Reviews
Black for a sense of unity
Tandem Footpeg for CBR600RR (PC40).
Rear brakeReserve tank is white in color because it was removed.
Installed to stand out.
The entire color scheme was unified in Black, giving it a tighter look.
It was good
View detail
I need an Instruction Manual.
High quality for the price.
I just want an Instruction Manual!
View detail
Custom standard
Custom standard.:If you are using Stainless Steel round flat or spring washers, you may want to change to these parts for a more stylish look. View detail
Fits: HONDA CRF300L RALLY, HONDA CRF300L, HONDA CRF250RALLY(S), HONDA CRF250RALLY, HONDA CRF250L(S), HONDA CRF250M, HONDA CRF250L, HONDA TRAIL125, HONDA CT125, HONDA MONKEY125, HONDA CROSS CUB110, HONDA CROSS CUB50, HONDA CRF110F
For Dress-up
Attached to the Yellow monkey, I think the One point of Red made a good Accent. View detail
ได้รับสินค้าแล้วครับ/ตรงตามที่สั่ง/สิ้นค้าไม่เสียหายใดๆ/ใช้เวลาในการส่งไม่นานมากครับ/มีโอกาสจะคงสั่งต่อไปครับผม View detail
Parenthesis well in a good way
[How is it used?
For Top box Upgrade.
Was the installation difficult?
Easy to install
How was your experience with it?
It's going to look good.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Point and hang of installation
Installed by Screw alone.
[With or without Instruction Manual
Instruction Manual can be viewed by reading the QR code.
View detail
Fits: HONDA Super Cub 50, HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA CROSS CUB, HONDA SUPER CUB110, HONDA SUPER CUB110ThailandMODEL, HONDA CUB100EX, HONDA CROSS CUB50, HONDA SUPER CUB 50
Looks good!!!
Checking Chain tension and mere window for refueling "Lid. But I'm all about the looks!
Texture is Up to Large width than Plastic lid!
As for installation, as mentioned in the Instruction Manual, the inner O-ring can be installed normally, but the outer one has to be put in one side while pulling it into the gap, and finally pushed in, so it is difficult to manage to fit it inside without it sticking out... (sweat)...
This price for just a lid... (laughs). Recommended for those who value appearance.
View detail
4LMONKEY
4LMONKEYHeadlight case6KakuBolt's plain washer8MM, used instead of spring washer8MM, fashionable. View detail
PetitCustom
Texture and quality are good, but not cosmetic enough for PetitCustom?
I'd still be in the $3,000 range!
View detail
PetitCustom
I got the PetitCustom and was concerned about the holes after the Fender Eliminator, but I'm glad I did. I wish the price was a little lower so it would be easier to buy... View detail
It is solidly built
The actual product is surprisingly large and solidly made.
I am thinking of Logo mark by Umbrella inside.
I am looking forward to seeing where I can install it.
View detail
Appeal YOSHIMURASpirits casually
I think most New Model KATANA riders will remove the Rear Fender.
Items to plug the holes in the Swing Arm.
Although the price is aggressive, the items are highly satisfactory for installation.
Bolt on OEMRear Fender for installation in quantity:Since 2pcs will be diverted, it is kindly not necessary to prepare a new one.
View detail
Happy with Billet parts!
If you know where to look, you know where to look.
I hear the MASTER lid doesn't need a middle lid.
I was a little confused because the O-ring for the OILFILLER cap is installed differently from the OEM.
I thought that if I had the Instruction Manual, I would not be worried. I thought that if I had the Instruction Manual, I would not be worried.
Replacement was basically a simple Packing porting and tightening with a Screw.
View detail
I wish Logo had a choice.
It would have been better if the logo could have been chosen between ”Kawasaki” and ”KAWSAKI”.
The installation itself should not be difficult, but there are three recommendations for User's own installation.
1.Curing Fender with Toweletc.
2.Remove the cowling (see Photo 1 and Photo 2, actual working time is about 1 or 2 minutes)
3.The tip of the flat terminal of the Horn is sharper than expected, so protect the terminal when removing and installing the Horn.
The rest of the procedure is as described in the instruction manual.
Edge of Bracket is sharp. Chamfering is recommended for those who are concerned.
Since this is not a location that is normally easily touched, it was installed in its current state.
According to the instruction manual, the angle between the Horn and Horn Bracket is at about 14 o'clock, but we decided to set it at about 13 o'clock in consideration of the handling of the Wiring. Since there may be some individual differences, it is best to use the instruction manual as a basis and match it to the actual vehicle.
View detail
Mesh re-covering
When the A-techSeat Cowl is installed, the mesh around the brake is reupholstered and tightened. View detail
rear fender panels
great price and great looking product for your cb1000r. I advise it for every honda cb1000r 2018> owner. I guess it looks great on black color cb1000r. View detail
Bolt was also replaced with Speedra's Fender Eliminator Kit.
I'm kind of in the middle of something...
I can grin.
View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY
Looks beautiful
Was advertised to fit a honda monkey but assumed it would work on my xr70. It's a quality product that fit perfectly and looks way better than the exposed cotter pin through pivot. Easy to install with 1 Allen set screw and pin. Seems to look better than the other brands. The price was good and shipping to America with all the politics going on seemed fast. The packaging was professional and I have no complaints. View detail
great kit at fair price
It's a great kit if you want to individualize your bike so it doesn't look like all of the others.Bling kit added just a splash of Honda red back to my bike.The kit was easy to install except the main timing plug. I was unable to locate an Allen wrench that fit it tight, it ended up with some scratched surface on the interior of the plug.Thanks webike View detail
Weight saving
[How is it used?
Previous Material:Stainless Steel and was heavy.
We decided on this product.
Was the one you received as per Image?
Design, etc. was exactly as shown in the photo at the time of purchase.
Was the installation difficult?
Since the long holes are machined, there is no difficulty in temporarily tightening and adjusting the position.
How was your experience with it?
Material:It is very light because of Carbon.
[Included Parts:were they on?
Bolt and color are included.
[Was there anything that disappointed you?
none in particular
Other items that would be helpful
The bolt is replaced with a Torque from another company instead of the one supplied.
View detail