Reviews
Fits: KAWASAKI KR-1/S/R, KAWASAKI KLR650, KAWASAKI KLR650, KAWASAKI KLR650, KAWASAKI KR-1/S/R, KAWASAKI KLR650, KAWASAKI KLR250, KAWASAKI EN500, KAWASAKI CS250
Might increase fuel economy?
The FSprocket has not been replaced yet and has not been run much, but it feels good.
The Meter reading was previously 4000 rpm at 60 km travel, but after the replacement, it became 3500 rpm and I was able to travel up to 6th gear without any discomfort.
Next time I will replace and adjust RSprocket and see.
View detail
Recommendation for those who are anxious to draw a Maintenance Stand alone!
Although an instruction manual is included, it does not explain the details of how to assemble the unit, which was confusing at first. I would have liked to have a guide to the screw holes to be used for the approximate number of inch tiers.
There was a product video on how to use and assemble the product, so I checked it out and assembled it. The video was very helpful.
The NINJA1000's front tire (120/70Zr17) was firmly secured and stood on its own. It also felt stable when lowering the bike.
I used to do maintenance only with the Rear STAND, but when I lifted up the bike by myself, I didn't hang it properly and it fell over. I wish I had bought it before I stumbled...I would like to recommend this product especially to those who work alone to avoid damaging a large motorcycle.
View detail
To prevent Axle Nut from loosening on older cars.
I used this as a split pin to prevent the Axle Nut from loosening, which is common on older cars. I always do this because it is easier to purchase than to look up the OEM Product No. and order one at a time.
For Motorcycle, the 3 sizes included in this kit should be sufficient for Large.
View detail
Fits: HONDA DAX125, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA SUPER CUB110PRO
Mounted on CROSS CUBJA60
Installed for dress-up and ease of gripping.
My hands are on the Large size, but OEM is a bit far away and my hands get tired after riding long distances, so I bought this. I am glad I replaced it.
View detail
Fits: HONDA CBF1000, HONDA NC700X, HONDA NC700SXL TYPE LD, HONDA NC700S, HONDA CBR250R, HONDA CBR250R, HONDA CBR1000F, HONDA CB650F, HONDA CB500 F, HONDA CB400X, HONDA CB400SF Ver R, HONDA CB400FA, HONDA CB400F, YAMAHA WR250X, TRIUMPH Tiger 800XC, TRIUMPH Tiger 800, TRIUMPH Thruxton 900, TRIUMPH Thruxton 865, TRIUMPH Street Twin 900, TRIUMPH Scrambler 865
Brake to JackKnife if you apply it strongly ".
This was the first time for me to use the Metal pad, but I have the impression that it works harder than the previous Golden pad.
I grabbed Lever with my usual BrakePoint and it worked so well that I JackKnife'd it unexpectedly.
We are still waiting to confirm the durability of the product, but as for the effectiveness, we are satisfied with it.
View detail
Fits: SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI ZZ (ZZ), SUZUKI Verde (VERDE), SUZUKI Verde (VERDE), SUZUKI Verde (VERDE), SUZUKI STREET MAGICII (STREET MAGIC II), SUZUKI STREET MAGIC (STREET MAGIC), SUZUKI STREET MAGIC, SUZUKI LetsIIS (LETS Two S), SUZUKI LetsIIS (LETS Two S), SUZUKI LetsIIL COMBINATION BRAKE (LETS Two Elle Combination Brakes), SUZUKI LetsIIL (LETS Two L), SUZUKI LetsIIL (LETS Two L), SUZUKI LetsIIG (LETS Two Gee), SUZUKI LetsIIG (LETS Two G)
Excellent braking performance.
I used to use Shoe of other brands, but this time I used NTB for the first time. I don't feel much change in the effect, but the brake noise during operation has been eliminated. It feels good. View detail
Fits: Others Wire clutchCompetition model, SUZUKI RMX450, SUZUKI RM-Z, SUZUKI RM, KAWASAKI KLX450R, KAWASAKI KX-F, KAWASAKI KX, YAMAHA WR-F, YAMAHA YZ-F, YAMAHA YZ, HONDA CRF-X, HONDA CRF, HONDA CR
Definitely lighter.
I had been using OEM Clutch for a long time, but it was too heavy and tiring, so I replaced it with this one.
To install, remove all the originally attached clutch lever and holder, leaving only the wires in place, and then install.
The dust cover is screwed on, so it must be disassembled and assembled before installation.
Also, the Clamp portion is rotated so that it is less likely to break than a regular Lever or OEM.
The Nut that adjusts the distance of the Lever is also hexagonal, a spec. that can be firmly fixed in place.
I prefer to set it quite far away, but it feels quite light when I pull the lever, I don't know if it's because of the Ratio or some other secret, but I think you can feel it the moment you hold it.
View detail
Fits: KAWASAKI ER-5, KAWASAKI GPX600R, KAWASAKI KLE500, KAWASAKI KLF220, KAWASAKI Eliminator 600, MAGNI 1000 Australia2, MOTOGUZZI 1000 Ditna RS, bimota YB-4, bimota YB-6, bimota Dietsch 1000, bimota Flannel 1000, HONDA CB1100F, HONDA CB1100R, KAWASAKI 1000GTR, KAWASAKI 250TR, KAWASAKI EN400, KAWASAKI EN500, KAWASAKI EX-4, KAWASAKI FX400R, KAWASAKI GPZ1000RX
Idling stabilized?
I changed the oil as part of maintenance, and it seems to have stabilized the idling, but I don't feel that the power is increased. I really don't know if the period to change the oil was too short and the oil was not so deteriorated, but it is an old motorcycle and I will replace the oil as soon as possible. Next time I will buy a Torque wrench and tighten it with the specified Torque. View detail
![VXSeriesChain 520VX3 Gold [with Crimp(ZJ)Joint]](https://img.webike-cdn.net/catalogue/images/59741/520VX3_G&G_P.jpg)
Fits: HONDA 400X, HONDA 400X, HONDA CB250R, HONDA CBR250RR, HONDA CBR400R, HONDA CRF250M, HONDA CRF450L, HONDA CRF450RX, HONDA REBEL(REBEL)500, YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZ250X, YAMAHA YZF-R25, YAMAHA YZF-R3, SUZUKI GSX250R, SUZUKI SV650, SUZUKI SV650, SUZUKI SV650X, SUZUKI DL1000 V-STROM250, SUZUKI DL1000 V-STROM250
Maximum speed has increased ?
Conversion to 520 Chain (and Sprocket), speed was up in almost all areas at the same RPM as before?Chain lightening was more effective than poor modifications. View detail
Fits: YAMAHA YZ125, YAMAHA WR125, YAMAHA TY250 Z SCOTISH, YAMAHA DT200 WR
Quickly to run
With the Front12T, you will be running Quickly, both on forest roads and in town.
It is affordable and I feel the effect of the replacement.
View detail
Fits: HONDA DJ-1, HONDA DJ-1R, HONDA DJ-1L, HONDA DJ-1RR, HONDA NSR50, HONDA NSR50, HONDA XR50 MOTARD, HONDA Express, HONDA CAREN S, HONDA GYROUP, HONDA GYROX, HONDA GYRO CANOPY, HONDA JUST, HONDA JULIO, HONDA JOY, HONDA GIORCUB, HONDA Giorno, HONDA GIORNO DX, HONDA SQUASH, HONDA SPACY50
Easy installation, no brightness problems.
Until now, we had been using Type with LEDs affixed at the top and bottom, but the straightness of the LEDs was poor when Up is lit, so we always used the LEDs facing down.
This type of LEDs are affixed in the LeftRight type, so the straightness when the LEDs are up is also OK. This time, I installed it on a square eye light, but I think it would be best for a round eye light. Finally, I am satisfied with the brightness.
View detail
Tail Bulb replacement for KSR's Fender Eliminator Kit
I purchased a used KSR80, but the previous owner installed a Fender Eliminator Kit, and the tail lamp is a Lucas type.
There was a Trouble with Tail Bulb immediately after purchase.
I removed the Lens to see the model of the Lamp to replace it, but unlike the usual Double Bulb, the head was a Small Rhinoceros Bulb.
This Type was not sold at Home center or Car Shop 。 Maybe MotorcycleParts specialty stores have them, but I can't find any near me. 。
However, because the length of the Tail Bulb was different, it interfered with the Lens, causing the Lens to chip, melt, and consume more power due to its higher wattage.
I had put it off because it was inexpensive but the shipping and other things made it needlessly expensive, but I had some shopping to do at WeBig, so I bought it as a package deal.
After installation, there was no interference (obviously), and since the Watt number was lowered, the power consumption was also lowered, eliminating the concern factor.
I am planning to eventually switch to LEDs, but there is a barrier of full-wave rectification, so I may end up putting it off.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Firmly.
I could not tell how light the Clutch was, but the build quality was solid, as if it were an OEM product.
Durability, that is the most decisive factor.
View detail
Fits: HONDA MONKEY125, HONDA SUPER CUB 50, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110 PRO, HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA glom, HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA glom, HONDA CROSS CUB 50, HONDA CROSSCUB110, HONDA WAVE125R, HONDA CZ-i110, HONDA WAVE125S, HONDA WAVE125i, HONDA ANF125innova
Changing from iridium to iridium
It was time to replace the Plug.
I've been using Iridium Plug.
I decided to give it a try since it's a new release.
I can't tell the difference between the iridium plug and the iridium plug by feel when I see it installed...
The iridium has a life of 5,000 km, but it was replaced after 10,000 miles.
After 5,000, they were losing fire and fuel efficiency.
The life span of motoDX is said to be twice as long as that of motoDX.
As of now, we have over 6,000 on the road and have not experienced any misfires or fuel consumption deterioration.
If there is no change in performance compared to iridium but a longer service life.
I think it's worth replacing.
I think it's a good thing in general.
I give it a 5 star rating with high expectations.
View detail
520Conversion Demerit
It is cheaper than collecting OEM parts, and as you all know, there is a Merit to make the 520. However, the Noise when driving will be Large.
It sounds like the sound when the bottom of the teeth of the front sprocket (Driven Sprocket) hits the Roller of the Chain.
The OEM Sprocket has a Ring-shaped anti-vibration Rubber, which reduces Noise.
As a countermeasure, I had some DAYTONAInsulation Glass WoolSeat left over from a previous purchase at Webig, so I attached this to the inside of the Sprocket Cover.
As an effect, Noise became much smaller.
View detail
Bolt hole in rear sprocket is Large
It is cheap and good, but the only thing that bothers me is that the Bolt hole on the Rear sprocket is Large. I'm worried that it might move during use. View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
Fits: HONDA glom, HONDA glom, HONDA glom, YAMAHA RD50, YAMAHA GT80, YAMAHA PW80, YAMAHA GT50, YAMAHA FS80 SE, YAMAHA FS-1, YAMAHA DT80 M/MX/MXS (-84), YAMAHA FS-1, YAMAHA FS-1, YAMAHA DT50, YAMAHA DT50, YAMAHA DT50, HONDA LITTLE CUB, YAMAHA BW80, HONDA MONKEY R, HONDA LITTLE CUB, HONDA MONKEY
periodic replacement
I consider them periodic replacement parts.
Chain and Sprocket exchanged for 25,000
Refueling is performed every 1000 km at the WAKOSChain spray
Some people think that the seal chain does not need refueling.
Lubrication is necessary to prevent rusting of the chain and to lubricate the sprocket!
CROSS CUB in JA10, running over 95,000 km.
No drivetrain problems to date.
View detail
Fits: DUCATI 600SS, DUCATI 748, DUCATI 748, DUCATI 748, DUCATI 750 Santa Monica (88), DUCATI 750 Montjuich (87), DUCATI 750PASO, DUCATI 750SS, DUCATI 750SS, DUCATI 851SP3, DUCATI 851STRADA, DUCATI 888 STRADA, DUCATI 888 STRADA, DUCATI 900MSS (93 - 97), DUCATI 900SL, DUCATI 900SS, DUCATI 900SS, DUCATI 900SS, DUCATI MONSTER S2R, DUCATI MONSTER400
Blacking around Chain is completed.
What made you decide to buy?
However, after the start of the New Year 2024, I started to collect parts little by little and decided to do the customization that I had envisioned since last year… The contents of the customization were the replacement of the Front and Rear Sprocket and Chain. I purchased the RK BL Black Scale Series Chain BL520X-XW, which had been a favorite of mine for a long time because of its high evaluation in Impression, and waited for the spring sale.
[How was the installation?
To change the chain, you will need a racing stand to lift the rear tire and a tool to cut and caulk the chain. We recommend DID's Kashimaru-kun! This is also listed as a recommended tool in the 6R service manual. Originally, you need to cut a long chain to do the work, but you can buy the chains we carry at Webic in the number of links you need. This was the second time for us to replace the seal chain, and we thought we had gotten used to cutting and caulking the chain, but the chain is an important safety part of a motorcycle. We did not let up until the work was completed, checking the chain over and over again.
How was your experience with it?
RKBlack scaleSeriesChain is not painted but coated with BLACK electrodeposition. Brass plating is applied to the pins and rollers to prevent rusting. The contrast between black lacquer and gold enhances the custom feel. The SUNSTARRACINGSteel rear sprocket was also replaced at the same time, so the custom look around the chain has been enhanced.
View detail