Reviews
Older cars with Cowl, note dimensions.
In the 80's and 90's Racer replicas, the Meter area was designed with a Horizontal Type MASTERCylinder, so there is a high probability that when the Handlebar is turned to the Left, the base of the Brake lever will contact the Meter, causing not only the Front brake to fail, but also the Handlebar Lock to fail, This will not only cause the front brake to be inoperative, but also disable the handlebar lock.
BrakeTouch itself is no different from the Horizontal TypeMASTERCylinder and Large, but the controllability is a little better.
After using it for a while, I may revert to Horizontal Type if it seems to offer few advantages.
View detail
Fits: YAMAHA YZF-R7
Diversion to 2020 R25
It has to be pointed slightly downward to hit the FrontOwl. However, if the hose is pointed down, it will interfere with the joint part of the brake hose. I ended up cutting off the interfering part and was able to attach the hose. View detail
Expectations for Small diameter
Many people think that changing Caliper will help.
Caliper piston and MASTER diameter must match.
Z900RS is about 70% with the new Crab, so it will not work unless it is replaced.
View detail
Fits: YAMAHA ZEAL, YAMAHA YZF-R7, YAMAHA YZF-R6, YAMAHA YZF-R1, YAMAHA XJR1300C, YAMAHA XJR1300, YAMAHA XJ400, YAMAHA TZR250, YAMAHA TZR125, YAMAHA TMAX500, YAMAHA TDR250, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRV250, YAMAHA SR500, YAMAHA SR400, YAMAHA SR400, YAMAHA RZ250, YAMAHA RD400, YAMAHA FZR250
Original Japan Daytona x Nissin 14mm axial . Took 3 days to arrive to Singapore from mailing date .
Easy bleeding during installation . Upgraded from 11mm to 14mm axial. Love the lever feels. Installed on Yamaha Vixion-R 155 . View detail
Fits: KAWASAKI Ninja ZX-25R SE KRT Edition, KAWASAKI Ninja ZX-25R SE, KAWASAKI Ninja ZX-25R, HONDA CBR250RR, YAMAHA YZF-R25
Brake's Stress is reduced.
This is a change from OEM horizontal placement 11mm to 5/8Radial master.
Because it seemed to interfere with the Switch box, the Lever was changed to Eukanaya's (NI002-049),
Nisshin's Tank Bracket (49151) for Separate Handlebars is installed.
As for the banjo fitting, a stainless steel mesh hose (AC Performance line) compatible with the car model was originally installed, but it interfered with the switch wiring, so an L-shaped adapter was used to make an escape.
My impression after installation is that the absolute braking force has not changed, but the controllability has improved.
Specifically, it is an Image with interpolated increments of braking force according to the strength of the grip.
The beginning of the grip is especially noticeable. With the horizontal 11mm pad, the rise in braking force is abrupt, but with the vertical pad, there is a sense of being able to adjust the strength of the pad. The same is true near the end of the grip, making it easier to generate strong braking force without locking.
Probably because the lever ratio and diameter are designed to match the weight of a horizontally mounted 11mm lever, it will not be that uncomfortable (too effective or too ineffective) to replace it. If you want a lighter grip or more strokes, you may want to consider a 14mm or 15mm model such as the F Land-.
In general, I can recommend it, but since it is Large strange to do banjo fitting by yourself, it is safer to ask a supply store with a Pit.
View detail
Excellent peace of mind in any situation.
[How is it used?
Was the one you received as per Image? The design is exactly as shown in the Image, compact and beautifully finished.
How was your experience with it? There are no problems with control of the braking force, and the braking force can be applied with confidence during operation while turning.
[Points to note] When installing, the compatibility with the normal parts was a bit difficult and took a bit of time.
How did it compare to other products? There was a cloud of difference from NORMAL.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Fits: YAMAHA MAJESTY250(SG03J)
MAJESTY's Brake to Quantity:Pair (for Left and Right) in exchange for
Right Side (for Front) When replacing the Master Cylinder of the Left Side, the Left Side was replaced together with the Right Side because the appearance of the Left Side in Normal is not consistent and not cool.
Unlike the OEM, the 6-step lever play adjustment is also highly satisfactory.
As with the Right Side, the OEM MASTERPiston diameter was lowered by 1 size (11mm) compared to the 1/2-inches of the OEM MASTERPiston diameter, and the brake was strengthened by the SKULL Helmet principle.
However, the Piston size of MAJESTYC's Rear caliper is smaller than that of the Front caliper, or perhaps the Left brake has a harder feel than the Right brake.
For now, I'm using the largest play size, but it's a little hard to control. (The fact that it is a Rear also makes it extra.)
Front is softer and easier to Control.
However, there are no more smallest piston diameters in this series of masters, and it is within the tolerable range, so it is used as it is.
I think it would solve the problem if the Caliper on the Rear was the same as the Front, but the cost-effectiveness is not so good, and it would cause other problems, so I'm leaving it as it is.
The Rear is also equipped with Yamaha's 83mm Pitch Caliper, so the for FrontCaliper can be attached to the Rear as well, but instead of having the same touch, the pad area increases, which increases the brake braking force of the Rear too much and causes the balance of the Rear to collapse. However, the pad area is increased, which increases the braking force of the Rear Brake too much and causes the Rear to lock easily.
View detail
Fits: YAMAHA Cygnus X SR, HONDA XR50 Motard, YAMAHA XT660X, YAMAHA TZR50, YAMAHA TT250R Raid, YAMAHA RZ125, SUZUKI volty, SUZUKI cobra, SUZUKI Across, SUZUKI VX800, SUZUKI TS200R, SUZUKI TS125R, SUZUKI DR-Z400SM, SUZUKI RMX250S, SUZUKI SV400, SUZUKI GS125, SUZUKI GS125E Katana, SUZUKI RMX250, SUZUKI GSX250S Katana, SUZUKI RG200
Good product
Fits kawasaki w800 Improved the sponginess feeling Arrived well without any problem with customs Good service Highly recommended View detail
Fits: YAMAHA YZF 450, YAMAHA YZF 400, YAMAHA YZF 426, YAMAHA YZ 250, YAMAHA WR F 250, SUZUKI RMZ 250, SUZUKI RMZ 450, KTM XCW 525, KTM XC 525, KTM XCG 525, KTM SXS F 450, KTM SXS 540, KTM SXS 250, KTM SXS 450, KTM SXC 625, KTM SX SXS 125, KTM SX 300, KTM SX F 250, KTM SX 250, KTM SX 144
I don't know.
We used Brembo for the front calipers this time.
The caliper recommendation was 15RCS, so I put it on my Grom, and the brake touch is totally different compared to the stock one.
I've been riding my CB250R and getting more and more hits, and the front brake is working better and better.
I don't feel like it's direct. Well, I've never ridden a bike with ABS before.
I knew what to expect.
It felt like the 15RCS recommended master cylinder when I gripped it.
I was tempted to put on 16RCS and compare. Sweat.
It's expensive, so I can't just change it at a moment's notice.
View detail
Clutch becomes lighter
I installed it on New Model GSX1300R HAYABUSA.
In fact, this time we are replacing VRD, also by GALE SPEED. replacing VRD to VRC from higher MODEL to Standard model may sound strange, but there are actually various reasons.
First of all, I was attracted to this VRC the moment I received it and opened the box. It looks like a work of art indeed, and just looking at it raised my Tension and made me feel that it was worth the high price.
I think it beats bremboRCS just for the smooth surface treatment. To be honest, I don't understand why brembo's RCS is so popular. I used to be a brembo RCS fan, and I used to think that no matter what kind of motorcycle I switched to, I would first replace it with brembo's RCSMASTER.
However, I felt the quality of brembo's forging was not worth the price. I was tired of that, so I chose GALE SPEED's Vine VRC this time.
Back to the story, I first went for the VRE feel and went for the bright black VRD for Cost considerations, but I quickly gave it up and went with this VRC because it looks like RCS and I felt something was wrong with it. I am usually a Touring Maine, so I can't tell the difference between VRD and VRC! Still, I chose it because of the way it looked. If that's what you enjoy, then that's fine.
Finally, after installing it and running it for a bit, it feels very good - lighter than the OEMClutch, and a little bit better at 17.5mm.
※※※※ Note ※※※※
New Model GSX1300R HAYABUSA will change the clutch master, [Hill HoldControlSystem will not be available.
The reason is that with the OEM clutch switch, if the clutch is released for a moment, the switch returns, the ECU recognizes that the car is starting, and the rear brake is released. However, with the external clutch master, the switch remains pressed until all the clutch is released, so the car is not detected as starting, the rear brake remains on, and even if the Axel is turned, the car does not move forward! This is very dangerous. I would like to see any Manufacturer solve this!
↑ It may be a little confusing, but try it yourself, it will never start!
In my case, I have turned that function off.
View detail
I'm glad I went with VRC.
I purchased this VRC when I replaced my GSX1300R HAYABUSA with a MASTER. In fact, this time, it is a replacement from VRD, also by GALE SPEED. replacing VRD to VRC from higher MODEL to Standard model may sound strange, but there are actually various reasons.
First of all, I was attracted to this VRC the moment I received it and opened the box. It looks like a work of art indeed, and just looking at it raised my Tension and made me feel that it was worth the high price.
I think it beats bremboRCS just for the smooth surface treatment. To be honest, I don't understand why brembo's RCS is so popular. I used to be a brembo RCS fan, and I used to think that no matter what kind of motorcycle I switched to, I would first replace it with brembo's RCSMASTER.
However, I felt the quality of brembo's forging was not worth the price. I was tired of that, so I chose GALE SPEED's Vine VRC this time.
Back to the story, I first went for the VRE feel and went for the bright black VRD for Cost considerations, but I quickly gave it up and went with this VRC because it looks like RCS and I felt something was wrong with it. I am usually a Touring Maine, so I can't tell the difference between VRD and VRC! Still, I had to choose based on looks.
Finally, after installing it and running it for a bit, it feels very good, I feel the VRC is sufficient, I don't really need VRD or VRE except for Race.
We recommend this VRC over RCS! You will never regret it!
View detail
Fits: YAMAHA YZF-R6, YAMAHA YZF-R1, KAWASAKI ZX 14 R, KAWASAKI ZX 10 RR, KAWASAKI H2R, KAWASAKI ZX 10 R, DUCATI 1103 V4 Panigale, APRILIA RSV4 APRC, TRIUMPH Street Triple RS 765, MV AGUSTA F4 RR 998, KTM 1290 Superduke R, MV AGUSTA F4 1000 LH 44, HONDA CBR 1000 RR SP, DUCATI X-Diavel S, DUCATI Multistrada 1200 S, DUCATI Monster 1200 S, DUCATI 1299 Panigale, DUCATI Monster 1200, DUCATI 1260 S Multistrada, DUCATI 1199 Panigale Superleggera
Compare with Yamaha Brembo
I was not dissatisfied with the performance of the Yamaha Brembo on the YZF-R7, but there was no lever available to install the REMOTE CONTROLLER, so I had no choice.
Installation, but requires Bullet Terminal processing and Nipple modification on Switch.
Since OEMWiring is a Connector, it is cut and converted to Bullet Terminal, and the RCS side is also cut and shortened.
The Nipple seemed to be able to go as it was, but the Hose needed to be bent 90° and it was too tight, so I changed it to Straight.
The nipple diameter of the RCS is 7mm, but the OEMTank is 8mm, and the RSC side is governed by the 8mmHose, so the 7mm is forcibly installed.
If you are particular, you should buy a 7mm Tank.
The Yamaha Brembo has a banjo on the side, so I used an offset adapter, but the RCS can go without it.
The Chinese $3,000 REMOTE CONTROLLER came on with no problem. The REMOTE CONTROLLER is easier to adjust even if it is not Race.
There is almost no difference in structure between the 16mm Radial Yamaha Brembo and the 17mm Radial RCS, so I don't feel any difference in performance, although the price is about twice as much.
I chose RCS for the REMOTE CONTROLLER, otherwise Yamaha Brembo would have been sufficient.
View detail
Fits: YAMAHA YZF-R7
It is a MASTER with excellent cost performance!
[How is it used?
This will be an imprementation with 100% Circuit driving.
Was the one you received as per Image?
Yes.
As shown in the photo, it arrives in a box in Assembly condition.
Was the installation difficult?
If you are able to bleed the air out of the Brake, it is an easy category.
For workability, pull out the Fluid from the Reserver tank to the banjo bolt of the MASTER.
Next, remove the banjo bolt from the OEMMASTER, and then remove and install the MASTERBody in the reverse order.
How was your experience with it?
This time, we replaced the OEM Nisshin Radial master from YZF-R1M, and the fee rings are excellent.
The piston diameter is the same (16mm), but the lever ratio is different, making it slightly stroker. This is very effective in circuit driving, and the BrakeRelease side has a lot of Strokes, which makes control easier. I think it is better than RCSMASTER of brembo. The R7OEMMASTER is 16mm, so it is theoretically more on the Stroke side. The closest thing to a replacement Brembo master is the Racing master 16x18, but since you can get one for about half the price, this master is a very cost-effective option. Moreover, since the banjo is not located on the bottom as usual but on the side, it is highly possible to use the OEM hose. In fact, again, the Banjo bolt and Hose use the OEM as is. However, one thing to note is that brembo usually has a bolt pitch of 1.00mm, but this one has a bolt pitch of 1.25mm. Therefore, if your car is equipped with the OEM Brembo master, the pitch may not match.
[Included Parts:were they on?
There is no particular Included Parts:as it arrives in Assembly condition.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Two separate banjo bolt Gaskets are required for installation.
Others are basically Bolt On. The hose from the reservoir tank to the MASTER is a transplant from the OEM Nisshin MASTER, because the length and bending angle of the R7 hose are not the same. The hose here, as well as the banjo bolt pitch, has a different diameter nipple than a normal brembo.
Finally, if you are riding a YZF-R1/M and suffering from the OEM patched fee rings, I highly recommend this MASTER. It is the most cost-effective solution for the smallest cost and the largest effect. In other words, Demerit is Zero.
View detail
Fits: KAWASAKI Z1000 (water-cooled), YAMAHA V-MAX 1680, TRIUMPH DAYTONA675, SUZUKI GSX-R600, SUZUKI GSX-R1000, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI B-KING, KAWASAKI ZX-6R, HONDA VTR1000SP, Others
Parenthesis good!
I bought it because I wanted to have the same type of Brake and Clutch. View detail
Fits: YAMAHA YZF-R7, YAMAHA YZF-R6 S, YAMAHA YZF-R1 SP, YAMAHA YZF-R1, YAMAHA YZF 1000R, YAMAHA MT-07, YAMAHA MT-09, YAMAHA FZS 1000, YAMAHA FJR 1300, YAMAHA BT 1100, YAMAHA FJR 1300, SUZUKI Hayabusa, SUZUKI GSX-R 750, SUZUKI GSX-R 600, SUZUKI GSX-R 1000 R, SUZUKI GSX-R 1000, SUZUKI GSX-R 1000, SUZUKI GSX-R 1000, MV AGUSTA F4- RR, MV AGUSTA F4- 1078
Genuine Brembo 19RCS Corsa Corta fitted to YZF-R1
The YZF-R1 came in wanting to be transitioned onto a track related bike so I went to work on the braking system. One of the first things I wanted to change was the annoying stock master cylinder. Obviously, Brembo was the way to go. I decided on this one as it fitted with the specs of the bike in mind. Finding the correct master cylinder was not hard but there were a few choices but I went for this one, the 19RCS Corsa Corta in the end. It had all the requirements I needed so it went in my basket. I had a few other parts and the shipping was reasonable for what I had. EMS got my order to me in 5 days. The master cylinder came with the standard stock lever length which was perfect for my needs. It is the 18 x 20 one so works good with the floating calipers on the bike anyway. It came in the Brembo box and also came with a few copper washers. I had already sourced the HEL line that would make this all work. The master cylinder is a real piece of kit and fitted really well with the bike and the instrument cluster I was leaving in situ. Not a hard job once you have all the parts together. This master cylinder is awesome and so much better than the stock one. Oh and by the way, looks the nuts. There are just so many adjustments that you can definitely find the right setting for your liking. Thanks Webike for the great service you provide. View detail
Fits: YAMAHA YZF-R1, YAMAHA YZF-R6, KAWASAKI ZX 14 R, KAWASAKI H2R, DUCATI 1103 V4 Panigale, TRIUMPH Street Triple RS 765, MV AGUSTA F4 1000 LH 44, MV AGUSTA F4 RR 998, KTM 1290 Superduke R, DUCATI X-Diavel S, HONDA CBR 1000 RR SP, DUCATI Multistrada 1200 S, DUCATI Monster 1200 S, DUCATI 1299 Panigale, DUCATI Monster 1200, DUCATI 1260 S Multistrada, DUCATI 1199 Panigale, DUCATI 1199 Panigale Superleggera, APRILIA Tuono V4 R 1000, APRILIA Tuono V4 RR 1100
Operability Up
Replacement from NisshinOEM.
From the initial touch, the softness of the touch is softer and the more you hold it in, the more it works, and I felt that the operability is much better than before.
I even regretted wearing it and wished I had changed it earlier.
View detail
Installed on New Model GSX1300R HAYABUSA
[How is it used?
First installed on a 2023 GSX1300R HAYABUSA!
The OEM MASTER was too big, tacky, and too hard to grip, so we replaced it with this one.
I have always used BREMBO, but the moment I saw this VRD for the first time, I was attracted by the beauty of the forging and Quantity of this product!:Pair (for Left and Right) Both were purchased.
Even though I have always been a brembo guy, I tried GALE SPEED for a while and it was surprisingly good!
Was the one you received as per Image?
The box is yucky and full of luxury.
A little more expensive than a brembo box? The feeling that the box was a bit more expensive than brembo's box was already conveyed to us before we opened it.
So the first impression is the best!
Was the installation difficult?
It was a bit complicated to install on the GSX1300R HAYABUSA.
If you want to use OEMHose as is [30MM]. I need an extended Banjo adapter. That would save me from having to buy an OEMHose. Nice savings!
How was your experience with it?
While the OEMMASTER is 19mm, we chose this 17.5mm.
The reason is that the OEM Caliper Piston is 30mm*P4, so 17.5mm is the most suitable size. 19mm is fine, but the grip is not so comfortable and hard, so 17.5mm is better. Please choose this size for your GSX1300R HAYABUSAOwner.
[Included Parts:were they on?
Stickers, Instruction Manuals, etc. I don't want to put Stickers because, frankly speaking, they are too flashy. I don't want to put Stickers because they are too flashy, to be frank.
[Was there anything that disappointed you?
Not particularly, I guess. Just expensive, from my friend's point of view, it's like lower than brembo:.... But this one is higher up!
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
It would be great if it came with a Switch.
View detail
Fits: YAMAHA YZF-R7, YAMAHA YZF-R6 S, YAMAHA YZF-R1 SP, YAMAHA YZF-R1, YAMAHA XJR 1300, YAMAHA YZF 1000R, YAMAHA XJR 1300, YAMAHA XJR 1200, YAMAHA MT-09, YAMAHA MT-07, YAMAHA FZS 1000, YAMAHA FJR 1300, YAMAHA BT 1100, YAMAHA FJR 1300, SUZUKI Hayabusa, SUZUKI GSX-R 750, SUZUKI GSX-R 600, SUZUKI GSX-R 1000 R, SUZUKI GSX-R 1000, SUZUKI GSX-R 1000
At first I was puzzled by the difference in Touch.
I was happy with the OEM Nisshin so far, but since the Caliper is brembo, I thought it would be better than what I have now. I bought it because I thought it would be better than what I have now.
I am not a fan of snaps and touches, so I was a bit confused at first, but I thought the Lever ratio 18 would be good for control. I would like to try various things with Winding when the road surface temperature rises a little more.
View detail
Fits: YAMAHA YZF-R1, YAMAHA YZF-R6, KAWASAKI ZX 14 R, KAWASAKI H2R, DUCATI 1103 V4 Panigale, TRIUMPH Street Triple RS 765, MV AGUSTA F4 1000 LH 44, MV AGUSTA F4 RR 998, KTM 1290 Superduke R, DUCATI X-Diavel S, HONDA CBR 1000 RR SP, DUCATI Multistrada 1200 S, DUCATI Monster 1200 S, DUCATI 1299 Panigale, DUCATI Monster 1200, DUCATI 1260 S Multistrada, DUCATI 1199 Panigale, DUCATI 1199 Panigale Superleggera, APRILIA Tuono V4 R 1000, APRILIA Tuono V4 RR 1100
Genuine Brembo 17RCS Corsa Corta Master Cylinder
One of my customers is going to out this bike on the track so I went to work on the braking system. One of the first things I wanted to change was the annoying stock master cylinder. Obviously, Brembo was the way to go. I decided on this one as it fitted with the specs of the bike in mind. Finding the correct master cylinder was not hard but there were a few choices but I went for this one, the 17RCS Corsa Corta in the end. It had all the requirements I needed so it went in my basket. I had a few other parts and the shipping was reasonable for what I had. EMS got my order to me in 5 days. The master cylinder came with the standard stock lever length which was perfect for my needs. It is the 18 x 20 one so works good with teh floating calipers on the bike anyway. It came in the Brembo box and also came with a few copper washers. I had already sourced the HEL line that would make this all work. The master cylinder is a real piece of kit and fitted really well with the bike and the instrument cluster I was leaving in situ. Not a hard job once you have all the parts together. This master cylinder is awesome and so much better than the stock one. Oh and by the way, looks the nuts. There are just so many adjustments that you can definitely find the right setting for your liking. I do like the 18 ratio and H pivot setting. Very pleased with this part. Thanks Webike for the great service you provide. View detail
Fits: HONDA CBR400F, HONDA CBX750F, HONDA CB1100F, HONDA CB1100R, HONDA CB900F, HONDA CBR1000F, HONDA CBR600F, HONDA CBR750, HONDA VF400, HONDA VF750F, KAWASAKI KR-1/S/R, KAWASAKI Z750FXII/III, KAWASAKI ZR-7/S, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZX-7R
NisshinBrake master cylinder kit (Horizontal Type)
I wanted to finish bleeding the air out of the brake fluid in one go, so I replaced it together with the brake hose replacement. The touch of the brake also worked better than before, and I am satisfied with the large change. I recommend everyone to dress-up the front area! View detail