Reviews
Ideal for lightweight
Installed on 8BK-RG74J.
No loss of horsepower with regulated engines = can be converted by replacing the Exhaust System. but there was not much change at the JMCA, where the regulations are tighter.
In the 250cc class, the Large body only varies by 1 to 2 horsepower no matter which Exhaust System is selected, so this Exhaust System is recommended for weight reduction purposes.
As for the sound, the 8BK is almost 90db OEM, so you hardly notice any change in volume, but some parts have a thicker sound depending on the RPM.
In terms of sound quality, I think you would feel more change with Planus or WR's Slip-on Silencer.
The quality, however, the accuracy of the front pipe was quite poor, and it did not fit neither the Engine nor the Center pipe, so it had to be installed while bending it with Lever.
Although less expensive than other Full Exhaust Systems, it would have been nice to have a more accurate product.
When installing the Silencer, it is recommended to temporarily fix the Exhaust Band and Bracket and then install the Bracket on the body of the vehicle, as it is quite difficult to install the Exhaust Band if you follow the Instruction Manual.
Also, although not mentioned in the Instruction Manual, it was necessary to change the Wiring position of the O2 Sensor.
The OEM position is fixed in front of the Clutch cover, but once removed and placed through the rear.
Although it has a few drawbacks, it does not look like other people's and can be lightened to a large width, so I think it is recommended for people who are visually oriented.
View detail
Fits: YAMAHA WR155R
WR155R Full Exhaust System Comparison
I have tried three Full Exhaust System, PROLinerXR-1⇒DAYTONA(IndonesiaYamahaOption)⇒Yoshimura cyclone. As for the comparison of the three systems, my personal opinion is that overall they are 1st DAYTONA (IndonesiaYamahaOption), 2nd Yoshimura cyclone and 3rd XR-1. They all have their pros and cons...
XR-1 is really noisy enough to break your ears in Tunnel, and when VVA starts to work, it stalls (Gas is too thin), so it is obvious that Injection controller and fuel condition are necessary. YOSHIMURA's total balance is excellent and he is able to drive on public roads with confidence, and he is able to secure satisfactory torque and power from top to bottom. Lastly, DAYTONA is my favorite with YOSHIMURA's fee ring with higher volume. Also, it is the only one with a baffle, which allows for simple sound deadening, and the exhaust pipe is the longest of the three, which seems to secure the Torque. The difficulty level of installation is the same for all 3 Rings. However, only YOSHIMURA's Fender Eliminator has a blinker that interferes with the pipe, so it needs to be relocated. In addition, the Gasket of the middle pipe is required.
View detail
Fits: YAMAHA WR155R
WR155R Full Exhaust System Comparison
I had been using the inexpensive PROLinerXR-1, but it was so loud that I thought my ears would break if I used a tunnel, etc., and the silencer was cut, welded, cut, or jointed with the middle pipe in one piece. The volume is quieter than the XR-1 with the attached baffle, but I think it is in the Large category. However, with the inner baffle attached, it is easy to muffle the sound. In addition, the XR-1 stalls around 7000 rpm when the VVA starts to take effect, and the gas is obviously thin, but there is no such phenomenon and the engine runs smoothly and powerfully from top to bottom without any stress. The price is comparatively inexpensive, and we recommend this product to those who can endure until it arrives in stock. View detail
Style& sound is perfect!
I bought a CROSS CUB instead of a CT110 HUNTER CUB to install the CABTON Exhaust System!
It looks great, just as we wanted it to.
Sound is also light.
View detail
Exhaust System first replacement
I ordered this for my CA45A LETS4 because I had a cracked Pipe at the root. Tighten the Bolt and tighten the back Quantity:The 2pc holes were Bolt in while pushing and pressing the Exhaust SystemBody to align the holes.
The noise of the Exhaust System is quieter than before the previous OEM Exhaust System was broken, so it can be used on public roads and residential areas without any problems.
View detail
Short Tube Installation
Previously used Exhaust System with aluminum silencer.
The Torque is thinner overall due to the short tube, and I have the feeling that the engine rotation is lighter instead.
View detail
Fits: KAWASAKI ZZR1100 C type D type, KAWASAKI ZZR1100 C type D type
Perfect fit
This exhaust is beautifully made, the lightness of the titanium and carbon is exquisite, The fit is so perfect and it allows access to the oil filter for service and you can keep the centre stand. I'm delighted with it, my ZZR rebuild is complemented by this excellent exhaust, The carbon cans match my carbon Dymag wheels perfectly. View detail
Misty Kan
Looks and sounds great.
I was very happy with the delivery date, which was about 3 months early!
View detail
bass
Mounted on GORILLA.
A heat guard can also be attached to the GORILLA by fixing it to the stay on the rear side with a bolt that matches the 1cm collar.
The bass is most pleasant.
View detail
Good design, sound and build.
[How is it used?
・Touring (Almost Winding)
Was the one you received as per Image?
The texture was just as wonderful as it looked in the pictures.
The welding of each part is also beautiful.
Was the installation difficult?
The dimensional accuracy of each part is excellent, and if you read the instruction manual, you can install without any deviations. (I think it is more difficult to install than Up type in terms of work space.)
We recommend that you check the torque of each part in the separate service manual for installation.
How was your experience with it?
Not only is the Design great, but it plays a motivating Sound!
I think the volume is just right.
There is a sense of increased acceleration compared to OEM, and no drop in low-speed Torque.
Items that should be purchased together
Exhaust Gasket should be purchased separately and replaced with a new one.
View detail
For Scooter commuters to enjoy
The lower part of the muffler is lost from the Normal muffler, but I felt a stretch in the middle to the middle that is not present in the Normal muffler.
By replacing the Weight Roller, we were able to ride comfortably in city use.
The maximum speed is also quite good (laughs).
View detail
Fits: SUZUKI V-STROM250SX, SUZUKI GIXXER250, SUZUKI GIXXER SF250
The old MODEL should have been good, but the new MODEL is also quite good!
YOSHIMURAR77S mounted on vstr 250sx
I really wanted the old model design, but they didn't have it in stock, so I bought the new one.
My impression when I put it on was Sound, which reminded me of the YOSHIMURA I wore in my youth.
It is a single cylinder Motorcycle, so I am satisfied with the thumping feeling.
I am glad that the design matched the car body when it was installed.
The improvement in power can be felt very much at 5.6000 rpm in the middle speed range!
Demerit, when starting, especially with a tandem or a lot of luggage on board, I felt that the start was slower than in NORMAL.
The other thing is that After Fire is now missing more, so it happens when Downshift or when I move Access back.
Well, After Fire occurs even in NORMAL, but it's hard to hear because of the sound deadening wall, so it's not a particularly large problem.
I feel that with Carburetor Vehicles, I can reduce the amount of fuel by thickening the fuel a little....
The only other thing is that the Installation Manual was a little difficult to understand in some parts.
The rest of the details will be available on YouTube.
View detail
Great
The packaging is meticulous.
Installation is easy, requiring only a hang to peel off the old Gasket.
After the installation, a test run showed that the Torque is increased in the entire area.
It makes you want to turn it. I will turn it.
However, it is a little noisy when the Axel is opened to a large size.
When opened modestly, it accelerates reasonably well and is quiet.
Although these are expensive parts, they are carefully crafted, and you will feel a sense of ownership.
View detail
Fits: HONDA GROM
enchanting (Lol)
It was the first time I tried to replace the Exhaust System by myself, but I managed to complete it.
The Style has tightened up a lot!
I just couldn't get ECUReset to work. ( Nope.) Siksik…⇒ I'll have it looked at at my next inspection.
The sound in general was LARGER than I had imagined.
We live in a residential area, so we have to be careful about the sound of iDrink (especially in winter).
Sound is satisfied.
View detail
Appeal to appearance and surroundings (As a safety measure)
The sound will be a nice Appeal (laughs).
I used MORIWAKI muffler on my previous LEAD125 and I like the sound, look and feel.
If you expect it to run well, you can replace the Weight Roller at the same time for a good driving experience!
View detail
Fits: HONDA REBEL1100, HONDA REBEL1100, HONDA REBEL1100T, HONDA REBEL1100T
MORIWAKI Complete exhaust CROSS TWIN BLACK
Finally after a year of questions and doubts I purchased the MIORAKI muffler which for me is a marvel, a beautiful product with a deep sound compared to the original and above all aesthetics, what can I say I really like it, I recommend the manufacturer and the seller to all serious people who know what to do their work is very good. THANK YOU SO MUCH MIORAKI THANK YOU SO MUCH WEBIKE JAPAN ------------------------------------------- --------------- Finally after a year of questions and doubts I purchased the MIORAKI muffler which for me is a marvel, a beautiful product with a deep sound compared to the original and above all aesthetics , what can I say I really like it, I recommend the manufacturer and the seller to all serious people who know what to do their work is very good. THANK YOU SO MUCH MIORAKI THANK YOU SO MUCH WEBIKE JAPAN Powered by Google Translator View detail
Fits: KAWASAKI ESTRELLA
Exchange from OEM
Lighter than OEM and refreshing in appearance.
I think it's cool.
View detail
Fits: YAMAHA CYGNUS Gryphus, YAMAHA NMAX
quintessential SP Tadao
It is a well-known Manufacturer, so the construction is solid and no additional work is required at all. View detail
Fits: KAWASAKI W650, KAWASAKI W400
Lack of Clearance?
I bought it because I like the way it looks. 。 It was a replacement from OEM Exhaust System, and I am satisfied with the sound of 2 cylinders. 。 Bolt to fix Silencer, Nut is Quantity:Pair (for Left and Right) I found it confusing because it is different in View detail
Mounted on CROSSCUB110 JA60
My favorite is the color Black and the heavy bass sound.
Power is also up!
View detail