Reviews
Took a while but it’s perfect. Has the flared opening making it a true upgrade over stock. Very cool
Really nice piece. Flared mouth so it is an actual upgrade. Might add some more urethane to smooth the transition from CF to plastic insert View detail
Custom look
The Instruction Manual was also good and easy to understand.
If you are not confident about the installation, you can use Shop.
I think you should ask for it... ♪
View detail
Installation review
I bought it to change the rear luggage rack, and contrary to my worries, it fits well. However, you have to separate the air duct and pull it hard from the inside with pliers to make it fit all the way.
There is no difference from the other parts and the finish is clean. I dressed it up at a low price. -------------------------------------------------- -------- I bought it to change the rear luggage rack, and contrary to my worries, it fits well. However, you have to separate the air duct and pull it hard from the inside with pliers to make it fit all the way. There is no difference from the other parts and the finish is clean. I dressed it up at a low price. Powered by Google Translator
View detail
Left Side is Refreshing
Joint is Rubber, but because it is tightly made and stiff, it is tough to install without removing the Air cleaner cover.
There seemed to be no worry about it coming off that way, and the appearance was quite Refreshing!
View detail
Alot bigger than stock
Another awesome product from SP Takegawa, need to modify stock air box to allow the bigger intake to fit but it is worth it. Engine can breath so much easier now. View detail
Custom and Face looks great!
[How is it used?
Stand out and be great!
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy if you are self custom in a certain way.
How was your experience with it?
Looks good, tight and cool.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
The product is a little thin, so a little more reduction in cost would be better.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
I recommend it for the low price.
It is a good product in terms of practical design and low price.
If the product is not installed properly due to shaking due to a large impact, it may come off or become distorted.
We recommend that you use this product at first and then exchange it for another product later.
In terms of appearance, this is a recommended product.
-------------------------------------------------- -------- It is a decent product in terms of practical design and inexpensive. If the product is not properly mounted through a big shock, it may be missing or distorted if the product is not mounted properly. At first, I recommend using it as this product and later exchanged to other products. It is recommended in appearance. Powered by Google Translator
View detail
Needs a little processing.
Mounting on zx4r
When we first aligned it, it was not accurate at all.
The warp is so shallow that when I pressed the tip of the Center, both ends floated quite a bit, the largest 8mm floated. It was too shallow to be held by double-sided tape. Finally, I heated the shallow part with a dryer and bent it. Fortunately, I was able to fix the problem by using cheap Carbon, which softened up considerably.
And the depth? I'm not sure if it's not deep enough or if it's installed in the wrong position, but I can see the Green.
View detail
Customized
I don't know how effective it is, but it gives a custom feeling. The quality is as expected. View detail
Securely attached, strong netting
The air filter cover made by another company was installed, but the adhesion of the mesh part came off, and although it was repaired by Bond, it came off immediately.
The netting is solidly constructed with no risk of detachment due to its built-in structure.
However, the ducts are perfectly fitted and securely installed, with no wobble, and there seems to be no concern about the ducts coming off while driving.
The appearance is also neat and tidy.
When installing the Duct, it is better to remove the Air cleaner box before installing the Duct into the Air CleanerBox, because the fit of the Duct into the Air CleanerBox is Large strange, and it is easier to apply force.
View detail
I do not know if it is cold.
[How is it used?
I installed it on my XJR1300C. Even though it is not listed, it is the same as the NORMALXJR, so I was able to install it without any problems.
I have installed YOSHIMURA's Oil Temperature Meter, but I could not see any change in oil temperature.
Was the one you received as per Image?
It was just as Image.
As expected of MORIWAKI, the construction was very good.
Was the installation difficult?
Mount bolt of oil cooler to quantity:It is very easy to remove the 2pcs and insert this product between them.
How was your experience with it?
I do believe that the amount of air intake has increased.
I think so because the entrance is LARGE as shown in the image.
[Included Parts:were they on?
No, there is not. The OEM Bolt is also reused for installation.
[Was there anything that disappointed you?
Not particularly
View detail
I wonder if they are Refreshing.
OEM air duct removal and installation.
The Rubber was soft and easy to install and remove with the heat stroke alert in effect.
If it's winter, you might have a hard time.
View detail
Nut is not well fixed.
Purchased to remove the flap valve and make it full power.
It took 7 months to deliver the product.
Replacement from Straight machined OEMDuct, weight reduced from OEM approx. 350g to approx. 285g, which is like an error.
With a weight difference of this magnitude, I would like to see the product sold at a lower price in resin instead of Carbon.
I bought an OEMCap (92066-0717) to plug the hole in Solenoid, I wanted it to be plugged from the beginning because I don't think people who replace such parts would leave Solenoid.
The Gasket with the Frame is made of 100-yen Gap Sponge.
Installation is quite tricky. Both Duct and Frame have BALI at the Center, so they are like Seesaw and do not go deep enough.
When the bolt is forcibly attached while pressing down, the nut on the duct side rotates and cannot be tightened or loosened....
The OEM has a star-shaped nut embedded in the outer diameter that does not rotate, but this one has only a lightly crimped round type nut, so it rotates all the time.
In the end, I managed to install the FrameCenter by shaving the contact surface of the FrameCenter. I don't plan to remove it, but I'm not sure if it will come off since I put a screw lock on it.
The intake changed to Large width, so I adjusted the ECU before starting, and the effect was excellent.
The Torque is clearly increased from the start, and city driving is easier.
Motorcycle is a monster to begin with, but the Peak power has become even greater, and it cannot be handled by ordinary people.
View detail
Simple and Design, texture, etc. are very good.
Simple and Design, texture, etc. are very good.
This area is trustworthy, as is ZETABrand.
However, because the soft material is designed to fit into the groove of the Air cleanerBox, even a slight bump can cause the hook to the Air cleanerBox to become shallow, making it easy to fall out. (For example, when your knees hit a little when hanging Center Stand, etc...)
View detail
Refreshing appearance, loadability up!
It looks Refreshing and better! This Parts does not change the driving performance, but the purpose of replacing it was the appearance and loadability. Originally, the air duct was designed to face upward to prevent water absorption. I think it was originally designed to look like a snorkel in a car, but I rarely drive in such a place, and even if I change to these Parts, the air duct is still on the top, and it looks cooler. I feel that there are a lot of good things about the new parts, such as the fact that the air duct is still there and the approach to the rear suspension is easier. As a bonus, the bolt mounting base that appears when the OEM air duct is removed appears as a good place to hang a net hook when loading! This is a great solution to the problem I had when I used to go camping and couldn't hang my hooks because of this duct!
It has a good texture, looks good, is easy to load Up, and even a Custom beginner could finish putting away the tools in 15 minutes.
View detail
Refreshing
After replacing the rear suspension, it became difficult to install the OEM ducts, so I was running with the ducts upside down, but the parenthesis was not good, so I purchased this product. The installation was so easy that it was a no-brainer. I wish the price was a little lower.
I am not sure of the effect at all, but I am satisfied with the appearance of the Refreshing together.
View detail
Looks good!
I am not sure of the effect.
Maybe we'll find out when we drive more distance.
It looks pretty Cool.
View detail
Fits: HONDA MSX125, HONDA glom, HONDA glom, HONDA glom
Thick.
I'll have to replace the slobo as well to see the effect. View detail
Securing the Loader Hook on the cargo bed
Purchased product because the Loader Hook on the LeftFront cargo bed cannot be secured.
Duct Quantity for installation:I had some difficulty with the set, but managed to get it in place by using a SmallSlotted screwdriver.
Others have commented that there was a whining sound when driving, but I could not tell while driving because of the engine noise, but I could not help but notice such a sound when slowing down at traffic lights.
It looks OK because Refreshing and Loader Hook can be used without any problems.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS Cafe
Parenthesis OK
Anyway, Parenthesis is good.
It took a long time to deliver, but it was the right part to get.
Expensive but satisfactory.
View detail