Reviews
Fits: HONDA GORILLA, HONDA MONKEY
Can be used for groms.
[How is it used?
Rear suspension was replaced and ride height was increased.
Was the one you received as per Image?
Well, it's CQuality, but it's cheap, so it's OK.
How was your experience with it?
The angle is now as per Image.
[Points to note]
Side stands switch must be cancelled
Also, Screw can be put in from the back.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
For those who use in Grom, please buy Side Stand Switch Canceller
View detail
Fits: HONDA Ape 50, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 50, HONDA XR100 Motard, HONDA XR50 Motard
I am concerned about the strength…
[How is it used?
With the Rear Sets installed, the GCraft Side Stand Bracket was installed, but the mounting point was lower than the Normal Bracket, and it became necessary to shorten the length of the Side Stand, so we decided to purchase it.
Was the one you received as per Image?
Aluminum Cut-out is Parenthesis better than Image.
Was the installation difficult?
Spring hooks are easy to install.
How was your experience with it?
No problem, but Material:I am concerned about the strength because it is aluminum.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
The tilt is now good.
The side stand was getting tired and the tilt was becoming large. When the road was leaning Left, the STAND was leaning so much that it was a little heavy to get up, but now it looks good. View detail
crf250RALLY50 Corresponds to parking lot tilt
The parking lot of the house is slightly tilted.
The installation of an Aluminum Rear box.
Due to the above two points, there was a concern that the product would topple over to the Right Side when parked.
Therefore, Side Stand was shortened.
The installation was done by RED ZONE, from whom we purchased the Motorcycle.
After installation, the tilt was Larger on level ground, but no problem. Of course, there was no problem in the parking lot of the house.
The product looked great and was satisfactory.
View detail
Fits: SUZUKI GSX-S125, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-R125
Earthquake protection.
There have been a lot of earthquakes recently.
I was worried about OEMSTAND, so I decided to go with something with a lower center of gravity.
good point
Simply replace the existing STAND.
I put it in Handlebar Lock, 1st gear, and set it to this STAND, and it was Large sturdy at about 5 intensity of the earthquake.
A bad point
It is better to have two people for installation, one who is holding it down and one who is attaching it.
Short suspension compatible, but OEM suspension is also available. How about for earthquake protection?
View detail
It was early.
CRF250RALLY5019Standard
By MOTARDization
I could get rid of my standing position!
I'm glad I bought it
View detail
Fits: YAMAHA Cygnus X, YAMAHA NMAX155, YAMAHA MAJESTYS, YAMAHA AxisZ, YAMAHA NMax
Installation of N-MAX Side Stand Switch Canceller
My friend's Yamaha N-MAX is not able to run the engine without the side stand, which is inconvenient.
You are responsible for any problems that may occur since you are removing a function that is attached for safety reasons.
For safety reasons, I would not recommend it, but my friend seemed to be satisfied with Large.
The work itself is easy, as it is only a matter of replacing the Cover if it can be removed.
I think someone with a SuKill can make it on their own.
Well, since it is inexpensive, at 330 yen, you can't go wrong with buying it.
View detail
On gravel or unpaved surfaces.
When I park my motorcycle on gravel, it becomes unstable due to vibration and other factors that cause it to tilt, but this product made it stable.
It also prevents the ground surface from being scratched and the color of the Side Stand from being stained when parking a heavy Motorcycle, even on a dirt floor condominium.
Since it is a PlasticMaterial, it seems to be weak in strength, but it has managed to withstand a motorcycle weighing 250kg with a little distortion.
View detail
Fits: DUCATI Panigale V4, DUCATI PANIGALE V4 S, DUCATI STREETFIGHTER V4, DUCATI STREETFIGHTER V4 S
certainly
It is true that it was very good because it made it easier to STAND, but if I banked too much on the winding, it was scraped and bent. I think it is because of up-down because of the mountain road. View detail
Fits: HONDA CT125, HONDA CT110 HUNTER CUB
Very large effect on overloading of the Carrier, which is common in CT125.
It increases stability to the point where OEMs are frustrated as to why they could not do this.
The balance of the OEM is such that the front of the Carrier floats when you press down on it with your hand, even when unloaded, and it changes to a sense of stability that does not waver when you put a little weight on it.
Installation is simple and straightforward, but a Torque wrench is required.
In particular, the bolt near the under bracket needs to be tightened behind the crankcase, so if the screw hole is broken by Overtorque, the entire crankcase will have to be replaced. If you are not confident about this, bring the bolt in or ask someone who is familiar with it to do it for you.
Side stands sensors can also be used without modification if the wiring is changed. All Bolts are specified with a specific Torque, so be sure to observe the Torque. This is also stated in the assembly manual.
One regret I have is that the Center Stand interferes with the BackOffset if a Side StandAdapteretc. is installed to increase the installation surface.
This must be addressed with the use of the anti-embedding Platec.
Nevertheless, the product is relatively easy to install and highly effective.
View detail
Fits: HONDA glom, HONDA PCX150, HONDA PCX125, HONDA LEAD125, HONDA DIO110
easy and convenient
It is convenient to start the Engine with the Side Stand out by simply installing it with Couplet-on.
It is a simple but useful product.
View detail
Fits: YAMAHA JOG ZR (Evolution) [CV50ZR] 2003, YAMAHA JOG ZR (Evolution) [CV50ZR] 2004, YAMAHA JOG ZR (Evolution) [CV50ZR] 2006, YAMAHA JOG ZR (Evolution) [CV50ZR] 2007, YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle)
สินค้าตรงตามรูปที่ลงขาย สินค้าส่งจริง สินค้าส่งไว ของแท้ มาตราฐาน ตามสเปคแน่นอนครับ View detail
This stand from minimoto is great quality and at a good price. I have used it on my custom 1976 Honda xl75 cafe racer project. The stand is steel and is strong with good paint quality.
This stand from minimoto is great quality and at a good price. I have used it on my custom 1976 Honda xl75 cafe racer project. The stand is steel and is strong with good paint quality. View detail
Fits: KAWASAKI Z1100GP, KAWASAKI Z1100R, KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1000 (air-cooled)
trick looking side stand, idal for a zed that has been raised or lowered. well finished.
trick looking side stand, idal for a zed that has been raised or lowered. well finished. View detail