Reviews
I can really help. It is safe and secure.
It is safe because Hook does not move.
We recommend that you take a look at Jtrip's Channel on YouTube for a video showing how to use it.
Work is safe and secure.
View detail
Wouldn't this be the perfect maintenanceSTAND for Middle motorcycle!
I am satisfied with the stability of the vehicle when using the rear stand, the lightness when lifting up, and the price. I was thinking of replacing the tires by myself in the future, and I am also hoping to expand the range of maintenance of other parts. (The Z650RS weighs 188kg *Rear Carrier would be better) It only requires a little weight by hand. It is very convenient because I used to do one side lift up with a piece of wood.
Comparisons were made with Company S, Company A, and Company J. As a result, we decided on DAYTONA. As the reason for the selection, I considered that the structure of the most load-bearing part is Square Type, which seems to be sturdy, and that it is superior in terms of comparative cost. Also, the fact that the product introduction image is of RS was a deciding factor. The other 3 companies are all sold separately, and S and A are a little cheaper than DAYTONA, but there were some comments that the stability of the frame is not so good. I have not actually used them, so I am not sure.
The Stand Hook holder is specified to have a diameter of 14 to 18mm. If the diameter is larger than this, it will not fit in the attachment. Also, it takes a little getting used to inserting the Attachment.
The only drawback is that the latch of the U-shaped attachment is too thin and I am not sure if it is durable. I am not sure if it is durable or not. I don't know because I haven't used it yet. However, spare parts are available, so there is no need to worry. (This is not a problem for those who can weld.)
J company claimed that the handlebar should be set to "Left" and "Up" when the brake is "STAND-UP", while DAYTONA company claimed that the handlebar should be set to "Straight". I am not sure of the difference, but I found that the fixation of the hook of the front brake at the time of OthersLift up was the same in all companies. I hope this is of some help.
View detail
Almost perfect except for the price.
The front and rear stands seem to be the best in a certain manufacturer, but this product is sufficient for cleaning and simple maintenance at the Amateur level.
However, the price could be lower, so the rating was not a perfect score.
View detail
DAYTONAfor Repair
I bought this one because I cry when I drop it.
Used for thruxtonrs.
The oval-shaped swing arm has a shallow hook.
If this is not possible, use a Y-shape.
View detail
useless
Purchased for Spoke maintenance. Conclusion:It can't be used. First of all, I can't use it with Harley because I can't get over the bumps. It was faster to use Jack. View detail
Daytona spool nut
Fits perfectly! View detail
I am glad that there is a Repair item since the item will deteriorate!
I bought for Repair because it has been ripped over time and the Rubber at the tip of the V-receptacle has been coming off every time I apply STAND.
I am glad that there is a Repair item, as these items deteriorate.
Double-sided tape makes it harder to pull out." I also put up Double-sided Tape because of the proviso that it was a good idea.
Since it is Rubber, deterioration is inevitable.
Hopefully this won't take...
View detail
I bought it by model.
The size of the part that goes into the Head did not fit and could not be worked. I will probably process it and use it in the future, but I was a little disappointed. View detail
Reliable Brand
Purchased due to the addition of a Large Motorcycle.
We use Chinese STAND for 125 and 400 Class Motorcycles and this one for Large Motorcycles.
With Chinese STAND, the STANDBODY is distorted by the weight of the car body when it is lifted up, but this product can be lifted up stably without any problem at all.
If I had to make a request, I would say that protective parts should be attached to the pipe that touches the ground when lifting up, otherwise the STAND will become wound wound.
View detail
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
Easy to use
I purchased the Round Type because my ST250 has a circular swing arm. I am satisfied with it and can use it without any problem. View detail
Easy to use
The rear wheels can be used without difficulty, but the front wheels cannot be used. The front wheels are gradually shifting, perhaps because they are stuck in place. View detail
DRC wheel tool anti-vibration/balancer option 10mm shaft set Product # F4287
Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery Thank you for the fast delivery View detail
Allows you to turn your Motorcycle around in a comfortable position
I bought it because I wanted to enter the garage from the front of the Motorcycle and park it, then turn it around 180 degrees for the next time I exit (I wanted to keep the front of the Motorcycle facing the garage exit side).
There is a similar product, Motorcycle Moveretc., which is used to lift the rear tire by stepping on it with the foot (by the principle of leverage), but when I tried one owned by a friend, I found that this product was easier to position myself in and moved the motorcycle stably. However, since the Side Stand is dragged, I think it is necessary to use it with STANDRoller for vehicles with LargeEngine Displacement Volume. (The same applies to the Motorcycle Mover.)
In terms of price, it is less expensive than Motorcycle Mover, and the quality is not bad, so we felt that Cost performance is high.
STANDRoller is sold separately, but the Quantity:It would have been better if it was a Set sale.
View detail
Ideas products for improved serviceability!
I saw this product in DAYTONANews and bought it as soon as it went on sale.
I had a chance to do maintenance of CRF and SEROW's LINK circumference with just the right timing and used it immediately.
This tool is very easy to work with when pulling out and inserting the Axle Shaft and using it to assist in removing and installing the Wheel, as well as when slightly changing the angle of the Swing Arm for maintenance of the LINK circumference and adjusting it to a position where no excessive weight is placed on the LINK circumference.
When the Hook is hooked and pulled forward, the height of the Wheel is raised to just the right position, and the load can be set to Free, making it very easy to work with the Bolt around the LINK.
It is good to have one if you have many opportunities to service the rear wheel area.
View detail
Feeling of security
I always had a hard time hanging the Maintenance Stand on the Swing Arm, but by fixing the front tire to the ClampSTAND, the stability is increased and the Maintenance Stand can be used with ease. View detail
Sure, it's easy.
I thought I could do without it, but when I used it, it was much easier than I had imagined. View detail
Nothing beats it, as long as you have the space to put it.
I bought a battered 900SS (900SL) and am Restore.
Everything is RoseRose until Bolt1 pc, then everything is Repair and modified and regenerated before assembly.
Stem bearings and other parts were also replaced, but since they are all RoseRose, it was easy to complete the work by simply turning the FrameSingle Body over and over while hammering.
The Ducati of this era had no dust or oil seals on the stem bearings, and the sliding surfaces of the bearings were exposed in a barbaric manner.
The bearing is really exposed, and even the bearing race can be seen when peering from below at certain angles.
The large washer, which was used in later models, was inserted into the lower side of the stem shaft.
Since it is just a Washer, there is no RubberRip seal, just a little harder to see Bearing and a little less gap with the Frame.
Still, I built it in thinking it would be better than nothing...
When assembled, the Washer effect does not look very promising.
On the contrary, it appears that foreign objects that have been placed on top of the StemBracket have become even more likely to enter the Stem bearing area.
I thought so, but the body is already pretty much assembled, and I don't want to remove parts now to make a FrameSingle Body.
Then there are two ways.
Lift the front of the body in some way or lift the body Front in some way.
The most stable method is to use a Jack or other lifting device.
The weight of the car body rides directly on the hard STAND, so it can lift TIGHTLY and Front.
But it often doesn't work that way, does it?
If it is a 4-cylinder engine, the exhaust pipe is in the way 100% of the time, and even if the exhaust pipe is removed, the oil pan is not flat on modern engines.
This is where the Frame Stand comes in.
As the name implies, you can put up something like a clothes-drying stand next to the Frame and use it like a clothesline.:Pair (for Left and Right) The Tie Down is hung by hooking the Tie Down to a stick passed through the
It is suspended by a string, so it is not very stable, but it is very easy to use.
This product is a super large version of the Frame Stand.
The maximum height of 2m is not a feat!
There is no doubt that the bigger the better, and this product is also much easier to use than the 1.5-meter Frame Stand that is often used by other companies.
It is so big and heavy that it has great rigidity, even when the body is suspended. The "feel" is a little bit like a "bounce. is Zero!
It is comparable to the high-performance STAND, which is sometimes used in motorcycle shops for PRO use.
The only weakness is Super big and super heavy." Things to do!
As you can see, it is a huge large when assembled!
Then I would say disassemble it after use...but no, no, no!
It will not stand on its own when disassembled, and even when disassembled, it is still big enough!
And since it's made of steel, it will definitely be covered in Rust if left outdoors...
in a word "Location matters." But [Color] The ability to Clear is the key to success.
If you are fortunate enough to have the indoor Space to store such a Giant Large item, this is a real treat.
View detail
Rigid and easy to raise
It is rigid and easy for Arm to step on, making it easy to raise the vehicle. It is also easy to adjust the height to the vehicle by simply rotating the seat.
However, the Lockling-like thing that fixes the seat surface is supposed to be fixed by hand, so it doesn't seem to make much sense. It is quite large and sturdy, but if you want to fix the height of the seat, you may have to tighten the Ring as hard as you can.
View detail
It is strong and secure.
This type of product is unstable and dangerous unless it is strong and well made.
The price is high, but the results are inexpensive because the work can be done with peace of mind.
Strange Chinese products are dangerous and expensive if something goes wrong.
View detail