received the package and checked it immediately, I found that the Package had already been opened and the product itself was not in the package.
Why is this not noticed when packing?
I have used many different mail order services, but this is the first time I have seen such sloppiness and I feel bad.
I don't want to give even one star.
View detail
Carbon
Scratches on the Black colored Tank are inevitable, so install it before it gets worse.
It is easy to apply with double-sided tape.
The seam between the Tank and Seat is also rounded off so that it does not look out of place.
However, the part without Tape is creaking" when pressed, so it might be better to add more Tape.
Some edges are not able to follow the subtle curvature of the tank, but I don't mind.
View detail
Fits: KAWASAKI GPZ900R
extremely sturdy
OEM Resin Bracket, only has a squishy feel.
Since the Tail lens unit is suspended and secured to the Seat rail from the underside, it can be forgiven for being a bit squishy.
This was already starting to ripple even before it was a few years old. It's like an apologetic Cover.
The aluminum plate is now anodized black, making it sturdier and sharper.
Now we are at ease.
View detail
Fits: Others , HONDA 400X, HONDA ADV150, HONDA CB1000, HONDA CB1000, HONDA CB1000SF, HONDA CB1100, HONDA CB1100, HONDA CB1100CA, HONDA CB1100NA, HONDA CB1100SF, HONDA CB1100SF, HONDA CB1300SUPERFOUR, HONDA CB250F, HONDA CB250R, HONDA CB250R, HONDA CB300F, HONDA CB300F, HONDA CB300F, HONDA CB300R
License Plate Base
Installed on a '24 GSX1300R HAYABUSA 。 It was Exactly without interfering with YOSHIMURA's Fender lessKit. View detail
Repair Parts is too expensive.
Purchase at the same time as the vehicle with the Option of a new car
I ordered Repair Parts the other day because I had a scratch from a standing accident.
You pick up a box of parts at the store and open it at home.
ProtectorBody was not included.
I contacted the store and they said that the included parts were correct.
The price is 15,000 and includes only silver-colored ornaments, bracket, and bolt nut.
Moreover, it is One Side.
It was a terrible experience and I am sharing it here.
Other than that, both OEM Engine Guard and Side Protector are attached.
In a standing strike, the Side Protector was grounded first and the Engine Guard was not scratched.
View detail
Repair Parts' pricing is bad.
Purchase at the same time as the vehicle with the Option of a new car
I ordered Repair Parts the other day because I had a scratch from a standing accident.
One Side with 15,000. That's expensive." I thought that Y's Gear products would be safe, so I bought it.
You pick up a box of parts at the store and open it at home.
Included was a Silver colored decorative Cover, flat Bracket, Bolt, and Color!
ProtectorBody was not included.
Huh?" I asked the store about it, but they said that the included parts were correct.
Please be careful.
This product looks good, but its Repair Parts are a rip-off, as if to undercut people who have had accidents.
The price is 15,000 and includes only Silver colored ornaments and Bracket.
Moreover, it is One Side.
It was a terrible experience that made me so angry that I felt I would never buy Y's Gear products again, so I will share it here.
Other than that, both OEM Engine Guard and Side Protector are attached.
In a standing strike, the Side Protector was grounded first and the Engine Guard was not scratched.
View detail
Fits: HONDA CB400SF VTEC, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR REVO, HONDA CB400SF VTEC REVO
Mounted on NC39
I am satisfied with the OEM color, so there is no sense of discomfort after installation.
Since the paint can be scratched off by stepping stones while driving, it is a good idea to put a protection film or the like on the front end of the car so that you can go touring with peace of mind.
View detail
_TS.jpg)
Recommendation for those who want Rear under cowl on GSX-8S,8R
Although it is an overseas product, the precision and quality are high, as if it were a manufacturer of for-race parts.
The GSX-8S and 8R have only a thin rubber plate as a partition between the tire and the rear suspension, so if you are concerned about splashing mud on rainy days or dirt on the rear suspension, this is a recommendation.
The shape is also cool, with an accent near the center, and the Matte Black color gives a sense of uniformity, as if it had originally come from the OEM.
View detail
Circuit support
I bought it to run Circuit with MOTARD.
Gasoline spillage can be prevented in the event of a fall.
The aluminum bubbles are anodized and well designed.
View detail
Grip is good
Grip is good and can be held properly.
Double-sided tape does not have a bad bite, but the resin part tends to peel off easily due to temperature changes, etc., even if the tape is degreased properly.:When applying to Unpainted resin, it is better to use strong Double-sided Tape for Vehicleetc.
The Cut surface is standing up and may catch on the seams of the Pants. I used Cutter to cut off the corners.
View detail