Reviews
On the MVX250F.
I used it to fill the front fork with air. It's good because I can fill low pressure like 0.4 properly. View detail
Save money compared to buying at Rose!
The color stands out and gives it a custom feel, and as a manufacturer, I feel secure. I usually use OEM products, but I bought this product for fractional adjustment as well.
The quality and appearance were satisfactory.
View detail
Convincing texture
SizeAbout 820×I bought the one of 2000mm 。
I liked the texture of the Nylon raising on the front.
When I unpacked it, there was a smell peculiar to Rubber, so I dried it in the shade for a couple of days.
I was not sure if I wanted to go with a less expensive competitor, but I am satisfied with the DAYTONA product.
View detail
Used for CRF250L
We used it to fasten X.A.M's Driven Sprocket.
The OEM is M10Bolt, so an M8 conversion Spacer is required to use this one.
The OEM tightening torque is 50 N.m, but when I tried to tighten it with the same torque, it seemed to lick, so I tightened it with a little less torque.
I wonder if you could write the stipulation Torque in the Package.
View detail
It got brighter.
Replaced Headlight Bulb on Z125PRO.
The purpose was not only to make the engine brighter, but also to reduce the load on the battery (power saving). The Z125PRO had LED lights from the beginning, so there was no need to replace the tail lamps. I thought about replacing the blinker light because it has a normal bulb in it, but I decided not to do it because the blinker relay seems to be built into the meter and it would be complicated to change it to LED. This time, I decided to replace the Headlight Bulb and the Position Lamp with LEDs, and for the Headlight, I chose this product, which was the cheapest among the Sphere Light products.
The replacement work was as simple as removing the headlight cowl and replacing the valve with the original one, and since the valve is compact, there were no problems with installation.
As for the feeling of use, the light is bright enough and feels very bright, probably because the light is whiter. I was able to drive safely at night. I was not bothered by the dispersion of the light. Unfortunately, there was not enough of an energy saving effect that I could really feel.
Compared to when we replaced the LEDValve on our ZRX1100 a few years ago, low-cost products are now on the market, and the hurdle for replacement has gone down. If you are concerned about the brightness of your lights, we recommend replacing them with LEDs.
View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Z1000, KAWASAKI Ninja1000SX, KAWASAKI VERSYS 1000
Replacement is easy.
ninja1000 is a Quantity:Pair (for Left and Right) Remove the Upper Cowl of the BoltQuantity before Tank:Remove the 2pcs and lift it up to reveal the air cleaner box. Next, remove the screws around the box with a Phillips screwdriver and remove the lid to replace the air filter. This filter is just fit like the OEM one. View detail
It looks like it will fit in the stated capacity.
2.The product is up to 5L, but it seemed like a Limit at about 2.3L.
It's in there with no problem, so it's supposed to be in there as described.
It's much easier to dispose of than the previous Dan Ball box was.
View detail
It was just like the image.
I have just purchased a DDR−S100 with KAMUI3 for the purpose of fixing the Wiring to operate it as a HelmetCamera.
My DDR−S100 was modified to be able to cut the cord in the middle and connect it with Waterproof Coupler after the USB cord was disconnected. The third image shows the Helmet side. By connecting the other side of the cord connected to the Mobile Battery to this side, the cord does not get in the way when attaching and detaching the Helmet.
This time, when I use KAMUI3 for motorcycle commuting, I thought it would be better to have a DriveRecorder, so I decided to install DR−S100 on my helmet, and selected this product as just the right one to fix the Power Cord.
This 3mm TubeHolder was not bad looking and had just the right diameter to move it a bit against the thickness of the Wiring.
I have used 5mm diameter ones in the past, but they can also be cut and used, and I think they are quite user-friendly Parts. However, the adhesive strength is not very strong, so you need to be careful where you apply it. If it comes off, I will reapply with a stronger double-sided tape.
View detail
Almost perfect except for the price.
The front and rear stands seem to be the best in a certain manufacturer, but this product is sufficient for cleaning and simple maintenance at the Amateur level.
However, the price could be lower, so the rating was not a perfect score.
View detail
Shape is almost OEM
OEM Clutch initial position is not quite right, so it was replaced.
I tried to use a Z company's one before this one, but it had the same model number as the S1000, but the shape of the cutout for the mounting position was different, so it stopped in a slightly retracted position. I wanted to make the initial position closer, so the position was better, but the Low RPMAssist was almost ineffective. I don't need it, but I don't like the fact that a certain function doesn't work, so I decided to use this one, which has a different model number from the S1000 and the GT. The adjustment method is Screw, which is a bit uncool, but it works just fine.
I changed the color, but the shape is almost the same as the OEM shape, so I wondered if there was something more I could have done. I thought it would have been nice to have something more.
View detail
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
Fits: YAMAHA FAZER8, YAMAHA FZ8S, YAMAHA MT-07, YAMAHA MT-09 TRACER GT, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-09SP, YAMAHA MT-10, YAMAHA MT-10SP, YAMAHA NIKEN GT, YAMAHA NIKEN, YAMAHA TDM900, YAMAHA XSR700, YAMAHA XSR900, YAMAHA YZF-R1, YAMAHA YZF-R1M
When in doubt, this is it.
I bought this to match the Rear, and unlike the Rear, which is flashy in material and appearance, this is a plain but Large component.
Without hesitation, we chose SUNSTAR because of its security and reliability. We have and will continue to choose SUNSTAR for our replacements.
View detail
Purchased oilfor replacement for ninja1000
Items necessary when changing oil.
It can be disposed of as combustible trash as it is.
I think I will continue to Repeat Emon because other Manufacturers are expensive.
The only drawback is that the Oil will ooze out and if you don't double wrap the Vinyl and dump it, the rest will look Large weird.
View detail
Fits: HONDA GB350, HONDA GB350S
I think COSPA is expensive
I bought a new car with the new Type added and I replaced it.
The bend of Lever was good and it was easy to finger.
Clutch side rattles have been reduced and the clutch is easy to grip.
Some products are expensive, but Quantity:Pair (for Left and Right) So I think the cost performance is high.
View detail
Satisfied, except for the price.
The quality is good and satisfactory. If only the price could be kept a little lower. View detail
Fits: HUSQVARNA TE511, HUSQVARNA FE501, HUSQVARNA TC250, HUSQVARNA FE350, HUSQVARNA FC250, HUSQVARNA TC125, HUSQVARNA FE250, HUSQVARNA FS450, HUSQVARNA FC450, HUSQVARNA WR125, HUSQVARNA TE125, HUSQVARNA TE250, HUSQVARNA FE250, BETA X-Trainer 250, BETA RR2T 250, HUSQVARNA FE501, HUSQVARNA FE350, KTM BREMBO 125-530 XC-W 06-17, HUSQVARNA TE300, KTM 450 Rally
Nice upgrade
They will fit. They fit in the factory perches as good as the factory levers, and do fit behind the factory handguards with plenty of clearance. They are a well made product. Best levers I've ever owned. Crashed multiple times in hard pack, and soft conditions. They haven't even deformed. Will purchase for every dirtbike I own moving forward. View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI SV650, SUZUKI SV650X, SUZUKI V-Strom 650, SUZUKI V-Strom 650 XT
Dare Standard Plug BP5HA
It is replaced at 6 years and 20,000 km.
I was hesitating between Windshield IRIDIUM and Standard Plug BP5HA, but I dared to go with Standard Plug BP5HA.
There is a Gap in the poof.
I can't rely on the burn because of Injection, but Plug is already delirious.
Especially, Sub plug (SV650X has a Plug on the Head with a Quantity:2pc. Set at a time) had soot stuck to both the front and rear sides.
Is this how it's supposed to be? I don't know.
Last time vehicle was inspected (10000 km traveled) I didn't replace them with beans because I thought they were not expensive, but I thought I would replace them with Malu beans next time.
I noticed that the Radiator was distorted when I was replacing it. It seems that it had been hit by the ground when it was standing on the ground.
I was wondering why the Oil cooler fan was making strange contact with the Head.
The Radiator guard I bought occasionally cannot be installed! It's defective! Your Radiator may be distorted!
View detail
Cospa best
I haven't driven after the replacement yet, but I'm looking forward to it.
I will make adjustments in the Rear in the future.
View detail
Fits: SUZUKI GSX-S1000, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-R1000 R, SUZUKI GSX-R1000, YAMAHA YZF-R6, YAMAHA XSR900, YAMAHA YZF-R1, YAMAHA TRACER900, YAMAHA TRACER900 GT, YAMAHA MT-10 SP, YAMAHA MT-10, YAMAHA MT-09 SP, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA FZS1000FAZER, YAMAHA FZ1-S FAZER, YAMAHA FZ1-N FAZER, KAWASAKI ZZR250, KAWASAKI ZEPHYR400
Highly durable Steel
Used on first generation Ninja 250R.
Is this OEM or is this the only Sprocket that's steel and highly durable?
I prefer Black Sprocket, so if that's the case, my options are narrow.
I like the look of Parenthesis.
The paint job is also Beauty, so it is comparable to Duralumin products.
I mean, Material:So much more expensive than Aluminum...
Installation is DIY.
No special sukill will be needed.
Lock nut is also black because it is black.
View detail
I don't know. Self-satisfied.
The Throttle Wire was right above the Brake Lever Screw, unlike the Instruction Manual, so it was difficult to remove the Throttle Wire, which was Large and strange.
If not, installation is easy.
The quality is high, and the adjustable lever is nice, but it might be better if it wasn't so expensive.
The price is quite expensive.
View detail